Xebex Fitness ABMG-3 Quick start guide

ASSEMBLY INSTRUCTIONS / OWNERS MANUAL
I MPORTANT :READ ALL ASSEMBLY INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE USING THIS PRODUCT. REFERENCE ALL
SAFETY GUIDELINES AND WARNING LABELS. RETAIN PRODUCT LITERATURE FOR FUTURE REFERENCE.
A
S FETY :OPERLY WARM UP AND STRETCH BEFORE EXERCISING. IF YOU FEEL PAIN OR DIZZINESS AT ANY TIME WHILE
EXERCISING , STOP IMMEDIATELY AND CONSULT YOUR PHYSICIAN.
PR
AIR BIKE ABMG-3

PAGE 1 ASSEMBLY INTRO
A
ASSEMBLY
SSEMBLY P
PREPARATION
REPARATION
To ensure ease of product assembly, please take time to verify the size and quantities of all required
assembly hardware. Use the itemized parts listing and hardware chart for reference.
The product assembly process has been documented in easy to follow stages. Please read all assembly
instructions carefully. Take time to review the manual and familiarize yourself with the entire
assembly process before proceeding.
Assembly Tip: It is always helpful to pre-stage the items needed for each assembly step.
Perform product assembly in a 4ft. x 6ft. flat area. Note: After assembly is completed, allow a minimal
of 2-3ft. of space on each side of bike for user access and dismounting.
Do not dispose of any packaging materials until assembly of the product is completed.
Assembly tools are included, but you may also use standard household tools to complete assembly of
this product.
If you experience problems with operation of the equipment after assembly, please reference the
troubleshooting guide in this manual.
For added component life, follow the preventative maintenance tips listed in this manual.
Make sure to completely fill-out the product registration form & return it to us within 30-days of
purchase.
I
IMPORTANT
MPORTANT P
PRECAUTIONS
RECAUTIONS
WARNING: To reduce the risk of injury, please read the following precautions before assembling or using your new product.
1. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of stated precautions.
2. Read all instructions and enclosed literature carefully. Understand the assembly and operation before using the equipment.
3. Use equipment on a flat level surface. Use adjustment levelers on the bottom of equipment to help stabilize unit.
4. It’s recommended to place an exercise mat beneath the equipment for added protection of floors or carpets.
5. Keep children & pets away from equipment at all times.
6. Inspect product on a frequent basis. Tighten loose assemblies or hardware as needed. Replace worn or damaged parts.
8. Recommended user weight should not exceed 300 lbs.
9. Keep equipment clean and properly maintained.
10. Observe and adhere to all warning labels posted on equipment.
11. Properly warm-up and stretch before starting any strength training or cardio exercise routine.
12. If you feel pain or dizziness at any time while exercising, stop immediately and consult your physician.
Safety Warning: Before starting an exercise program, consult your physician. This is especially important for individuals over the age
of 35 or persons with pre-existing health problems. It’s important to read all instructions carefully. We assume no responsibility
for personal injury or consequential damages sustained by or through the use of this equipment. Additional terms & con-
ditions are listed in the back of this manual or enclosed owners manual.
Colors and specifications are subject to change without notice.
7. This equipment is intended for indoor use only. Use in non-recommended environment
s
can lead to serious injury and will void all related warranties & liabilities.

ASSEMBLY PARTS LISTING PAGE 2
ITEM# Q'TY
1 1
2 1
3 1
4 1
5 1
6 1
7 1
8 1
9 1
10 1
15 2
16 1
17 1
18 2
20 1
21 1
22 6
23 12
24 17
25 2
30 2
31 2
32 5
1
PIVOT BOLT M8*35 LENGTH
SPACER WASHER 12*8.2*3.5T
NYLON NUT M8
RIGHT PEDAL
SPRING WASHER 12*8.5*1.5T
WASHER 18*8.5*1.5T
BOLTS M5*10 LENGTH
CONNECTING ARM (PREINSTALLED)
LEFT PIVOT ARM ASSEMBLY
RIGHT PIVOT ARM ASSEMBLY
FOOT REST
LEFT PEDAL
CONSOLE
CONSOLE MAST
ADJUSTABLE SEAT SLIDER
SEAT POST
SEAT
SEAT SLIDER ADJUSTABLE KNOB
ASSEMBLY PARTS LISTING
DESCRIPTION
BASE FRAME ASSEMBLY
FRONT STABILIZER ASSEMBLY
REAR FRONT STABILIZER ASSEMBLY
SENSOR CABLE
BUTTON HEAD ALLEN BOLT M8*20 LENGTH
76 1GEAR SHIFTER CABLE
75 3P CABLE

PAGE 3 EXPLODED VIEW
NOTE
NOTE: THE EXPLODED PARTS VIEW IS SHOWN FOR REFERENCE ONLY. SOME ITEMS MAY BE PREASSEMBLED.
: THE EXPLODED PARTS VIEW IS SHOWN FOR REFERENCE ONLY. SOME ITEMS MAY BE PREASSEMBLED.
PLEASE REFER TO THE INDIVIDUAL ASSEMBLY STAGE INSTRUCTIONS FOR DETAILED PARTS ORIENTATION.
PLEASE REFER TO THE INDIVIDUAL ASSEMBLY STAGE INSTRUCTIONS FOR DETAILED PARTS ORIENTATION.
Assembly Parts

ASSEMBLY STAGE #1
Attach Stabilizers to the Main Base
Assembly Hardware Required:
#22 Button Head Allen Bolt Qty. 4 #24 Washer Qty. 4
#23 Spring Washer Qty. 4
Assembly Description:
A) Assemble the Front Stabilizer Assembly (#2) to the Main Base Assembly (#1) using 2-Button Head Allen Bolt
B) Assemble the Rear StabilizerAssembly (#3) to the Main Base Assembly (#1) using 2-Button Head Allen Bolt
C) Use the AdjustableLevelers on the bottom of the Stabilizer Assemblies to adjust the bike and keep it from rocking
on an uneven surface (Figure 1).
Assembly Step #1 completed.
ASSEMBLY INSTRUCTION PAGE 4
(#22), 2-Spring Washers (#23), and 2-Washers (#24). Note: Make sure that the transport wheels on the Front
Stabilizer are facing away from the Main Base Assembly as shown.
(#22), 2-Spring Washers (#23), and 2-Washers (#24).

ASSEMBLY STAGE #2
Attach Console Mast & Mount Computer on the Main Base
Assembly Hardware Required:
#22 Button Head Allen Bolt Qty. 2 #23 Spring Washer Qty. 2
#24 Washer Qty. 2
Assembly Description:
Assembly Stage #2 completed.
ASSEMBLY INSTRUCTIONPAGE 5
A) Slide the Computer Mast (#6) onto the corresponding mounting area of the Base Frame Assembly.
Secure the mast to the base frame using 2-Button Head Allen Bolts (#22), 2-Spring Washers (#23) ,and
2-Washers (#24).
B) Install (4) AA Batteries into the base of the Computer (#5). Connect the Sensor Cable (#4) to the
receptacle end of the shorter cable coming from the back of the computer. Link the 3P Cable (#75) to the
Gear Shifter Cable (#76). Tuck the excess cable lengths into the mast and slide the computer onto the
mast mounting plate. Secure the Computer in place using 2-Bolts (#25).

ASSEMBLY STAGE #3
Attach Seat Slider and Seat to Main Base Assembly
Assembly Description:
A) Insert the Adjustable Seat Slider (#7) into the u-channel of the Seat Support Post (#8). Secure the seat slider
assembly in place using the 1-Seat Adjustment Knob (#10).
Seat Adjustments: Adjust the seat height by unscrewing and pulling out on the Seat Post Adjustment Knob (#12).Select a
desired seat post heightand retighten the knob until seat post is secure. Proper Height Adjustment: Adjust seat height so the user
is comfortable during use (pedaling motion). As a reference point, the users leg should be slightly bent at the bottom of thepedal
stroke. The horizontal seat position can be adjusted using theSeat Slider (#7) . Note: If the seat post wobbles during use, make sure
the u-clamp and all adjustment knobs are securely tightened.
Assembly Stage #3 completed.
ASSEMBLY INSTRUCTION PAGE 6
B) Place Seat(#9) onto the plate of the seat slider (3 bolts are already f i xed on the seat), and assemble it using
3-Flat Washer(#24) and 3-Nylon Nut(#32). Set the seat at the desired position and secure it in place by
tighetening the u-clamp on the underside.Tighten the clamp until the seat no longer twists or tilts.
Assembly Hardware Required: (*Assembly hardware may be pre-installed)
#24 Flat Washer * Qty. 3 #32 Nylon Nut M8 * Qty. 3

ASSEMBLY STAGE #4
Attach Pivot Arms to the Main Base
#24 Flat Washer Qty. 2 #30 Pivot Bolt M8 Qty. 2
#32 Nylon Nut M8 Qty. 2
Assembly Description:
A) Install the Pivot Arms (#16 & #17) by threading the (preinstalled) pivot shaft into the corresponding pivot-boss of
the Base Frame Assembly (#1). Using a standard crescent wrench (not included), thread each shaft into the pivot
-boss using a clockwise rotation. Fully tighten each shaft until it is flush against the pivot-boss of the Base Frame
Assembly. (Reference Figure #3)
B) Once the Pivot Arms are mounted to the Base Frame Assembly, attach the ends of theConnecting Arms (#15)
using 1-Pivot Bolt (#30), 1-Flat Washer (#24), and 1-Nylon Nut (#32) per side. (Figure #4).
Assembly Stage #4 completed.
ASSEMBLY INSTRUCTIONPAGE 7
Assembly Hardware Required:

ASSEMBLY INSTRUCTION
ASSEMBLY STAGE #5
Attach Pedals & Foot Rest to the Main Base Assembly
Assembly Description:
Assembly Note: The right and left pedals are appropriately marked (R) and (L). The threading orientation on the left pedal is
reversed from the threading orientation on the right pedal. To avoid stripping of the threads on the pedals or crank arms, make sure
to follow the proper assembly orientation.
A) Assemble the Right Pedal (#20) to the Right Crank Arm on the Main Base Assembly. Thread the pedal on the crank arm
(clockwise) and securely tighten with the pedal wrench (included). (Reference Figure #5)
B) Assemble the Left Pedal (#21) to the Left Crank Arm on the Main Base Assembly. Thread the pedal onto the crank arm
(counterclockwise) and securely tighten with the pedal wrench (included).
Assembly Tip: Take time to review the additional information regarding computer operation, product maintenance, and warranty.
Congratulations !
You have successfully completed the assembly of this product and you are ready to start exercising toward a healthier lifestyle!
PAGE 8

PAGE 9 TROUBLESHOOTING
BASIC TROUBLESHOOTING TIPS
BASIC TROUBLESHOOTING TIPS
PROBLEM DESCRIPTION SUGGESTED SOLUTION
NO DISPLAY 1) CHECK BATTERY ORIENTATION: + / -
2) CHECK BATTERY VOLTAGE: (2) AA BATTERIES 1.5 VOLTS EACH
3) CHECK CABLE CONNECTIONS: MAKE SURE CONNECTIONS ARE
SECURE AND IN THE CORRECT ORIENTATION.
4) CHECK CABLE ASSEMBLIES FOR DAMAGE: PINCH POINTS &
POSSIBLE SHORTING OF WIRES.
5) CHECK FOR POSSIBLE COMPUTER DAMAGE: CRACKED DISPLAY
WINDOW (BLACK SCREEN).
*If computer still fails to operate after checking these suggestions,
contact us for technical support.
PRODUCT WILL NOT SIT LEVEL 1) USE LEVELERS ON THE BOTTOM OF THE STABILIZERS TO ADJUST
EQUIPMENT TO UNEVEN SURFACES.
SEAT POST MOVEMENT 1) MAKE SURE THE ADJUSTMENT KNOB IS LOCKED INTO A SEAT
POST HOLE.
2) SECURELY TIGHTEN THE SEAT POST IN PLACE BY TURNING THE
ADJUSTMENT KNOB.
PEDAL WOBBLE 1) CHECK TO MAKE SURE PEDALS ARE INSTALLED CORRECTLY
(ORIENTATION) AND MOUNTED FLUSH WITH THE CRANK ARMS.
2) LOOSEN THE PEDALS, CHECK FOR POSSIBLE CROSS-THREADING
OF CRANK ARMS.
NO SPEED READING 1) CHECK COMPUTER CONNECTION: MAKE SURE CONNECTORS ARE
SECURE AND IN THE CORRECT ORIENTATION.
2) CHECK SPEED SENSOR. CONFIRM CABLE CONNECTION AND
ALIGNMENT WITH MAGNET.
Make sure to reference the assembly steps & parts information in this manual when performing any troubleshooting.
If you experience other technical problems that are not listed or have additional questions, please
check www.xebexfitness.com

PREVENTATIVE MAINTENANCE PAGE 10
E
EQUIPMENT
QUIPMENT M
MAINTENANCE
AINTENANCE
Use a dampened soft-cloth to wipe equipment free of perspiration after each use. Avoid getting
excessive moisture on computer or electronic components. Do not use abrasive cleaners or
petroleum-based solvents to clean equipment.
Do not remove drive train shrouds or attempt any technical service on equipment without consulting
an authorized service representative.
Regularly inspect product for lose assembly hardware and worn components.
(If applicable) For added safety, unplug equipment from the wall socket when it is not being used.
Use a product /exercise mat underneath equipment for protection of floors & carpets.
(If applicable) Apply recommended component lubricants at the required time periods.
Keep product assembly manual, purchase receipt, and service records in a safe storage place.
( If applicable) Periodically check batteries for proper voltage output & replace as needed.
Do not store or use equipment outdoors.
Moving equipment:
Lift up the rear stabilizer and carefully tip the bike forward until the front stabilizer wheels touch
the floor. Do not use the computer or pivot arms to move the unit. You may wish to lock the fan in
place (which will keep the arms from moving), by turning the safety knob (referenced on page 7)
until it makes contact with the fan wheel.
TRAINING FOR SUCCESS
TRAINING FOR SUCCESS
How you start an exercise program depends on your physical condition. If you have been inactive
for awhile or you have pre-existing health condition, you should start slowly. Initially you may only
be able to exercise for a short amount of time using minimal resistance levels or weight loads.
Begin your desired training program slowly and gradually increase the amount of time you
exercise. Apply realistic goals, that have been set by you or your physician. You should see
sufficient gains in your personal fitness level within 6-8 weeks of continuous exercise, but do not be
discouraged if it takes longer. It is very important to exercise at your own pace and become
confident in obtaining your goals. It is also important to apply warm-up, stretching, and cool down
periods with any exercise program.
As your fitness level increases, so will your confidence and sense of accomplishment. Regular
exercise and a healthy diet will energize you and offer a sense of well-being.

Use 3-in-1 OIL only. Do not use anything else!
1. Pedal Check: (Monthly):
Tighten the pedals with a 15mm wrench. The right side pedals will tighten “righty tighty” (clockwise)
and the left side pedal will tighten “lefty tighty” (counter-clockwise).
2. Handlebar Assembly Check (Monthly)
Insert Screw Driver through peg of bike and tighten
3. Handlebar Assembly Check (Monthly):
Tighten the handlebar using a 22mm wrench. Tighten these down as tight as possible for both sides.
Next, tighten handlebar assembly peg nut with 22mm socket wrench. Note: There will be a little play
in these arms after tightening but this is normal.
XEBEX AIR BIKE
Maintenance Information
Service
Daily
Monthly
Quarterly
Annually
Clean/Dry Frame & Console w/ mild soap and cloth
X
Inspect Unit for Noise or loose components
X
Ensure Unit is level-Adjust Stabilizer Feet
X
Tighten Crank & Bell Crank Bolts, Tighten Pedals
X
Tighten Seat Bolts
X
Tighten Handlebars
X
Check and Tighten Linkage Arm Pivot points
X
Change Console Batteries
X
Lubricate Chain
X
Inspect & Adjust Chain Tension if Needed
X
Tighten Main Frame Bolts and Stabilizers
X
-See detailed instructions below

XEBEX AIR BIKE
Maintenance Information
4. Linkage Arm Check (Monthly): Tighten the linkage bolts and nuts using a 6mm Allen wrench and
13mm wrench. Tighten these parts snug, but do not over tighten or keep tightening. Note: There will be
little play in these linkages after tightening, but this is normal. Some units will have a 22mm nut instead of
a 13mm nut.
5. Chain Adjusting Check (Quarterly): Check the two drive chains to make sure they are equally tight.
Each chain should have just a slight flex to it, but it should also not be tightened too much. First check
the main rear chain and adjust the tension if needed. Proper chain tension is about 3mm of
movement up and down or a slight up and down movement.
To adjust the chain, use the 15mm wrench to loosen the crank axle nut by rotating the wrench
counter-clockwise. Once the axle nut is loosened use the 10mm wrench to turn the chain tensioner
nut clockwise or counter-clockwise to adjust the tension. Repeat the process to the front tensioner
and check the tension on each chain again. Adjust each section to get the proper alignment. Once
you get the proper chain tension, tighten the 15mm axle nuts. Make sure the tension remains the
same while tightening the axle nuts. If the tension is too much, loosen the 10mm nut slightly to
release slack until it is equal.
6. Clean and Lubricate the Chain (Quarterly): The chain must be cleaned and lubricated at least
every 50 hours. If the Air Bike is used in an institutional setting, then the chain must be cleaned and
lubricated at least once a week. Use 3-in-1 Oil only, do not use anything else!

Part List
PART DESCRIPTION PART# QTY PART DESCRIPTION PART# QTY
FRAME 1 1PC
1PC
FRONT STABILIZER 2 1PC
45 1PC
REAR STABILIZER 3 1PC
46 1PC
SENSOR CABLE 4
47 4PAIR
COMPUTER 5
48 1PC
COMPUTER POST 6
49 1PC
SEAT TRACK 7
50 1PC
SEAT POST 8
LEFT CHAINGUARD
51 1PC
SEAT 9
52 1PC
FIX HANDLEBAR 10
53 1PC
KNOB 12
54 1PC
CONNECTING ARM PAIR 15 1PAIR
55 1PC
LEFT LEVER ARM 16 1PC
RIGHT LEVER ARM 17 1PC
FOOT REST 18 2PC
LEFT PEDAL 20
1PC
RIGHT PEDAL 21 1PC
BUTTON HEAD ALLEN BOLT M8*20L 22 6PC
SPRING WASHER 23 12PC
WASHER 18*8.5*1.5T 24 17PC
BOLT M5*10L 25 2PC
2PC
5PC
1PC
1PC
1PC
1PC
1PC
1SET
ALLEN BOLT M8 30
NYLON NUT 32
GEAR SHIFTER
CRANK ARM RIGHT
38
CRANK ARM LEFT 39
BRACKET 40
LEFT CRANK ECCENTRIC 41
RIGHT CRANK ECCENTRIC W/46T SPROCKET 42
BOTTOM BRACKET SET 43
HEX BOLT M5*10L 6PC
CRANK BOLT 59
2PC
SENSOR STOPPER 60 1PC
SCREW M4*16L 61 1PC
WASHER 10*20*3T 62 2PC
WASHER 10*19*1.5T 63 2PC
DOME NUT 3/8” 64 2PC
WASHER 5*12*1T 65 1PC
SCREW M5*12L 66 4PC
SCREW M5*10L
67
2PC
ALLEN BOLT M5*25L
68 3PC
SPEED NUT SET
69
6SET
WASHER 5*10*1T 71 3PC
WASHER 22*16*2T
72 2PC
WASHER 8.5*28*5
73
1PC
WASHER #16 74
4PC
GEAR SHIFTER CABLE
75 1PC
CHAIN
44
CHAIN
SPEED SENSOR BRACKET ZEPHYR
CHAIN TENSIONER
1PC
76 1PC
77
1PC
MAGNETIC RESISTANCE MECHANISM
IDLER HUB
1PC
WHEEL
1PC
RIGHT CHAINGUARD
1PC
1PC
SPOKE PROTECTOR LEFT
1PC
WHEEL CAGE RIGHT
1PC
WHEEL CAGE LEFT
1PC
46T SPROCKET
57
SPOKE PROTECTOR RIGHT
78
1PC
79
1PC
3P CABLE