Wyrestorm CON-H2-EDID User manual

18Gbps HDMI In-line Signal Re-Clocker with EDID Management
CON-H2-EDID Quickstart Guide
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-EDID Quickstart Guide | 190530
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
• Advanced conguration of this product requires the use of the use of the
WyreStorm Management Suite v1.6 or higher conguration tool. Download
the latest version from the product page before continuing with the
installation.
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• While this product supports CEC for the HDMI outputs, WyreStorm cannot
guarantee compatibility with all forms of CEC communication.
In the Box
1x CON-H2-EDID
1x DC 12V 1A Power Supply (US/UK/EU/AU)
3x 3-Pin Terminal Block
2x Mounting Brackets
1x Quick Start Guide (This Document)
KEY
Passive HDMI
Control
Power
Analog Audio
Digital Audio
Amplifier
CON-H2-EDID
Rear
CON-H2-EDID
Front
Analog Audio
AC
Mains
HDR Source
Short Throw
Projector
Projector Screen
Audio Video
Receiver

Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-EDID Quickstart Guide | 190530
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
.
Audio Connections
Analog Audio Out
Tip:
Ring:
Left Channel
Right Channel
Sleeve: Ground (GND)
S/PDIF Digital Audio Out
Tip: Signal (+)
Shield: Ground/Return (-)
RS-232 Guidelines
This product uses a 3-pin RS-232 with no hardware ow control. Most control
systems and computers are DTE where pin 2 is RX, this can vary from device
to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
Relay Wiring
The relays on this product can be used to be trigger devices such as projector
screens that are Normally Open (NO) or Normally Closed (NC).
3rd Party Device
Pin 1 NO (Normally Open) ---> To ---> NO (Normally Open)
Pin 2 Common (Ground) ---> To ---> Common (Ground)
Pin 3 NC (Normally Closed) ---> To ---> NC (Normally Closed)
WyreStorm Connector
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that the output resolution of the source and display is supported by
this product.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
• Verify that all source and display connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the RS-232 cables are properly terminated.Refer to RS-232
Guidelines and/or Relay Wiring sections for pinout information.

Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-EDID Quickstart Guide | 190530
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
Setup and Conguration
EDID Dial Settings
The dial located on the front of the product is used to set the EDIDs based on the following table.
Resolution Dial Set
EDID copy from Output 0
1024x728 @60Hz 2Ch F
1280x1024 @60Hz 2Ch C
1280x720p @60Hz 2Ch 4
1280x768 @60Hz 2Ch E
1280x960 @60Hz 2Ch D
1360x768 @60Hz 2Ch B
1400x1050 @60Hz 2Ch A
Resolution Dial Set
1440x900 @60Hz 2Ch 9
1600x1200 @60Hz 2Ch 7
1600x900 @60Hz 2Ch 8
1680x1050 @60Hz 2Ch 6
1920x1080p @60Hz 2Ch 3
1920x1200 @60Hz 2Ch 5
3840x2160p @30Hz 2Ch 2
3840x2160p @60Hz 2Ch 1
Advanced Conguration
The following steps require the use of the use of the WyreStorm Management Suite v1.6 or higher. Download the latest version from the product page before
continuing with the installation.
Initial Conguration Tool Setup
1. Connect the converter to a PC using the RS-232 port. Refer to RS-232 Guidelines for pinout.
2. Open the WyreStorm Management Suite and select the CON-H2-xxxx Conguration Tool from the menu.
3. Under RS-232 Port Conguration select the COM port for the PC and set the baud rate to 57600.
4. Select the Connect button to connect the PC to the converter.
EDID Write from a File
If an EDID le is available it can be uploaded into the converter for setting the desired EDID.
1. Under RS-232 Port Conguration select the COM port for the PC and set the baud rate to 57600.
2. Under EDID Write select Choose File to select the le to upload.
3. Once the selection dialog closes, select Import to upload the le to the converter.
Connected Device On/Off Triggering
Devices such as projectors or displays connected to this product can be controlled from via connection to the RS-232 port. Commands for the devices are
entered within the CON-H2-xxxx Conguration Tool.
1. Under Power On/Off Pre Loading set the baud rate for the device to be controlled.
2. Select Send next to the Baud Rate to send it to the converter.
3. Enter a command for Power On and select HEX if the command is HEX.
4. Select Send next to Power On to send the command to the converter.
5. Enter a command for Power Off and select HEX if the command is HEX.
6. Select a delay time for powering Off the device after no HDMI signal is detected.
7. Select Send next to Power Off to send the command to the converter.
8. Select a String terminator to use for the commands and select the Set button.
Conguring Relays
The relays on the converter can be programmed to be Latch or Momentary based on the functionality of the connected device. This setting is the same for both
relays.
1. Under Set Relay Mode select Latch or Momentary for Relay Mode.
2. Select the Set button to send the setting to the converter.

Specications
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-EDID Quickstart Guide | 190530
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a
period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Audio and Video
Inputs 1x HDMI In: 19-pin type A
Outputs
1x HDMI Out: 19-pin type A
1x Audio Out: 3.5mm (1/8in) TRS Stereo
1x S/PDIF Out: S/PDIF Coaxial Digital
Audio Formats
HDMI Pass-through: 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos
S/PDIF Out: De-Embed: 2ch PCM | Multichannel: Up to 5.1 DTS and Dolby Digital
Analog Out: 2ch
Video Resolutions (Max)
Video Resolution HDMI
1920x1080p @60Hz 12bit 15m/49ft
3840x2160p @24Hz 10bit 4:2:0 HDR 7m/23ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft
3840x2160p @60Hz 10bit 4:2:0 HDR 5m/16ft
3840x2160p @60Hz 12bit 4:2:2 HDR 3m/10ft
4096x2160p @60Hz 8bit 4:2:0 7m/23ft
4096x2160p @60Hz 8bit 4:4:4 3m/10ft
Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 | BT.2100
Maximum Pixel Clock 600MHz
Communication and Control
HDMI HDMI 2.0 | HDCP 2.2 | EDID | CEC Triggering
Inputs supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included)
CEC CEC Power Triggering | Requires CEC compatibility
RS-232 1x RS-232: 3-pin Terminal Block - 3.5mm
Relays 1x Relay 2: 3-pin Terminal Block - 3.5mm | 1x Relay 1: 3-pin Terminal Block - 3.5mm | Max 1A load
Power
Power Supply 12V DC 0.5A
Max Power Consumption ≤2W
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing
Storage Temperature -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing
Maximum BTU 7 BTU/hr
Dimensions and Weight
Rack Units | Wall Box <1U
Height With | Without Feet 20mm/0.79in
Width With | Without Brackets 120mm/4.73in
Depth With | Without Handles 80mm/3.15in
Weight 0.23kg/0.51lbs
Regulatory
Safety and Emission CE | FCC | RoHS | RCM