Wunda E06 User manual

1
Mounting Steps
1: Release the front cover by inserting a screwdriver into
bottom channel and twisting.
3: Mount the backing plate in the wall socket using
a screwdriver and screws supplied.
2: To release backing plate, slide wire retaining clip upwards.
4: After connecting the receiver as per wiring diagram (see diagram)*, mount the thermostat on to the
backing plate and push down wire retaining clip, remount the frame.
*All wiring must be completed by a qualified professional in line with current regulations
Wiring Diagram
Potential free
output
Main control
circuit
E06
E8.413RF/E8.423RF Wireless Receiver (Single Zone)
✆ 0800 5420 816 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision Date: 30/04/2018

2
The indictor A is red when power is on
The indictor A is red and flashing when receiving the wireless signal
The indictor A is green and flashing when in code pairing mode
The indictor B is green when calling for heat
The indictor B is red when set to external limitation protection
The indictor B red flashing shows a sensor error
The indictor B green flashing shows entering the external limitation value select
Press the button for 8 seconds untill the indictor B flashes green,the receiver is now in
external probe limitation setting mode.
Press the button softly to cycle between the following four states.
Indicator A - green shows external limited at 30oC
Indicator A - red shows external limited at 40oC
Indicator A - yellow shows external limited in 55oC
Indicator A - without light shows no external limitation set.
The receiver will save current setting automatically when nothing is pressed for 8 seconds and will
quit the limitation setting mode.
Green Calling for heat
Red Limitation protective
Red ashing Sensor ERR
Green ashing Selected the limitation value
Green ashing Entering limitation value selected
Red Power
Red Flashing Receiving Signal
Green Flashing Code Pairing State
Green external limited at 30°C
Red external limited at 40°C
Yellow external limited at 55°C
None external limited closed
Description of work state Limitation value select (for external probe (if used))
Indicator A
Indicator A
Indicator B
Indicator B
Button
Press for
8 sec
*All wiring must be completed by a qualified professional in line with current regulations
E06
E8.413RF/E8.423RF Wireless Receiver (Single Zone)
✆ 0800 5420 816 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision Date: 30/04/2018

3
Code pairing method
On Thermostat (E8.2RF) enter the advanced settings by first switch off thermostat by pressing then hold while
switching thermostat back on . Next Press 4 times untill the following is displayed.
On Receiver press the button for 4 secs then release, indicator A will flash green , the
receiver is now ready to be code matched.
(NOTE: Indicator light will go out after 30 seconds of inactivity and process
will need repeating)
On thermostat press and will flash 3 times and then go out, the indicator
light A will turn back to red indicating that code match has been successful.
Selection Table
Your notes:
Parameters
Voltage : AC230V
Current : Max 3A
Wireless Frequency Output: 433Mhz
Effective Transmission Distance: 200m empty space
External Limatiation Valve : 30°C,40°C and 50°C
(if external probe is fitted)
Factory Setting : 30°C
Limitation Switch Differentail : -2°C
Ambient Temperature : -5~50°C
Protective Housing: Ip20
Housing Material: Anti-Flammable PC
Model Current Output Type
E8.413RF 3A One receiver, built-in & floor sensor
One receiver, built-in & floor sensor with potential free output
3AE8.423RF
*All wiring must be completed by a qualified professional in line with current regulations
E06
E8.413RF/E8.423RF Wireless Receiver (Single Zone)
✆ 0800 5420 816 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision Date: 30/04/2018

4
Your Notes:
Tech support opening hours are subject to change - please visit our website for the latest information
Revision Date: 30/04/2018