1
7
3
9
4
10
5
11
6
12
2
8
90°
Take out the X-CAM sight 2 from the gift box, put
your smart phone into the phone holder. Do not turn on
the gimbal before the your phone has been mounted
balanced on the gimbal. If power button of your phone
is on the side of your phone, make sure not to press it
when you mount the phone to the phone holder.
Now adjust gravity of the roller. The phone is
tilted to the left in the above photo, you need
to push the phone to the right.
The phone is tilted to the right in the above
photo. To adjust gravity of the roller you need
to push the phone to the left.
Shake the X-CAM sight2 lightly, if your phone
remains balanced, congratulations that
adjustment of gravity of the roll is completed.
Fold the machine arm 90 degrees
perpendicular to the body, until the hexagon
screw hole reaches against the silver metal
part .
Hold X-CAM sight2 with your right hand.
Rotate the machine arm until screen of your
phone faces you. Now check gravity of the tilt.
Shake X-CAM sight 2 lightly. If the phone remains
balanced vertically, gravity of the tilt is OK, so no further
adjustment to gravity of the tilt needed. You can use
your X-CAM sight 2 now. Gravity of the tilt is fixed once
and for all.
If phone screen faces down as shown in above photo,
you need to adjust gravity of the tilt. Turn the hex allen
wrench counterclockwise as shown on Photo 10. Fold up
the roller arm to check tilt gravity again.
If phone screen faces up as shown in above photo, you
need to adjust gravity of the tilt. Turn the hex allen
wrench clockwise as shown on Photo 10. Fold up the
roller arm to check tilt gravity again.
Use the hex allen wrench packed in the
package to adjust protrusion of the nut.
Range of adjustment is within 360 degree
clockwise or counterclockwise.
Press the power switch for 2 seconds to turn on your
X-CAM sight 2. Congratulations! You could now use your
X-CAM sight2. If your sight 2 is Bluetooth version, please
refer to "Paring Bluetooth" on next page to connect your
phone to X-CAM sight 2.
Turn the tilt knob to control the tilt angel of
your phone. Press center of tilt knob to take
photos and videos (Only available for
Bluetooth version)
It is very important to install your phone balanced
on the gimbal. Unbalanced gravity of the phone will
lead to auto-power-off of the gimbal. Please scan
the QR code on the right for a quick guidelines on
how to install your phone and adjust gravity.
6. BLUETOOTH PARING:
Starting up1) - Please activate Bluetooth in your phone after you
have installed your phone balanced on X-CAM SIGHT 2.
2) - Press power button 2 seconds to turn on X-CAM Power on
SIGHT2. Blue light beside the power button flashes dimly,
indicating the gimbal is searching for Bluetooth devices.
3) -Normally, it takes the phone 3 seconds to search forSearch
available Bluetooth devices. Now you will find 'X-CAM SIGHT2'
in devices list. (For 1st time connection, it might read as EFF...)
4) -Select 'X-CAM SIGHT2' and follow the onscreen promptsPAIR
to pair your phone with X-CAM SIGHT 2. Blue LED on the
gimbal lights up constantly if your phone is successfully
connected with X-CAM SIGHT 2.
ATTENTION
X-CAM SIGHT2
X-CAM SIGHT2
Bluetooth Pairing Request
"X-CAM SIGHT2"would
like to pairwith your iphone.
Cancel Pair
X-CAM SIGHT2
1.Gravity of the phone is not
balanced on the tilt or roll
direction. Poor balance leads to
too large current and triggers
overload protection.
2.There is obstruction to the gimbal,
maybe from your phone or collision
while you are shooting. Obstruction
leads to excess resistance and
triggers overload protection.
3.You turn on the gimbal without
phone installed.
4.The handle of the gimbal (the
panel with silver printing logo) is
placed horizontally.
1.Adjust gravity of your phone on
the gimbal before turn on the
gimbal. Make sure your phone
does not tilt to the left or the right,
leans to the front or the back.
2.Properly install your phone to the
gimbal, make sure the phone will
not touch any part of the gimbal
except the phone clipper when
you use it. Do not bump into any
obstruction when you use the
gimbal.
3.You should properly install your
phone on the gimbal before turn
on the gimbal. Otherwise, the
gimbal will activate overload
protection and automatically
shut off.
4.Never place the handle of the
gimbal (the panel with printed
logo) horizontally, or the gimbal
will activate overload protection
and automatically shut off.
1.Power of your gimbal is full.
2.Something is wrong with your
USB charging cable.
1.Your gimbal is non Bluetooth
version, which does not have
Bluetooth function.
2.Your phone has been connected
to other device.
3.Bluetooth version of your phone
is too low.
1.Please buy gimbal equipped
with Bluetooth.
2.Disconnect your phone to
other device first and pair it
with X-CAM SIGHT 2.
3.Make sure Bluetooth version
of your phone is 4.0 or up and
Android version of your phone
is 4.3 or up.
1.Power of your gimbal is full. If
you are still unable to turn on the
gimbal, the reason must be that
gravity of your phone on the
gimbal is still not balanced.
2.Charging cable of the gimbal is
the same with most of the Android
phones. Please compare if the
plugging end is the same, you
could use your Android phone's
charging cable.
I'm
unable
to
charge
the
gimbal.
My
phone
can not
pair with
the
gimbal.
4. TROUBLE SHOOTING
Problem Cause Solution
The
gimbal
is auto
power
off.
5. QUICK START:
