x-net IGC2050F User manual

1 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
XNET Network Box Camera ( IGC2050F )
Install Guide
Ver. 1.0 (101130)

2 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
About this Manual
A compatibility and durability test ensured this product’s high performance.
This installation guide is for XNET Network Box Camera users only, and it describes operations related
to XNET Network Box Camera.
Please read this manual thoroughly paying attention to cautions and warnings before using the
product even if you have used similar products before.
Important Notices
The copyright of this manual is owned by CNB Technology Inc.
It is illegal to copy and distribute this manual without permission.
Damages caused by use of not suggested parts and misuse will not be applicable for support.
Contact the store or the manufacturer immediately if (you think) there is any problem with the
product.
Contact the store or the manufacturer before disassembling the product for alteration or
repair.
XNET is a trademark of CNB Technology Inc.
This product complies for CE (Europe) and FCC (USA) regulations for industrial/home use
electrical device.

3 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
Index
1 . About XNET...................................................................................................................................4
1.1. About XNET..........................................................................................................................4
1.2. Features of XNET..................................................................................................................4
1.3. Applications ..........................................................................................................................4
2 . About the Product .......................................................................................................................5
2.1. Contents...............................................................................................................................5
2.2. Product Information .............................................................................................................5
2.3. Functions and Designations..................................................................................................6
2.3.1. Side View ...................................................................................................................6
2.3.2. Rear View...................................................................................................................7
2.3.3 Connecting to Alarm devices.......................................................................................9
3 . Software Installation...................................................................................................................10
3.1. Connecting XNET to network..............................................................................................10
3.2. Installing IP-Installer Software and Configuring IP address...............................................11
3.2.1. About IP-Installer.....................................................................................................11
3.2.2. Configuring IP Address............................................................................................11
4 . Using Web Viewer.......................................................................................................................13
4.1. Logging In..........................................................................................................................13
4.2. Web Viewer Page................................................................................................................14
5 . Specifications..............................................................................................................................16

4 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
1. About XNET
1
1. .1 1. . A Ab bo ou ut t X XN NE ET T
XNET is an internet based security and surveillance system that is compatible with various network conditions
through easy installation and user interface as well as multi-functional compressor Codec such as MJPEG and
H.264. XNET provides stable real-time surveillance by real time video/ audio at 1080P level, local storage for
any network problems, and hybrid IP technology that can be used with existing analog CCTV devices.
1
1. .2 2. . F Fe ea at tu ur re es s o of f X XN NE ET T
zMost advanced Video/ Audio compression technology (MJPEG/H.264, G.711)
zProgressive technology - Progressive scan makes the image sharp and clear without ghost effect.
zHybrid IP Technology - CCTV analog video output can be used for existing analog CCTV devices.
zTransmission of Multi-Codec stream - Live video signal can be compressed to MJPEG or H.264 and sent to
meet various applications of network or user.
z2-way Audio Communication (Bi-directional voice communication between Client’s PC and XNET)
zSmart Event feature - On the top of motion detection and sensor/alarm feature, pre- and post- alarm
feature allows automated surveillance without an attendant’s monitoring.
zInstall/ Operation Wizard - Install/ Operation Wizard not only makes it easy for installers and users, but
also offers a unified installation setup for massive scale installations.
zUp to 3 motion detection areas
zMotion Detection – Alarm output and Video/ Audio data transmission to FTP site or e-mail upon detecting
amotion.
zSupports Various resolutions - 1080P(1920x1080), SXGA(1280x1024), 720p(1280x720), D1(720x480),
VGA(640x480), CIF(352x240)
zRS-485 interface for Remote Pan/Tilt control
zRemote Control over the network for software upgrade
1
1. .3 3. . A Ap pp pl li ic ca at ti io on ns s
zSurveillance (Building, store, factory, parking lot, financial institutions, government buildings, military
facilities, etc.)
zRemote video monitoring (Hospital, kindergarten, traffic monitoring, remote branch office, weather,
environment preservation, and illegal disposal of trash, etc.)
zReal time broadcasting over the internet (Resort facility, parties, festivals, etc), remote business meetings,
and educational trainings, etc.

5 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
2. About the Product
2
2. .1 1. . C Co on nt te en nt ts s
Please make sure the following contents are included when you open the package.
Contents Description Additional info.
XNET product Network Box Camera (Lens not included)
Auto Iris Lens Plug Connection plug for Auto-Iris control signal
Power adapter and
AC power cord Input: 100~240VAC 50-60Hz
Output : 12VDC, 2A
Terminal Plug 2P * 1ea, 6P * 1ea
Power Jack
CD Software and User’s manual
2
2. .2 2. . P
Pr ro od du uc ct t I In nf fo or rm ma at ti io on n
XNET
(IGC2050F)
Install CD
IP-Installer Viewer Program (XNET-NVR)
Network Camera (Lens not
included) A software that assigns an IP address to the product
A software that monitors and records
Audio and Video signal from the
device (processes up to 16 channels)

6 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
2
2. .3 3. . F Fu un nc ct ti io on ns s a an nd d D De es si ig gn na at ti io on ns s
2
2. .3 3. .1 1. . S Si id de e V Vi ie ew w
Figure 2-1 Network Camera Side view
zLens (Sold separately): C or CS mount/ Fixed or Vari-Focal DC Auto-Iris lens.
zAuto-Iris Control Plug: Plug for Auto-Iris control
The following shows each pin connection:
Strip 8mm of outer jacket of the lens cable, and then strip 2 mm of inner wires to solder them to the
connection plug.
*Please ask at the store about purchasing lens separately.
Auto Iris control plug
1/4”. 20 UNC(20 THREAD)
L : 4.5mm +-0.2mm (ISO standard)
or 0.197”
(
ASA standard
)
CRing
Attach both C Ring and CS
Ring to use C-mount Lens
CSRing
Attach CS Ring only to use
CS-mount Lens
CS Ring Fix Screw
Lens(Sold Separately)
Mountin
g
Screw Hole

7 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
2
2. .3 3. .2 2. . F Fr ro on nt t / / R Re ea ar r V Vi ie ew w
Figure 2-2 Network Camera Front / Rear view
zSTATUS LED : Indicate the status of the product
EVENT LED : If the alarm out is operating, the green LED blinks.
SYSTEM LED : The system operates normally when the blue LED blinks
zMIC : Have built-in microphone.
zLINE IN: Connects to auxiliary Audio Device or microphone. 3.5 mm mono/ stereo audio
connector is used. For connection, refer to the figure below:
Figure2-3.ConnectorforLINEINPUTandAudioLINEOUT
zLINE OUT: Audio signal output to a Power Amplified device or Speaker. This can be used to listen to
the audio signal sent from a remote PC for Bi-directional Audio communication.
zVIDEO OUT: Use this output to monitor the analog video signal while installing.
(Select Video Out at menu screen to enable this output)
zFactory Reset : Press and hold for more than 3 seconds while power is on to recall factory default
settings
LINE IN(mono)
/MIC IN
GROUND GROUND
LINE OUT(mono)
MIC STATUS LED
Factory Reset
Power LED

8 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
zNETWORK : This Ethernet terminal connects to 10Mbps or 100Mbps LAN through an RJ-45 connector.
When optional PoE is used, the power will be supplied from the Network Cable.
LINK : Yellow light indicates that he network is properly connected.
ACT : Green light indicates that the XNET system connected to 100Mbps LAN. This green lamp will
blink if the system receives data.
zSTATUS LED : Indicates the operation status
EVENT LED : Green light indicates that Alarm Out signal is turned on.
POWER LED : Red light indicates that 12V DC power is connected.
zRS-485 and ALARM In/Output Terminal
Pin Description Set up
1 Alarm Out
Select NC/NO at menu screen
2 Alarm Out
3 Alarm In(+)
Select NC/NO at menu screen
4 Alarm In(-)
5 RS485 +
6 RS485 -
RS-485: When properly connected, you can remotely control Pan/Tilt device with RS-485 control
interface.
Alarm In: This connects to an Alarm Sensor signal. Only one sensor can be connected.
Alarm Out: This connects to an external Alarm device that operates by a relay such as Siren
Lamp or Alarm Light. Only one Alarm device can be connected.
zSD CARD SLOT : Enables recording of video data to an external memory device upon occurrence of an
event. Please use less than 16 GB SD Memory.
Figure 2-4. SD CARD
z Power Terminal: Connect 12V DC Power to this terminal.
Do not use this connector when powering up the product through LAN
cable. (PoE) The product is not covered under warranty when it is
damaged by connecting both Ethernet power and 12V DC power to this
terminal.
1 6

9 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
2
2. .3 3. .3 3 C Co on nn ne ec ct ti in ng g t to o A Al la ar rm m d de ev vi ic ce es s
zAlarm Input
Wires from various sensor type (IR, heat, and magnetic) can be connected to Alarm in(+)/(-) terminal as
shown in figure 2.5. (NC or NO of sensor input can be selected at Menu screen.)
Alarm Sensor device requires a separate power source.
Figure 2-5. Connecting to Alarm Input
zAlarm Output
This terminal can only be connected up to AC 30V/400mA or DC 30V/400mA. An additional relay device
has to be used to control higher voltage or current.
InternalCircuitry ExternalCircuitry
Figure 2-6. Connecting to Alarm Output

10 / 17
X
XN NE ET T N Ne et tw wo or rk k B Bo ox x C Ca am me er ra a I In ns st ta al ll l G Gu ui id de e
3. Software Installation
This section provides brief guidelines to install the XNET software quickly and to monitor XNET’s Video and
Audio signals easily. If you have questions about details not explained in this section or if the product is not
functioning as described, please refer to FAQ before contacting the store.
Our homepage is
http://www.cnbtec.com .
3
3. .1 1. . C Co on nn ne ec ct ti in ng g X XN NE ET T t to o n ne et tw wo or rk k
1.A PC or a laptop computer is required to set up an IP address.
zCompatible operating system: Windows 2000/ Windows XP/ Windows Vista
zSince the default IP address of the device is 192.168.123.100, set up the IP address of the
computer like the following: IP Address : 192.168.123.101 Subnet Mask : 255.255.255.0
2.Connect a monitor to VIDEO OUT terminal.
(Select Video Out at Menu screen to enable analog video output.)
3.Connect LAN cable to the Network Terminal of the product.( Use a crossover cable when
connecting it directly to a PC, and use a direct cable when connecting it to a HUB)
4.Connect the camera to the power.
5.Use the Alarm Sensor/ output and audio terminal if necessary.
Crossover Networ
k
Cable
COMPUTER
Direct Network
Cable
COMPUTER
NETWORK HUB