TM
AC INPUT
FROM INVE RTER
AC INPUT
FROM UTILITY
AC OUTPUT
TO LOAD
MODEL
FGA
ACINPUTS
ACOUTPUT
AUTOMATICTRANSFER SWITCH
808-0915
120-260V, 50/60Hz,15A MAX
120-260V, 50/60Hz,15A MAX
3033614
UL1008
DANGER
HAZARD OF FIRE, ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
This Xantrex PROwatt SW Auto Transfer Switch Owner's Guide is in addition to, and incorporates by reference, the relevant product manuals for
each product in the power system. After reviewing this guide you must read the relevant product manuals. Unless specified, information on safety,
specifications, installation, and operation is as shown in the primary documentation received with the product. Ensure you are familiar with that
information before proceeding.
Failure to follow these instructions will result in death or serious injury.
Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, SELLER (A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR
SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION; (B)
ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT,
INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY
SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK; AND (C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY
LANGUAGE OTHER THAN ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE TRANSLATION,
THE ACCURACY CANNOT BE GUARANTEED. APPROVED CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION
WHICH IS POSTED AT HTTP://WWW.XANTREX.COM.
Contact Information
Telephone: +1-800-670-0707 / +1-408-987-6030
Email: customerservice@xantrex.com,
http://www.xantrex.com/power-products-support/
Web: http://www.xantrex.com
Important Safety Information
Misusing or incorrectly connecting the external PROwatt SW Auto Transfer Switch
may create hazardous conditions for users or damage the equipment. Read the
following safety instructions and pay special attention to all Danger, Warning and
Caution statements in the guide. Danger, Warning, and Caution statements identify
conditions that may result in loss of life or personal injury. Notices identify conditions or
practices that may damage the unit or other equipment.
DANGER
ELECTRICAL SHOCK AND FIRE HAZARD
•Use a qualified installer or technician/electrician only. Consult your RV/motor home/vessel dealer for
guidance.
•Keep the auto transfer switch out of reach of children and pets.
•Do not expose the auto transfer switch to moisture, rain, spray, or snow. For marine application, use a
drip shield (PN: 808-1050).
•Do not operate the auto transfer switch if it has been damaged in any way.
•Do not disassemble the auto transfer switch There are no user-serviceable parts inside.
• More than one live circuit – disconnect all sources of supply before installing or servicing.
• This unit employs components that tend to produce arcs or sparks – To prevent fire or explosion, do not
install in compartments containing batteries or flammable materials.
• Do not connect grounding conductors to any neutral terminals; doing so defeats ground-fault protection
and may violate installation codes.
Failure to follow these instructions can result in death or serious injury.
WARNING
ELECTRICAL SHOCK AND FIRE HAZARD
•Use with PROwatt SW inverter only.
•For electrical connections, use stranded copper (Cu) wire only.
•Continuous load current not to exceed 100 percent of transfer switch current rating
•Tungsten filament load not to exceed 30% of switch current rating.
Failure to follow these instructions may result in death or serious injury.
NOTICE
EQUIPMENT DAMAGE
•Not intended for use with parallel engine generator (sets).
•This switch will not transfer if internal overcurrent device opens due to fault.
Failure to follow these instructions may result in equipment damage.
Introduction
Thank you for purchasing the PROwatt SW Auto Transfer Switch (PN:808-0915), an
automatic AC power transfer switch that automatically switches between primary and
secondary AC input sources to power a single AC output circuit.
The auto transfer switch automatically toggles between AC power from the PROwatt
SW inverter and AC power from another AC source such as utility (shore power) to
transfer to a single AC output such as a qualified load via a branch circuit.
975-0588-01-01 Rev B
November 2019
©2019 All trademarks are owned by Xantrex LLC and its affiliates.
PROwatt SW Auto Transfer Switch Owner’s Guide
PN:808-0915 http://www.xantrex.com
