X-Vision XP1080S20 User manual

XP1080S20
Quick Installation High Definition Speed Dome
User’s Manual
Version 1.3

i
Table of Contents
1FEATURES AND FUNCTIONS..............................................................................................1
1.1 General Introduction ...........................................................................................................................................................1
1.2 Features ..................................................................................................................................................................................1
1.2.1 On-Screen Menu ............................................................................................................................................................1
1.2.2 Support multiple protocols...........................................................................................................................................1
1.2.3 Proportional Pan and Tilt .............................................................................................................................................1
1.2.4 On-screen Tips................................................................................................................................................................1
1.2.5 Preset Setup and Call...................................................................................................................................................1
1.2.6 Auto Scan..........................................................................................................................................................................1
1.2.7 Auto Touring.....................................................................................................................................................................1
1.2.8 Auto Pattern......................................................................................................................................................................1
1.2.9 Privacy Masking..............................................................................................................................................................1
1.2.10 Action on Alarm..........................................................................................................................................................2
1.2.11 Auto Flip .......................................................................................................................................................................2
1.2.12 Self-diagnosis.............................................................................................................................................................2
1.2.13 Day/Night Mode (B/W & Color Mode)................................................................................................................2
1.2.14 Auto Focus...................................................................................................................................................................2
1.2.15 Backlight Compensation.........................................................................................................................................2
1.2.16 Pan Tilt and Zoom.....................................................................................................................................................2
1.2.17 3D Intelligent Location.............................................................................................................................................2
1.2.18 Idle Status....................................................................................................................................................................2
1.2.19 Image Stabilizer/Flip.................................................................................................................................................2
1.3 Specifications ........................................................................................................................................................................3
1.3.1 Performance Specifications ........................................................................................................................................3
1.3.2 Technical Specifications...............................................................................................................................................3
2QUICK CONFIGURATION TOOL .......................................................................................... 5
2.1 Overview.................................................................................................................................................................................5
2.2 Operation................................................................................................................................................................................5
3WEB OPERATION....................................................................................................................8

ii
3.1 Network Connection............................................................................................................................................................8
3.2 Login and Logout.................................................................................................................................................................8
4MENU........................................................................................................................................11
4.1 Screen Menu Index.........................................................................................................................................................11
4.2 Self-diagnosis System Information..............................................................................................................................12
4.3 Main Menu............................................................................................................................................................................12
4.4 Menu Operation................................................................................................................................................................13
4.4.1 System Information......................................................................................................................................................13
4.4.2 Display Setting...............................................................................................................................................................14
4.4.3 Camera Setting .............................................................................................................................................................15
4.4.4 Function Setting ............................................................................................................................................................19
4.5 Dome Abnormal Phenomenon Operation............................................................................................................27
4.5.1 Restore to Factory Default Setup............................................................................................................................27
4.5.2 PTZ Movement is not smooth ..................................................................................................................................27
5CABLE CONNECTION ..........................................................................................................28
5.1 System Layout..................................................................................................................................................................29
5.1.1 System Connection......................................................................................................................................................29
5.1.2 Alarm Connection.........................................................................................................................................................29
6FAQ ...........................................................................................................................................30
6.1 Daily Maintenance...........................................................................................................................................................30
6.2 Problems and Solutions...............................................................................................................................................30
7APPENDIX ⅠTHUNDER PROOF AND SURGE PROTECTION.....................................31
8APPENDIX 2 TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS........................32

iii
Welcome
Thankyou for purchasing our product!
This user’s manual is designed to be a reference tool for the operation of your system.
Here you can find information about this speed dome features and functions, as well as a detailed menu tree.
Please keep it well for future reference!
Before installationand operation, please read the following safeguardsand warnings carefully!

iv
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conformto your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation Security
No heavy stress, violent vibration or water splash are allowed during transportation, storage and
installation.
Please use the originalpacking material(or the material ofthe same quality) when you ship it back to
the manufacturer.
3．Installation
Do not apply power to the product before completing installation.
Do not put object on the product.
4．Environment
This series product should be installed in a cool, dryplace away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the device.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
5. Daily Maintenance
Current series product has no power button. Please unplug all corresponding power cables before your
begin installation or daily maintenance work.
Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a
long time.
Do not touch CCD (CMOS) component. You can use the blower to clean the dust on the surface of the
device. You can use the dry cloth with some alcohol or mild detergent to clear if necessary.

v
Do not use the volatility solvent such as the benzene or thinner, or detergent with strong abradibility. It
may result in lens damage or it may adversely affect the device performance.
If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.
6. About Accessories
Always use all the accessories recommended by manufacturer.
Before installation, please open the package and check that all the components are included in the package:
Contact you localretailer ASAP if something is missing in your package.

1
1Features and Functions
1.1 General Introduction
The six-inch megapixel high speed smart network dome camera integrates the functions of network-based
remote surveillance and integrated high-speed smart dome, which makes it convenient to install and easy to
use. This product enjoys a megapixel resolution, which meets the customers' needs for surveillance at HD
level. This product is also qualified with intelligent identification ability, privacy masking settings, alarm
activation, WDR and some other functions. In addition, one can transmit audio/video and control data via
internet in a safe way. Thus, the surveillance is free from the restriction caused by the changes of time and
places to realize a real-time surveillance. With the built-in high-speed PTZ, this product can realize a fast,
accurate fixed-positioning surveillance in a convenient way.
1.2 Features
This series speed dome has the following features:
1.2.1 On-Screen Menu
This series product menu supports multiple languages.
It is easy for you to view dome information and configure dome,camera parameters.
1.2.2 Support multiple protocols
You can use various devices (such as matrix, control keyboard and DVR) and protocols to operate speed
dome.
1.2.3 Proportional Pan and Tilt
This function keeps the image from moving too fast when there is a large amount of zoom.
The quick-installed high definition speed dome continually decreases or increases pan and tilt speeds in
proportion to depth of zoom. When zooms speed is increasing, the camera moving speed becomes slow.
When zooms speed is decreasing, the camera moving speed becomes fast.
1.2.4 On-screen Tips
Here you can view:
Dome title and system version (Software and hardware)
Dome system temperature. (Optional. You can disable this function)
Dome pan/tilt coordinates, preset ID.
1.2.5 Preset Setup and Call
Preset function is to save the address information (such asPTZ pan/tilt, focus and etc) to the memory so
that you can quickly adjust the dome and PTZ to the correct position. This series quick-installed high
definition speed dome supports 255 presets.
1.2.6 Auto Scan
Camera scans back and forth regularly in a horizontal field. Here you need to set left and right limit and scan
speed. You can set 5 scanning paths.
1.2.7 Auto Touring
Add addresses into a routine in a desired order and then set time and stop duration for each address. The
dome will begin an auto touring between these addresses. Each touring path can contain max 32 presets.
1.2.8 Auto Pattern
Memorize dome operation such as pan, tilt, and zoom to repeat. You can call it to repeat the previous
operation.
1.2.9 Privacy Masking

2
Privacy masking is a user-defined, four-sidedarea that can not be viewed by you. The masking area will
move with pan and tilt functionsand automatically adjust in size as the lens zooms.
1.2.10 Action on Alarm
System can connect 7-channel NO/NC input and 2-channel NO alarm output via the socket connector.
Alarms can be individually programmed to initiated pattern, or go to an associated preset, scanning, touring
when received. Dome will return to a previouslyprogrammed state after alarm acknowledgement or to its
previousposition before alarm.
1.2.11 Auto Flip
As long asyou continue to hold the keyboard joystickin the down position, the dome rotates 180 degrees
and repositionsitself for uninterrupted viewing of any subjects that passes directly beneath the dome.
1.2.12 Self-diagnosis
There is a self diagnosis procedure when dome boots up.
Tilt and verticalengine check
Camera diagnostics
Display dome information and diagnosis information such as address, protocol, baud rate, type.
1.2.13 Day/Night Mode (B/W & Color Mode)
Auto/manual switches in low illumination.
Auto: camera will automatically adjust CCD light level.
Manual: use menu or function keys to select day/night mode.
This function needs the speed dome driver (camera) supported.
1.2.14 Auto Focus
Auto focusallows the lens to remain in focusduring zoom-in, zoom-out and motion functions to get vivid
image. You can use FAR or NEAR button to adjust focus manually.
1.2.15 Backlight Compensation
Balance the brightest and darkest sections of a scene to produce a more vivid picture.
1.2.16 Pan Tilt and Zoom
Supports zoom in and zoom out during tilt and pan movement.
In thisperiod focusand iris are both in auto mode to get vivid image.
1.2.17 3D Intelligent Location
Working with DVR, just click part of the currentscene will be displayed in the centralwindow and
automatically zooms. All of these allow you to trace precisely.
1.2.18 Idle Status
When there is no available order, you can use menu to set dome idle status after specified duration. The idle
status includes turn to specified preset or go to scan, tour or pattern function.
1.2.19 Image Stabilizer/Flip
You can enable image stabilizer function and flipin the menu.
When there is vibration, this IS function can guarantee video stability and when flip, you can view video
more clearly.
This function needs speed dome driver (camera) supported.

3
1.3 Specifications
1.3.1 Performance Specifications
1.3.2 Technical Specifications
Built-in
Decode
All digital design. All data are in the connection board. No data loss
when power off occurs.
Integrated design, high stability.
Quick-installed high definition speed dome max support 255
presets. Support 8 auto touring. Each touring max has 32 presets.
Low and medium speed dome max support80 presets.
5 auto scan.
5 auto pattern. Each pattern can max support 400 commands and
the intervalshall be less than 60s.
Built-in direction indicator.
Support max 24 privacymask zones(Depends on the camera type)
7-channel alarminput, 2-channel alarm output.
Built-in PTZ
Fine stepper driver, stable performance, react quickly, precisely
positioning.
Integrated design, tight structure.
Elegant mechanical driver device. Support 360 degrees continuous
rotation, no monitor blind spot.
0.1°/s rotation speed while maintain stable image.
180 degrees tilt continuous monitor.
Built-in zoom
lens, high
sensitive,
high
resolution
integrated
digital
process
color
camera.
Auto focus
Auto BLC
Auto brightness control
Auto white balance
Auto day/nightswitch (Auto B/W & color switch)
OSD
Preset title display
View dome initial setup information
Modify camera parameter
Set preset
Set auto scan
Set auto patter
Set 2-channel alarminput and 1-channelalarmoutput.
Set auto day/night switch (Auto B/W & color switch)
Set privacy mask zones

4
Power
It depends on the product your purchase.
Camera Driver
Consumption
12W
Decoder
Built-in
Engine
Stepper motor
Preset
255(In PELCOD, PELCOP protocol).
80 (In industrialprotocol)
Please note the value may vary due to different protocols.
Auto Tour
8
Auto Pattern
5
Auto Scan
5
PrivacyMask
8 zones in one-window.
The different series products support different amount. It
depends on the camera type.
Alarm Input/Output
7-channel alarm input and 2-channel alarm output. (Default
setup is 2-channel alarminput and 1-channel output.)
Information
Time, address, dome title, dome coordinates, temperature,
alarm and etc.
Lens
Adjust speed in accordance with lens
Auto Rotation
Tilt 92ºauto rotates to pan 180 º
Auto Pan
0 º -360ºcontinuously
Manual Pan Motion
Speed
0.1º—300º/S
Preset Maximum
Speed
400º
Manual Tilt Motion
0.1º—120º/S
Manual Tilt Scan
Section
0º—180º
PTZ Scan Accuracy
0.06 ± 0.015º
Signal Format
PAL/NTSC (Camera mode)
S/N Ratio
> 50dB
Humidity
＜90%
Environment
-40℃—60℃（outdoor）

5
2Quick Configuration Tool
2.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it
to upgrade the device.
Please note the tool onlyapplies to the IP addresses in the same segment.
2.2 Operation
Double click the ‘”ConfigTools.exe”icon, you can see an interface is shown as in Figure 2-1.
In the device list interface, you can view device IP address, port number, subnet mask, default gateway,
MAC address and etc.
Figure 2-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 2-2.
Figure 2-2
Select the “Open Device Web”item; you can go to the corresponding web login interface. See Figure 2-3.

6
Figure 2-3
If you want to modify the device IP address without logging in the device web interface,you can go to the
configuration tool main interface to set.
In the configuration tool search interface (Figure 2-1), please select a device IP address and then double
click it to open the login interface. Or you can select an IP address and then click the Login button to go to
the login interface. See Figure 2-4.
In Figure 2-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 2-4
After you logged in, the configuration tool main interface is shown asbelow. See Figure 2-5.

7
Figure 2-5
For detailedinformationand operation instruction of the quick configuration tool, please refer to the
Quick Configuration Tool User’s Manual includedin the resources CD.

8
3Web Operation
This series product supports the Web access and management via PC.
Web includes severalmodules: live view, PTZ, set, alarm, logout and etc.
IP camera factory default setup:
IP address: 192.168.1.108.
User name: admin
Password: admin
3.1 Network Connection
Please follow the steps listed belowfor network connection.
Make sure the IPC hasconnected to the network properly.
IPC IP addressand PC IP address shallbe in the same network segment. IPC default IP address is
192.168.1.108. If there is router, please set the corresponding gateway and subnet mask.
Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.
3.2 Login and Logout
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address bar.
See Figure 3-1.
Figure 3-1
System pops up warning information to ask you whether install control webrec.cab or not. Please click OK
button, system can automatically install the control. When system is upgrading, it can overwrite the previous
Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the
control download. Or you can lower the IE securitylevel. See Figure 3-2.
Input your IP
address here

9
Figure 3-2
After installation, the interface is shown as below. See Figure 3-3.
Please input your user name and password.
Defaultfactory name is admin and password is admin.
Select the network connection type.
The login type includes: TCP/UDP/Multicast.
Note: For security reasons, please modify your password after you first login.
Figure 3-3
After you logged in, you can see the main window. See Figure 3-4.

10
Figure 3-4
Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.

11
4Menu
4.1 ScreenMenuIndex
Note:
ERR means current setup is invalid.
…means there is submenu.
INITIAL INFORMATION…
ADDR INFORMATION…
SYSTEM TIME SETTING…
SET NORTH
LANGUAGE ：ENGLISH
FACTORY DEFAULT
RESTART
BACK
EXIT
PRESET TITLE : ON(ON/OFF)
AZIMUTH DISP : ON (ON/OFF)
TIME DISP : OFF (ON/OFF)
POSITION : OFF (ON/OFF)
ZOOM DISP : OFF (ON/OFF)
INSIDE TEMP : ℃(℃/F/OFF)
TITILE DISPLAY :OFF
BACK
EXIT
DISPLAY SETTING
SYSTEM
INFORMATION
CAMERA SETTING
FUNCTION SETTING
EXIT
WB SETTING
EXPOSURE SETTING
DAY/NIGHT SETTING
PICTURE ADJUST
FOCUS SETUP
ZOOM SPEED : 08 (01-08)
APERTURE : 06 (01-16)
NEXT PAGE
BACK
EXIT
PRESET
AUTO PAN
AUTO SCAN
CRUISE
PATTERN
IDLE MOTION
AUTO RUN
NEXT PAGE
BACK
EXIT

12
ADDR ：
BAUD RATE ：
PARITY ：
PROTOCOL
SOFTWARE ：V1.04.3
SYSTEM INFORMATION
DISPLAY SETTING
CAMERA SETTING
FUNCTIONSETTING
IR LIGHT SETTING
EXIT
The above diagram illustrates the overall structure of the speed dome setup menu.
Note:
ERR means current setup is invalid.
Please make sure all the cable connections are right.
4.2 Self-diagnosis System Information
After installation,please connect speed dome to power. The system goes on a self-diagnosis, and then it
pops up the above interface to show the system information.
If there is anything wrong during the self-diagnosis, systempops up error code.
The above interface disappears after speed dome received the first command (or the display time lasts for 4
minutes.)
ADDR: Here you can view dome address information. For example, 001-H, 1 is the address number, -H
is hard address mode. –S is software address mode.
Baud rate: Dome communication baud rate.
Parity: Communication parity bit format.
PROTOCOL：System can auto recognize industrialprotocol, PELCOD, PELCOP.
Software: Dome software version of the control firmware.
When you are using the control keyboard or the matrix host to control the device, please make sure
the control parameter of the keyboard or the matrix host is the same with the speed dome OSD
(including address,baud rate, parity). Please make sure the cable connection is OK.
4.3 Main Menu
You can open the IP dome menu via monitor platform, Web, control keyboard, matrix, or speed dome
controlterminal.
SYSTEM INFORMATION：Dome self-diagnosis information, address information, system time setup,
set north direction, language, factory default setup, reboot and so on.
DISPLAY INFORMATION: Display dome preset title, azimuth display, time, direction, dome internal
temperature and etc information.
CAMERA PARAMETERS：Display dome white balance setup, camera function setup, day/night setup,
shutter setup and etc.
FUNCTION SETTING: Set preset, pan, scan, auto cruise, pattern, idle motion, time task and privacy mask
function.
EXIT: Log out the systemmenu.

13
INITIAL INFORMATION
ADDR INFORMATION
SYSTEM TIME SETTING
SET NORTH
LANGUAGE : ENGLISH
FACTORY DEFAULT
RESTART
BACK
EXIT
ADDR ：001-H
BAUD RATE ：9600
PARITY ：NONE
SOFTWARE ：vX.XX.XX
BACK
EXIT
4.4 MenuOperation
In the speed dome main menu, you can use the left/right button on the keyboard or in the speed dome
terminal menu to configure the system menu. Before setup, please move the cursor to the current item you
want to configure.
In main menu, please click confirm button to go to the sub menu or use left/right key to configure setup.
Use up/down button to select back option and then click confirm button to go back to the previous menu.
Use up/down button to select exit option and then click confirm button to log out system menu.
All setup here will notlose when encounter power failure.
4.4.1 System Information
INITIAL INFORMATION: Move the cursor to INITIAL INFORMATION and then click confirm button to go
to the third submenu.
ADDR INFORMATION: Move the cursor to SITE INFORMATION and then click confirm button to go to
the third submenu.
SYSTEM TIME SETTING: Move the cursor to SYSTEM TIME SETTING and then click confirm button
to go to the third submenu.
SET NORTH DIRECTION: Set dome benchmark direction so that you can know the angel between the
benchmark and then current location. Please move the cursor to the option and then click confirm
button untilyou see O.K. Now you have set north direction.
LANGUAGE: The dome menu language. There are several languages for you to select. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
FACTORY DEFAULT: Restore dome factory defaultsetup.Please move the cursor to the option and
then click confirm button until you see O.K. Now you can see the IP dome begin rebooting to restore
factory default setup.
RESTART: Reboot the speed dome.
BACK: Go back to the previous menu.
EXIT: Log out system menu.
4.4.1.1 Initialization information
Move the cursor to INITIAL INFORMATION and then click confirm button, you can see the above interface.
Here you can view dome basic information.

14
4.4.1.2 Address Information
Move the cursor to SITE INFORMATION and then click confirm button.
ADDR TYPE: There are two options: soft and hard. Please use the left/right button on the keyboard or
in the speed dome terminal menu to set. Please click the OK button to confirm
ADDR-HARD: It is an address you set in the dialswitch. You can not modify it through software.
ADDR-SOFT: You can set address via software. It is to say, you can use menu to modify dome address.
The value ranges from 1 to 255.
BACK: Go back to the previous menu.
EXIT: Log out system menu.
4.4.1.3 System Time Setting
Move the cursor to SYSTEM TIME SETING and then click confirm button, you can go to the third
submenu. Please use the left/right button on the keyboard or in the speed dome terminal menu to set.
After completed setup, please click confirm button to save current setup. After you see speed dome
menu displays OK, you can see the setup is valid now.
4.4.2 Display Setting
Move the cursor to DISPLAY SETUP and then click confirm button, you can go to the third submenu. Please
use the left/right button on the keyboard or in the speed dome terminal menu to set. After completed setup,
please click save button to save current setup.
PRESET TITLE: Display dome preset title or not. Please use the left/right button on the keyboard or in
the speed dome terminal menu to set. You can go to Function Setup->Preset section to set
corresponding preset value and preset title.
AZIMUTH DISP: Display dome current coordinates or not. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set
TIME DISP: Display dome system time or not. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
ADDR TYPE : HARD
ADDR-HARD : 001
ADDR-SOFT : 001
BACK
EXIT
PRESET TITLE ：ON
AZIMUTH DISP ：ON
TIME DISP ：OFF
POSITION ：OFF
ZOOM DISP ：OFF
INSIDE TEMP ：℃
TITLE DISP ：OFF
BACK
EXIT
YEAR : 2009
MONTH : 001
DATE : 017
WEEK : SUNDAY
HOUR : 013
MINU：: 052
SAVE
BACK
EXIT