Wuhan Guide Sensmart Tech Co.,Ltd. IR510 Nano Series User manual

Statement：
This guide is applicable to the IR510 Nano series products, including
the following four models. The differences are as follows,please
carefully read this guide before using the thermal imager.
Our company shall not bear any legal responsibility for any
mistake and accident caused by own reasons or reasons of
any third party in the course of using this product by the user
or property loss and personal injury caused by misjudgment
against images.
We prepare this guide with the purpose of facilitating users to
use and understand our products. We will try our best to
ensure the accuracy of contents of this guide, but we still
cannot ensure the completeness of contents of it. Since we
have been continuously updating and upgrading our products,
we reserve the right to modify this guide at any time without
prior notice.
Thermal imagers shall not be pointed to high-
strength energy sources (including the Sun, laser
transmitting equipments and their reflection
sources), which otherwise will have a negative
influence on its accuracy and damage or
permanently damage infrared detector of it.
When the thermal imager will be not used for a
long time, charge the thermal imager at least 2.5
hours every two months during the storage, and
store the thermal imager in a dry and well-
ventilated environment.
Human eyes shall not be irradiated by the laser
designator of the thermal imager.
Do not charge the battery in an environment over
40℃.
A video output port is provided next to the USB interface at
the bottom of the thermal imager, and will output the image
of the thermal imager to an external monitor for display
through the supplied the video cable.
Simultaneously press "Image Mode Button + Zoom
Button" to turn on the video output; in the video output
status, there is a video output icon.
WUHAN GUIDE SENSMART TECH CO.,LTD.http://www.guideir.com
Model
Lens
19mm 25mm (supports
expansion lens)
Function
IR510 N1
IR510 N1 WIFI
IR510 N2
IR510 N2 WIFI
√
√
√
√
√
√
×
×
×
××
×
Wifi(APP) Freeze Image
enhance
√
√
×
×
×
√
×
√
Simultaneously press the “Image Mode Button + Brightness
Button” to switch on/off the cursor.
Cursor switch
SERIES SERIES

WUHAN GUIDE SENSMART TECH CO.,LTD.http://www.guideir.com
Before using the thermal imager for the first time, be sure to
charge the thermal imager for at least three hours with the
matched USB charger.
During charging, please pull out the USB cover at the bottom
of the thermal imager, insert the supplied USB charging
cable, and engage the power to charge the battery. (Charging
voltage is 5V)
During normal charging, the charge indication light will turn
red;
When the charging is completed, the charge indication light
will turn green.
When the thermal imager is turned on, the battery power
identification is shown at the lower left corner of the screen.
The lighted battery power identification shows the remaining
battery power.
The thermal imager has three power states: Power On,
Standby and Power Off；
Power On: Press and hold the power button for 2 seconds,
so that the thermal imager is turned on, and the startup
screen appears on the eyepiece;
Standby:
Manual standby: Press the power button to enter the
standby mode in the power-on status;
Automatic standby: In the power-on status, if there is no
button operation within five minutes, the automatic standby
prompt will pop up; The automatic standby will be cancelled
by any button operation during the standby prompt display;
Cancel Standby: In the standby mode, press any button to
cancel standby.
Power Off:
Manual power off: Press and hold the power button for 2
seconds so that the thermal imager is powered off;
Auto power off: In the standby state, if there is no button
operation within 30 minutes (default), the thermal imager will
automatically shut down.
WiFi Connection
The thermal imager can be connected by WIFI and mobile
phone, and most all functions（except Startup and
Shutdown）of its buttons being controlled remotely by
APP on mobile phone.
Users need to search and download “Thermal Viewer”
APP from a mobile phone application market, then open
the APP, find the WIFI “Handheld-TI” and enter the
password "12345678". Once the connection is
successful, users can operate the thermal imager
remotely.
Click this button to switch the white hot mode, black hot mode
and red hot mode;
White Hot Mode
Black Hot Mode
Red Hot Mode
WIFI switch
The object with higher temperature
shows in white or light gray;
The object with higher temperature
shows in black or dark gray;
The object with higher temperature
shows in red;
Press and hold the “Image Mode Button”
to switch on/off WIFI.
Click this button to enlarge the image by 2x and 4x in
turns
Freeze: Press and hold the button to freeze the current
screen with the Frz icon appearing at the left upper corner
of the screen. Press any button to retrieve the real-time
screen.
Image enhance: Press and hold the button to set 5
enhancement levels of image.
Zoom button
The diopter adjustment knob is used to adjust the
eyepiece diopter in order to suit users of different-
level myopia.
Diopter adjustment
Notice:This model is equipped with a 25mm extended
lens which can block the laser emission.
Click to set five brightness levels of the image;
Light/laser
indicator
Press and hold the button to switch
on/off the light/laser indicator.
SERIES SERIES

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void
your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.