Honeywell HSD-361P User manual

HSD-361P Operation Manual
VISTA Series HSD Speed Dome
Read this Manual carefully before installation and keep it by hand for future reference.

CAUTION
Persons without technical qualifications should not attempt to operate this dome device before reading this Manual
thoroughly.
Remove any power to the dome before attempting any operations or adjustments inside the dome cover to avoid potential
damage to the mechanism.
Inside the dome cover there are precision optical and electrical devices. Heavy pressure, shock and other sudden
adjustments or operations should be avoided. Otherwise, you may cause irreparable damage to the product.
Please do not remove or disassemble any internal parts of the video camera to avoid normal operation and possibly void the
warranty. There are no serviceable parts inside the camera.
Please connect all the wires of the dome strictly accordingly to the specifications. It is highly recommended that the proper
lightning arrestors and surge suppressors are installed before the dome is entered into service.
Please do not use the product under circumstances where the limits exceed the maximum specified temperature, humidity
or power supply specifications.
Suggest using UPS or other stable power supply system to make sure camera system can work normally.
1

Table of Contents
Cautions ……………………………………………1Auto AF…………………………………………18
Package contents……………………………………1 Auto AE…………………………………………18
Chapter One – Introduction…………………………1 Vector Scan AF ………………………………18
1.1 Performance Characteristics…………………1 VectorScanStill…………………………………18
1.2 Features and Functions ……………………1 4.5 Diagnostic Options ……………………………18
Chapter Two – Camera installation ………………2 Clear Memory …………………………………18
2.1 Important Safeguards ………………………2 Restore Def Setting ……………………………18
2.2 Package Contents ……………………………3Color System……………………………………19
2.3 Camera Installation……………………………4Dome Information………………………………19
2.4 Camera Shroud installation…………………54.6 Camera Options ………………………………19
2.5 Bracket installation……………………………5Camera Name……………………………………20
2.6 Installation of the acrylic dome cover…………7Zoom and Focus ………………………………20
2.7Wiring Specifications……………………………8Camera Exposure ………………………………21
Chapter Three Basic Configuration ………………9 MaskZone………………………………………22
3.1 Wiring……………………………………………9MaskColor………………………………………22
3.2 Protocol and baud rate setting…………………10 Others……………………………………………23
3.3 Address setting of each dome…………………11 4.7 Function Programming ………………………22
3.4 Controller setting………………………………11 PTZTour ………………………………………22
Chapter Four Menu setting ………………………12 ProgramVectorScan……………………………23
4.1 Operation instruction ………………………12 Annex: Short-cut operations and specification
Main Menu……………………………………12 of Dome device ……………………………24
Number Programming Instruction………………12 Short-cut operation table ……………25
4.2 Main Menu ……………………………………12 Product Specifications…………………26
4.3 Display Options ………………………………13 Lightning arresters and Surge
PreShot …………………………………………13 Suppressors ………………………………27
Setting of Sector…………………………………15
Coordinates ………………………………………17
Crosshairs…………………………………………17
Start-Up Scr Msg…………………………………17
4.4 Control Options …………………………………17
Set Pan and Tilt……………………………………17
Set Default Function………………………………18
Speed Limit ………………………………………18
Auto Flip …………………………………………18
1

Package Contents
Please check the quantity of the package contents when open the carton.
Description Qty
Manual, Certificate each1
BNC Wire 1
Rubber Cushion 1
Lower housing of dome 1
Bag of screws 1
High Speed Dome 1
Camera Module 1
Wall bracket 1
AC24V transformer 1
Camera Shroud 1
Terminal 2
Please contact the distributors in time if the spare parts are missing.
1

Chapter One – Introduction
1.1 Performance Characteristics
0～255 individually addressed units. The dome address is defined using a dip switch with 8 positions (Binary addressing
scheme).
Integrated multi-protocol and auto protocol differentiation. Note: The dome can auto differentiate the protocol of the
controller only on power up.
Continuous Pan 360 degree rotation.
90 degree Tilt action plus 2 degree angle adjustment (the view angle can be 90 or 92 degrees).
Pan speed in manual operation is variable from 0.1 up to 300 degrees per second.
Tilt speed in manual operation is variable from 0.1 to 120 degrees per second.
128 preset positions (A preset position is defined as a user definable setting for precise coordinates).
The maximum speed when a preset position is called can reach 400 degrees per second with positioning accuracy of±0.1
degree.
Input power supply: 24VAC-2Amp (outdoor).
User friendly on screen menu interface for ease of installation.
Environmental protection conforming to IP66 standards (outdoor model).
RS-485 (long distance) communications mode.
Selectable transmission speed, (i.e. Baud rate) .User definable via dip switch setting from 2400bps to 1920 bps.
1.2 Features and Functions
Multi-language on screen menu for operation and function settings.（The camera title is user definable as well as the ability to
display or not the camera coordinates）.
On screen Crosshair function (By enabling this option, the target can be followed more effectively using the crosshairs as a
reference point).
Three users define PTZ tours with up to 2 minutes record duration for each tour. (User has the ability in real-time to monitor
and record the action of a manual dome operation).
Six group of programmable vector scans (including scan speed, dwell time, preset and dwell time between tours) Auto flip
function in tilt action + 10 degree positioning.
24 sectors of user programmable privacy zones (sectional mask). User can mask part of the camera sectors which differs
between different models of installed cameras.
Eight sectors of user programmable sectional display. User can define and display the name and position of the camera,
which differs between different models of installed cameras.
Resume automatic operation after initial self-test of the dome as well as resume automatic operation when there is no
transmission from a keyboard controller (Dwell time can be set from 1 to 999 seconds).
Freeze frame function (snapshot function availability supported by camera).
Resume operation function (Dome unit will return to the previous operation after the execution of an operation using the on
screen menu).
Intelligent manual scan function (By executing this function in manual pan, you can adjust the manual pan behavior of the
dome). 1

Intelligent power off real time memory (Should power fail while the dome was in operation, the dome well resume its
preprogrammed function upon power restores).
Highly efficient 3-dimensional scan function (User can change the pan scan tour when the dome is in manual scan or auto
scanbetweentwopanpoints).
Zoom and dome speed correction function (When the zooming-in of the camera is disabled, the dome speed is reduced to
allow for precise operation control).
Chapter Two – Camera installation
2.1 Important Safeguards
2.1.1 Read this Manual and Intelligent Camera Operation Guideline before attempting installation or operation of dome
device(This manual will be subject to revision without further notification).
2.1.2 Power supply: AC24V.The input voltage of the dome is indicated on the bottom of the dome device or on the input
position.
2.1.3 Inside the dome cover there are precision optical and electrical devices.
Heavy pressure, strong shaking and other sudden adjustment or operations should be avoided
during the transportation. Otherwise, you may cause irreparable damage to the product.
2.1.4 Please DO NOT remove or disassemble any internal parts of the video camera to avoid
normal operation and possibly void the warranty.
2.1.5 During usage, user should abide by all electrical safety standards.
Use only the power supply specified by manufacturer. The control cable
for RS485 communications as well as the video signal cables should be
isolated from high voltage equipment and or high voltage cables.
It is highly recommended that the proper lightning arresters and surge
suppressors are installed before the dome is entered into service.
2.1.6 Indoor dome is for indoor use only and not suitable for outdoor or
high humidity ratings. Use outdoor dome for high humility location or in the rain.
2.1.7 Please do not use the product under circumstances where the limits
exceed the maximum specified temperature, humidity or power supply specifications.
2.1.8 Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged period of time.
2.1.9 Cleaning agent of abrasion should not be used to clean the dome device.
Use a piece of dry cloth to clean and dry the device.
2.1.10 Use the camera carefully to avoid striking or shaking.
2.1.11 Verify that the surface you are planning to use for attaching the dome
can adequately support the weight of the device and mounting hardware.
2.1.12 Should the lens of the camera become dirty, use special lens cleaning cloth and solution to properly clean it.
2

2.2 Package Contents
2.2.1 Below figures illustrate the package contents.
Figure 1. Illustrates the upper layer of the carton (top half), Figure 2. Illustrates the lower layer of the carton (bottom half).
Fig1 Fig2
Sequence No. Description
1 Manual, Certificate
2 BNC Wire
3 Rubber Cushion
4 Lower housing for the dome, Terminal
5 Bag of Screws
6 High Speed Dome
7 Camera Module
8 Wall bracket
9 AC24V transformer
10 Camera Shroud
3
2
3
4
5
6
7
8
1
9
10

2.3 Camera Installation
2.3.1 Ribbon cable：Insert FPC socket of the cable to the relevant port of the base plate on the dome control board. (Ribbon
cable has length of 65MM and 110MM, user can select the ribbon cable according to different models of the camera) Figure 4
below illustrates the writing configuration of the ribbon/cable.
FPC
Connector
FPC
Connector
FFC
FlexibleFlat Cable
4-PWM2*6
Fig.3
Fig.4
Output of ribbon cable
Insert the camera ribbon to
the camera FPC socket to
secure the connection.
Fig.5
2.3.2 Install the camera module: Install the camera module on the vertical axis tray of the dome as
illustrated in Fig. 6 and Fig. 7.
Attention: Take care not to scratch the lens when installing the camera. Do make sure the camera model is the right one
for installation. Secure the camera to the corresponding screw holes as illustrated in Fig. 6, according to the model and
make of the camera, as different camera models may have different dimensions. Following the installation of the camera
module verify that it does not touch any of the dome parts including the camera shroud and acrylic dome by gently
moving the camera module along the vertical axis.
Fig.6 Fig.7
Sony camera model screw holes
Install the camera module on the vertical
axis tray of the dome as illustrated in Fig.7
using the 4 supplied PWM2*6 Screws.
Honeywell camera model
screw holes
4

2.4 Camera Shroud installation
Fig.8 illustrates the location of the 4 screw holes for the camera shroud (M3).
Fig.8 Fig.9
Screw holes
Tighten the screws
Fig.10 Fig.11
2.4.1 Position the open end of the camera shroud towards the camera lens as illustrated on Fig. 9. Align the 4 holes of the
shroud with the 4 holes on the core of the dome as illustrated in Fig. 10.
2.4.2 Utilizing the supplied (4) four M3*14 screws securely tighten the camera shroud in place, as illustrated in Fig. 11.
2.5 Bracket installation
2.5.1 Feed the BNC wiring harness through the channel inside the wall bracket as illustrated in Fig 12.Ve r i f y t h a t t h e
channel remains empty before feeding the wiring harness.
Feed the BNC
Wiring from here
4-M6 ex
p
and screw
Fig.12 Fig.13
2.5.2 Affix the wall bracket to the wall using 4 M6 Expand screws as illustrated in Fig 13.
5

Fig. 14 illustrates installation of wall bracket Fig 15 illustrates installation of pendent bracket
4-M8
Silica gel
Silica gel
Bracket adapter
Wal l bracket
Fig.14 Fig.15
Fig. 16 illustrates installation of pole bracket
4-M8
4-M8
Silica gel
Fig.16
6

2.6 Installation of the acrylic dome cover
The Way of installation is to rotate the acrylic dome cover. Caution should be exercised when handling the
clear dome by wearing the cotton glove so as to prevent any abrasions or scratches to the surface as this
will affect the optical performance of the camera.
Installation instruction
1. Carefully align the two parts and slowly rotate counterclockwise as illustrated in Fig. 17.
2. Remove the protection film as illustrated in Fig.18.
Fig.17
Align the two parts and rotate
clockwise as indicated
Remove the protection film
Fig.18
7

2.7 Wiring Specifications
Fig. 19 is the illustration of the wiring diagram for the electrical connections to the dome unit.
Fig. 20 illustrates the supplied power supply.
图1 9
黄绿相间:接大地
视频输出
黑色
红色
AC24V 电源
黄色：RS485-
橙色：RS485+
黄绿相间：接大地
接控制键盘
BNC Connector：Video output
Orange：RS485+
Yellow：RS485-
Red，black：AC24V power supply
Terminal：Connect to the dome device
Yellow/green：Ground wire
Connect to keyboard
controlle
r
Yellow/green：Ground wire
Fig.19
AC 24V Power Supply
Connect 220V power supply
Connect to dome
Fig.20
8

Chapter Three – Basic Configuration
3.1 Wiring
User can understand the dome electric connection property and adjust, assemble, test and operate the device on
show with convenience.Please read the wiring illustration carefully for the first time use.Any wrong connection
may cause the permanent damage of the dome or other equipments.
Yellow/green：Ground wire
BNC Connector：Video output
Orange：RS485+
Yellow：RS485-
Red，black：AC24V power supply
Terminal：Connect to the dome device
Yellow/green：Ground wire
Connect to keyboard
controlle
r
Caution: This operation should be performed with the power OFF.
Yellow/green：Ground wire
BNC Connector：Video output
Orange：RS485+
Yellow：RS485-
Red，black：AC24V power supply
Terminal：Connect to the dome device
Yellow/green：Ground wire
Connect to keyboard
controlle
r
Caution: This operation should be performed with the power OFF.
9

Yellow/green：Ground wire
Terminal：Connect to the dome device
Yellow/green：Ground wire
BNC Connector：Video output
Orange：RS485+
Yellow：RS485-
Red，black：AC24V power supply
Connect to keyboard
controlle
r
Caution: This operation should be performed with the power OFF.
Before installation and use, the unique address for each dome and the communication protocol including transmission
speed (baud rate) should be set to correspond with the chosen control system.
3.2 Protocol and baud rate setting (Caution: This operation should be performed with the power OFF.)
ON
123456
Protocol and baud rate
On/Off
Protocol setting Baud rate setting
On/Off
Protocol type
1st 2nd 3rd 4th 5th 6th
PELCO-D ON ON OFF OFF ** **
PELCO-P OFF OFF ON OFF ** **
Auto Detect OFF OFF OFF OFF ** **
Kd6 ON ON ON ON ** **
VCL OFF OFF ON ON ** **
Max Pro ON OFF ON ON ** **
CAUTION: The protocol and baud rate of dome device should match the settings of the controller. In order to
take effect the dome must be power cycled after each change.
10

On/Off
Baud rate 5th 6
th
2400 OFF OFF
4800 OFF ON
9600 ON OFF
19200 ON ON
3.3 Address setting of each dome ( Caution: This operation should be performed with the power OFF.）
Setting method: The sum of switch numbers when it is at ON position is the address of dome device.
Calculation example of dome device address: (2+4+16=22), the address is 22.Dome device range: 0 ～255
128
64
32
16
1
2
4
8
ON
1 2 3 4 5 6 7 8
2 4 1 6
ON
1 2 3 4 5 6 7 8
3.4 Controller setting
Set the protocol, baud rate, and address of the keyboard controller to match the settings on the dome.
(For instruction of how to set the keyboard communication settings please refer to keyboard controller manual).
Attention: If the protocol setting of the dome is set to auto detection, the protocol of keyboard controller can be
set PELCO-D or PELCO-Parbitrarily.But its baud rate should be set identical with that of the dome device.
When all of the above settings are completed you can start testing to dome functionality.
Up
Right
Left
joystick
Down
Zoom in
Zoom out
Rotating
joystick
11
The operation of the dome and the direction (up, down, left
controlled usingand right) of the camera can be the ystick
Summary: The camera and they are basically normal.
jo
of the keyboard controller, as illustrated above.
This figure shows protocol of
PELCO-D, Baud rate of 2400.
ON
16
5432
On/Off switch and
matchin
g
numbers
On/Off switch and
matchin
g
numbers
matching
matching
matching matching matching
Zoom control of the camera can be achieved by
rotating the knob on the joystick or by using TELE
(zoom in) and WIDE (zoom out) functions on the
Summary: The dome device is basically normal.
keyboard controller as illustrated above.

Chapter Four – Menu setting
struction
a selection, move the joystick in the UP or DOWN direction. The on-screen arrow points to the selected
o the Left or Right position you can change the value of your selection or enter the
4.1 Operation in
Menu operation
To make
option.
Press OPEN or use the joystick t
submenu for the selected option.
Press CLOSE to exit menu or return to the previous menu.
Number
1. Joystick Left or Right to move the cursor under the desired numeral position.
2. Press OPEN to confirm.
3. Move the joystick Left or Right to move the cursor to select the desired number.
4. Press OPEN to confirm the selection, and the selected number will show on the corresponding position.
5. Input other Characters accordingly.
6. Press CLOSE to finalize your selection and return to the previous menu level.
4.2 Main Menu
Select“90”on the preset position to enter the
main config
Different options of language are available.
and setup the PreShot position on the menu.
uration menu for the dome.
1. n to enter the main
2. or Down direction.
Select “90 ”on the preset positio
configuration menu for the dome.
To make a selection move the joystick in the Up
The on-screen arrow points to the selected option.
Press OPEN or move the joystick Left or Right you can enter the
submenu f
-- - - - -- - - - - - - HSD - - -
or the selected option or change the value of your
3. yboard controller to exit menu
selection.
Attention: The function of the button“OPEN”is IRIS OPEN.
Press the button CLOSE on the ke
→h
6. Funct
IRIS CLOSE to Exit
1.Language Englis
2. Display Options
3. Control Options
4. Diagnostic Options
5. Camera Options
ion Programming or return to the previous menu.
Attenti The function of the button “CLOSE” is IRIS CLOS.on:
Language Setting Display Options
PreShot Position setting is to setup dome information
display
-
→nglish
- - - - - - - HSD - - - - - - - - Display Options
→
5. Start-U
IRIS CLOSE to Exit
1.Language E
2. Display Options
1. PreShot Setup
2. Sector Setup
3. Coordinates ON
4.Crosshair Off
p Scr Msg ON
3. Control Options
4. Diagnostic Options
5. Camera
Options
ion Programming6. Funct
IRIS CLOSE to Exit
12

Control Options Diagnostic Options
Set the dome in manual or auto operation Data information management setup.
ontrolling sy idual setting.
amera function Setup. ProgramandexecutethePTZTourandVectorScan.
ay Options
umbe
13
and make its tilt and pan action as well as
Diagnostic Options
→
4. Dom
IRIS CLOSE to Exit
the camera to be compatible with the whole
c stem and user indiv
Control Options
→
Scan
1. Set Pan and Tilt
2. Set Default Function
3.SpeedLimit ON
4.AutoFlip ON
5.AutoFocus PTZ
6.AutoAE PTZ
7. Vector Scan AF OFF
8. Vector Still OFF
IRIS CLOSE to Exit
Camera Options Function Menu
C
1. Clear Memory
2. Restore Def. Setting
3. Color System PAL
e Information
Camera Options
4.3 Displ
PreShot
N r
→
Name
5. Mas
IRIS CLOSE to Exit
1. Camera Exposure
2. Camera
3. Others
4. Mask Zone
k Color
There are two methods to set up the PreShot Position:
1: Setup and c
Function Programming
→
2. Program
IRIS CLOSE to Exit
1.PTZTour
Vector Scan
PreShot Name
→1
5.
IRIS CLOSE to Exit
1.Number
2. Set PreShot
3. Call PreShot
4. Delete PreShot
Name_________
all the PreShot on the controller (Keyboard/DRD/Matrix) of
2: Setup and call the PreShot on the menu controlled by the dome.
the dome.
1 - 165
1
↑
0 1 2 3 4 5 6 7 8 9
IS CLOSE When Done
1 - 165
1
↑
2 3 4 5 6 7 8 9
IS CLOSE When Done
0 0
IR
0 0
0 1
↑
IR

PreShot Setup
Call PreShot
Delete PreShot
→2. PreShot Setup
3. Call PreShot
4. Delete PreShot
5. Name _________
IRIS CLOSE to Exit
+
IRIS CLOSE When Done
Pan: 262.2 Tilt: 2.7 X8
+
Stored
Pan: 262.2 Tilt: 2.7 X8
PreShot Name
1.Number 1
2. PreShot Setup
→3. Call PreShot
4. Delete PreShot
5. Name _________
IRIS CLOSE to Exit
Call PreShot on the menu:
1. Move the joystick Left or Right or press OPEN to enter Number Editing
and select the desired PreShot Position.
2. Move the joystick Left or Right to move the cursor to edit the digit number,
Press OPEN to confirm. Press CLOSE to finalize your selection and exit.
3. Move the cursor to select the Call PreShot Position.
4. Move the joystick Left or Right or press OPEN to call the PreShot Position.
5. Press CLOSE to exit.
PreShot Name
1.Number 1
2. PreShot Setup
3. Call PreShot
→4. Delete PreShot
5. Name _________
IRIS CLOSE to Exit
Delete Preset Position on the menu:
1. Edit the number to be deleted (Refer to Number Input Instruction)
Note: Select the PreShot to be deleted.
2. Move the cursor to select the Deleted Position.
4. Move the joystick Left or Right to enter the deleting position.
5. Press OPEN when done. Press CLOSE to exit.
Are you sure to do this?
IRIS OPEN to Confirm
IRIS CLOSE to Cancel
PreShot Name
1.Number 1
7. Move the joystick Left or Right or press OPEN to enter.
8. IRIS CLOSE When Done. When SAVED is displayed on the screen, return to the
menu.
6. Move the cursor to setup PreShot Position.
(0-9)Press OPEN to confirm the selection. Press CLOSE to finalize your
selection and exit.
5. Move the joystick Left or Right to move the cursor to edit the digit number.
4. Move the joystick Left or Right or press OPEN to enter Number Editing.
Note: Edit the Number on the PreShot.
3. Move the joystick Left or Right or press OPEN to enter PreShot Options.
1. Move the joystick Left/Right or press OPEN to enter Display Options.
2. Move the joystick Left/Right to move the cursor to select the PreShot Options.
Setup the preset position on the menu
14

PreShot Name
Sector Setup
Number
PreShot Name
1.Number 1
2. PreShot Setup
3. Call PreShot
4. Delete PreShot
→5. Name _________
IRIS CLOSE to Exit
Edit PreShot Name
1. Ref<number input instruction>edit PreShot name.
2. Move the cursor to select PreShot name.
4. Move the joystick Left or Right or press OPEN to enter Name
and Character Editing Menu.
0 3 6 3
↑
IRIS CLOSE
When Done
PreShot Name
→6. Name Display Off
IRIS CLOSE to Exit
On/Off Setting on the PreShot Name
1. Move the cursor to select Name Display.
2. Move Left or Right or press OPEN to enter
On/Off Name Display.
0 3 6 3
↑
0 1 2 3 4 5 6 7 8 9_
IRIS CLOSE When Done
Sector Setup
→1.Number 1
2.Name
3. Pan Start POS 0.0
4. Pan End POS 0.0
5. Tilt Start POS 0.0
IRIS CLOSE to Exit
1. Move the joystick Up or Down to move the cursor to select Sector Setup.
2. Move the joystick Left or Right or press OPEN to enter.
3. Select Number, move the joystick Left or Right to select the number.
15

Sector Name
Pan Start POS
Pan End POS
Tilt Start POS
Sector Setup
1.Number 1
→2.Name
3. Pan Start POS 0.0
4. Pan End POS 0.0
5. Tilt Start POS 0.0
IRIS CLOSE to Exit
1. Select Sector Name. Press OPEN to enter Name Editing.
2. Edit name.
Sector Setup
1.Number 1
2. Name
→3. Pan Start POS 262.0
4. Pan End POS 0.0
5. Tilt Start POS 0.0
IRIS CLOSE to Exit
1. Select Pan Start POS. Press OPEN to enter.
2. Move the joystick Left or Right to move the dome. Press CLOSE
when done. Now the camera is on Pan Start Position.
Sector Setup
1.Number 1
2. Name
3. Pan Start POS 262.0
→4. Pan End POS 0.0
5. Tilt Start POS 0.0
IRIS CLOSE to Exit
Setup Pan End，Tilt Start，Tilt End according to the above instruction.
Sector Setup
1.Number 1
2. Name
3. Pan Start POS 262.0
Sector Setup
→6. Tilt End POS 0.0
7. Name Display On
IRIS CLOSE to Exit
4. Pan End POS 0.0
→5. Tilt Start POS 0.0
IRIS CLOSE to Exit
16