X-Micro mini DisGo User manual

X-Micro mini DisGo
USER GUIDE
V 1.0

1
INFORMATION TO USER
Product Name: X-Micro mini DisGo
Model Name: XST-HU5X / XST-HU2X / XST-HU3X / XST-HU4X
This product is in compliance with the essential
requirements and other relevant provisions of the
FCC (Federal Communications Commission)
Authorized nuder Declaration of Conformity
according to 47 CFR, Part2 , Part15 and CISPR
PUB.22 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a
class B HDD device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.

2
---Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
European COUNCIL DIRECTIVE 89/336/EEC
Low-voltage Directive (73/23/EEC)
This device complies with the specifications listed below:
European Standard EN 55022:1998/A1: 2000 Class B,
EN 61000-3-2:2000
EN 61000-3-3:1995 and EN 55024:1998/A1: 2001 (IEC 61000-4-2:1995,
IEC 61000-4-3:1995, IEC 61000-4-4:1995, IEC 61000-4-5:1995,
IEC 61000-4-6:1996, IEC 61000-4-8:1993, IEC 61000-4-11:1994).

3
Copyright
Copyright 2005 by X-Micro Technology Corp., All rights reserved. No part
of this publication may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language or computer language,
in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of
X-Micro Technology Corp.
Disclaimer
X-Micro Technology Corp. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer
(and not this company, its distributor, or its dealer) assumes the entire
cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, X-Micro
Technology Corp., reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation
to notify any person of such revision or change.
All brand and product names mentioned in this manual are trademarks
and/or registered trademarks of their respective holders.

4
Index
English……………………………………………………………………..5
German……………………………………………………………………7
French……………………………………………………………………..9
Dutch………………………………………………………………………11
Italian……………………………………………………………….…13
Spanish…………………………………………………………………….15
Portuguese…………………………………………………………………..17
Russian……………………………………………………………………….19
Danish……………………………………………………………………… ..21
Swedish………………………………………………………………………23
Norwegian……………………………………………………………………25
Hungarian…………………………………………………………………….27
Traditional Chinese…………………………………………………………29

5
Specification
Product name X-Micro mini DisGo
Capacity 5/20/30/40GB
HDD Toshiba 1.8inch
Bus interface USB 2.0
Transfer rate 480 Mbps
Spin 4200rpm
Power USB self-powered
LED Green for power, Orange for data transfer
Dimension 7 x 60 x 100 mm
Weight 85 g
Electrical +5V, 500mA Max.
OS support Windows ME/2000/ XP
Operating
requirements
Temperature from 0˚C to 50˚C
Relative humidity 5 - 90%
(Non-condensing)

6
Hardware Installation
In order to get the USB 2.0 performance, make sure to properly install the
USB 2.0 driver to your desktop computer or USB 2.0 driver to your
notebook.
Step 1. Connect the USB 2.0 cable connector
to your desktop computer or notebook.
Step 2. Connect the USB 2.0 cable mini
connector to EX HDD housing.
The LED will light after the above steps are
properly installed. Now you can check your file
manager for new external hard disk.
Important Notice
Warranty will overdue if the housing has been opened.
Shock and vibration will damage HDD, try to avoid it!

7
Spezifikation
Produktname X-Micro mini DisGo
Kapazität 5/20/30/40 GB
Festplatte Toshiba 1,8 Zoll
Bus-Schnittstelle USB 2.0
Übertragungsrate 480 Mbit/s
Umdrehung 4200 U/min
Stromversorgung USB-eigenversorgt
LED Grün bei Betrieb, Orange bei Datenübertragun
g
Abmessungen 60 x 98 x 8,5 mm
Gewicht 85 g
Elektrische Daten +5V, 500mA max.
Unterstützte
Betriebssystems Windows ME/2000/ XP
Betriebsanforderungen
Temperatur zwischen 0˚C und 50˚C
Relative Luftfeuchte 5 - 90%
(nicht-kondensierend)

8
Hardware-Installation
Für eine USB 2.0-Leistung muss der USB 2.0-Treiber richtig auf Ihrem
Desktop-Computer oder Laptop installiert worden sein.
Schritt 1. Verbinden Sie den USB
2.0-Kabelstecker mit Ihrem Desktop-Computer
oder Laptop.
Schritt 2. Verbinden Sie den USB
2.0-Kabel-Ministecker mit dem externen
Festplattengehäuse.
Bei richtiger Installation gemäß den obigen
Schritten leuchtet die LED. Rufen Sie jetzt
Ihren Datei-Manager auf, um die neue externe
Festplatte zu erkunden.
Wichtiger Hinweis
Die Garantie erlischt, wenn das Gehäuse geöffnet wird.
Stoß und Erschütterung beschädigen die Festplatte und sollten daher
vermieden werden!

9
Spécification
Nom du produit X-Micro mini DisGo
Capacité 5/20/30/40GB
HDD Toshiba 1.8 pouce
Interface bus USB 2.0
Taux de transfert 480 Mbps
Vitesse de rotation 4200rpm
Alimentation Autoalimenté USB
LED Verte pour l'alimentation, orange pour le
transfert de données
Dimensions 60 x 98 x 8.5 mm
Poids 85 g
Electricité +5V, 500mA Maxi.
Prise en charge OS Windows ME/2000/ XP
Conditions de
fonctionnement
Température entre 0˚C et 50˚C
Humidité relative 5 - 90%
(sans condensation)

10
Installation matérielle
Afin d'obtenir les meilleurs performances USB 2.0, assurez-vous d'avoir
installé correctement le pilote USB 2.0 sur votre ordinateur de bureau ou
sur votre portable.
Etape 1. Branchez le connecteur du câble USB
2.0 sur votre ordinateur de bureau ou votre
portable.
Etape 2. Branchez le connecteur mini du câble
USB 2.0 sur le boîtier du HDD EX.
La LED s'allume une fois les étapes
d'installation ci-dessus effectuées. Vous
pouvez à présent vérifier la présence du
nouveau disque dur externe dans votre
gestionnaire de fichiers.
Avertissement important
La garantie est annulée si le boîtier a été ouvert.
Chocs et vibrations endommagent votre HDD, essayez de les éviter !

11
Specificaties
Productnaam X-Micro mini DisGo
Capaciteit 5/20/30/40GB
HDD Toshiba 1,8inch
Bus-interface USB 2.0
Overdrachtsnelheid 480 Mbps
Omwentelsnelheid 4200rpm
Voeding USB zelf-aangedreven
LED Groen voor stroom, oranje voor
gegevensoverdracht
Afmetingen 60 x 98 x 8,5 mm
Gewicht 85 g
Elektrisch +5V, 500mA max.
Ondersteunde
besturingssystemen Windows ME/2000/ XP
Gebruiksvereisten
Temperatuur van 0˚C tot 50˚C
Relatieve vochtigheid 5 - 90%
(niet condenserend)

12
Hardware-installatie
Om de USB 2.0-prestatie te kunnen gebruiken, dient u het correcte USB
2.0-stuurprogramma te installeren op uw computer of uw notebook.
Stap 1. Sluit de aansluiting van de USB
2.0-kabel aan op uw computer of notebook.
Stap 2. Sluit de mini-aansluiting van de USB
2.0-kabel aan op de behuizing van de EX HDD.
De LED zal oplichten nadat u de bovenstaande
stappen correct hebt uitgevoerd. In het
bestandsbeheer kunt u nu uw nieuwe externe
harde schijf weergeven.
Belangrijke mededeling
De garantie vervalt wanneer de behuizing werd geopend.
Schokken en trillingen zullen de HDD beschadigen. Probeer
dergelijke omstandigheden te vermijden!

13
Specifiche
Nome prodotto X-Micro mini DisGo
Capacità 5/20/30/40GB
Disco rigido Toshiba da 1,8i pollici
Interfaccia Bus USB 2.0
Velocità di
trasferimento 480 Mbps
Giri 4200rpm
Alimentazione Autoalimentato da USB
LED Verde acceso, Arancione trasferimento dati
Dimensioni 60 x 98 x 8.5 mm
Peso 85 g
Caratteristiche
elettriche +5V, 500mA Max.
Sistema operativo Windows ME/2000/ XP
Condizioni operative
Temperatura da 0˚C a 50˚C
Umidità relativa 5 - 90%
(Senza condensa)
Installazione hardware

14
Per avere la velocità delle porte USB 2.0, assicuratevi di installare
correttamente il driver USB 2.0 sul desktop o sul computer portatile.
1. Collegare il connettore USB 2.0 del cavo al
desktop o al computer portatile.
2. Collegare il connettore mini USB 2.0
all’alloggiamento dell disco rigido esterno.
Il LED si accende se l’installazione è stata
eseguita correttamente. Adesso, da risorse del
computer è possibile verificare la presenza di
un altro disco rigido.
Avviso importante
In caso di apertura dell’alloggiamento, la garanzia cessa di avere
validità.
Evitare urti e vibrazioni perché possono danneggiare il disco rigido!

15
Especificación
Nombre del producto X-Micro mini DisGo
Capacidad 5/20/30/40GB
HDD Toshiba 1.8”
Interfaz de buz USB 2.0
Velocidad de
transferencia 480 Mbps
Giro 4200 rpm
Alimentación USB auto-alimentado
Indicador luminoso Verde para energía, naranja para
transferencia de datos
Dimensión 60 x 98 x 8.5 mm
Peso 85 g
Electricidad +5V, 500mA Máx.
Soporte de sistema
operativo Windows ME/2000/ XP
Requerimientos de
operación
Temperatura de 0˚C a 50˚C
Humedad relativa 5 - 90%
(No condensante)

16
Instalación de Hardware
Para obtener el mejor funcionamiento del USB 2.0 asegúrese de instalar
adecuadamente el controlador USB 2.0 en su computadora de escritorio
o el controlador USB 2.0 en su computadora portátil.
Paso 1. Conecte el conector de cable USB 2.0
a su computadora de escritorio o computadora
portátil.
Paso 2. Conecte el mini conector de cable
USB 2.0 a la caja EX HDD.
El indicador luminoso se iluminará después de
haber realizado los pasos anteriores
adecuadamente. Ahora usted puede ver en su
administrador de archivos el nuevo disco duro
externo.
Important Notice
Warranty will overdue if the housing has been opened.
Shock and vibration will damage HDD, try to avoid it!

17
Especificações
Nome do produto X-Micro mini DisGo
Capacidade 5/20/30/40 GB
Unidade de disco
rígido Toshiba de 1,8"
Interface do bus USB 2.0
Velocidade de
transferência 480 Mbps
Rotação 4200 rpm
Alimentação Alimentação por USB
LED Verde para a alimentação, cor-de-laranja
para a transferência de dados
Dimensões 60 x 98 x 8,5 mm
Peso 85 g
Especificações
Eléctricas +5 V, 500 mA Máx.
Sistema operativo
suportado Windows ME/2000/XP
Requisitos de
funcionamento
Temperatura entre 0 ˚C a 50 ˚C
Humidade relativa 5 - 90%
(sem condensação)

18
Instalação do hardware
De forma a poder desfrutar da funcionalidade USB 2.0, certifique-se de
que instala correctamente o controlador USB 2.0 no seu computador
desktop ou no seu Notebook.
Etapa 1. Ligue o conector do cabo USB 2.0 ao
seu computador desktop ou Notebook.
Etapa 2.Ligue o mini conector do cabo USB 2.0
à tomada da unidade de disco rígido externa.
O LED acende após a correcta execução das
etapas acima descritas. Agora já pode aceder
ao gestor de ficheiros do novo disco rígido
externo.
Aviso importante
A garantia perde a validade se a caixa da unidade for aberta.
Os choques e as vibrações podem danificar a unidade de disco rígido,
tente evitá-los!

19
Спецификация
Имя продукта X-Micro mini DisGo
Объем 5/20/30/40GB
Жесткий диск Toshiba 1.8 дюйм
Интерфейс шины USB 2.0
Скорость передачи 480 Mbps
Подача информации 4200 rpm
Питание Безбатарейный USB
СИД Зеленый – питание, оранжевый для
передачи данных
Размер 60 x 98 x 8.5 мм
Вес 85 г
Электропитание +5V, 500 mA Max.
Операционная
система Windows ME/2000/ XP
Условия работы
Температура от 0˚C до 50˚C
Относительная влажность 5 - 90%
(неконденсирующая)