Xblue Networks X-25 User manual

1. Plug the X-25 in and allow it to power up without connecting any Telephones.
Powering up
When the power LED stops ashing the X-25 will be fully powered up and
operational.
2. Use an Ethernet cable to connect your Personal Computer, Laptop or Desktop
running Windows XP, Vista or Windows7, to the LAN port of the X-25 System.
3. Open Internet Explorer and enter 192.168.10.1 in the address bar, and press enter.
When prompted enter the user name, which is “admin2583” and password which is
the word “admin” plus the last 6 alphanumeric characters (lower case only) of the
system’s “WAN MAC” address, which is found on the label on the back of the system.
5. Although the X-25 system comes up fully operational you may want to make some
6. Use the provided Ethernet cable to connect the X-25 WAN port to your network
router or network switch, depending on your network conguration choice.
authenticate. The rst one will be assigned extension 101. Each additional X-2020
telephone will automatically authenticate and be assigned the next available
extension number.
7. Connect your X-2020 telephones, one at a time, allowing each of them to
At Default:
• Extension 101 is the Attendant Extension (dial 0)
• All incoming telephone line calls will ring at all registered extensions
• The buttons labeled 1-4 on the phone are pre-programmed as telephone lines 1-4
4. Attention: To secure your system against unwanted outside intrusion (hacking)
8. Change the Extension Password - The X-25 system allows your X-2020
Telephones to automatically authenticate with your system. The password will be a
randomly generated 10 digit number. It is a good idea to change the password on all
24 extensions to a unique 6 to 10 digit alphanumeric password that has both upper
and lower case letters, even if you are not using all of them at this time.
Product Support is available at www.xblue.com or call 866-925-8312
Default Login and Passwords:
Level/Rights Login Default Password New Password
Administrator admin2583 adminxxxxxx
Administrator support Supportxxxxxx
User (Limited) User Userxxxxxx
xxxxxx = The last 6 alphanumeric characters (lower case) of the system’s WAN MAC Address
we strongly recommend that the rst thing you do is change all of the
System’s Passwords! Before you begin programming you should change all
three levels of passwords, admin2583, support and user. A password of up to 16
alphanumeric characters may be used and we recommend that you use at least 10.
The best passwords consist of upper and lower case characters and punctuation.
MAKE SURE TO MAKE A NOTE OF YOUR PASSWORD!
Download more information from www.xblue.com/x25-support.html
To change the password, log in as the Administrator go to:
Management --> Access Control --> Password
BE SURE TO MAKE A NOTE OF YOUR NEW PASSWORDS!
A list of additional security steps is available at www.xblue.com or by request at
[email protected]
Programming changes. You can do this manually or use the Wizard to walk you
through the most common programming parameters.
The X-25 can be installed several different ways but the best way
is to connect the Wide Area Network (WAN) port of the X-25
and all of your X-2020 telephones to your existing data network;
leaving the Local Area Network (LAN) port unused.
Installing the X-25 this way will allow the system to synchronize
the time and date from the Internet and if wanted connect low cost
Internet SIP Telephone lines.
Getting Started
Product Support is available at www.xblue.com or call 866-925-8312
Get the most current documentation from
LAN Port
WAN Port
Power
Line 4
Line 3
Line 2
Line 1
Telephone Lines
Cordless/FAX
System Components
X-25
8 Port Switch
Telephone
Line Cords
X-2020
24 Buon Sidecar
X-25 Components
Component Quanes may vary
Power Supply
Quick Start Guide
Ethernet Cable
Power Supply
Power Supply
Ethernet Cable
www.xblue.com/x25-support.html
© Copyright XBLUENetworks Revision 1

Product Support is available at www.xblue.com or call 866-925-8312
Best choice when connecting to an Existing network:
Connect the WAN port of your X-25 to your existing network,
leaving the LAN port disconnected after using it for the initial
installation programming.
ISP
Existing Router
Network Switch
Internet
Network Conguration Choices
Best choice with an Existing Network and Remote Phones:
Obtain a static IP address from your Internet Service Provider
(ISP). Connect the WAN port of your X-25 to a dedicated network
switch (purchased separately) and enter the Static IP address in
the WAN programming of the X-25, without connecting the LAN.
ISP
Existing
Router
Network Switch
Internet
Network Switch
Product Support is available at www.xblue.com or call 866-925-8312
Internet
ISP
Network Switch
Using the X-25 as a Router and Connecting Remote Phones:
Obtain a static IP address from your Internet Service Provider
(ISP). Connect the WAN port of your X-25 to the ISP Modem and
use the LAN port to connect all of your phones and computers.
Connecting Telephone Lines:
You can connect up to four (4) analog (standard or PSTN)
telephone lines to your X-25. Connect one line to each port, in
the order that you want them to ring 1 - 4 or take advantage of
XBLUE Networks’
Low Cost premium
Cloud telephone lines
which are provisioned
right over your
Internet Broadband
Connection.
Use the provided line
cords to connect the
telephone lines to the
X-25.
Line 1
Line 2
Line 3
Line 4
Telephone
Company
In this conguration some
modems require “Bridge” or
“Concurrent Bridge Mode”,
if this is necessary (WAN
registration fails) contact your
ISP. The X-25 will authenticate
directly to the ISP.
The X-2020 telephone is also
a “Layer 2” network switch. This
allows you to plug your existing
data cable into the telephone and
then connect from your telephone
to your computer. Allowing
you to use your current network
conguration.