XENO XPSU1208e User manual

1
Ref: XPSU1208e / XPSU1216e
12V dc 4A/8A Low
Profile CCTV SMPSU
XPSU1208e XPSU1216e
4A: 8 x 0.5A Fused Outputs 8A: 16 x 0.5A Fused Outputs
Thank you for choosing this high quality 12V dc power supply. Before attempting to
connect or operate this product please make sure you carefully read these
instructions for your safety.
General:
A range of 12V dc power supplies capable of delivering fully rated current to load, housed within
a low profile metal enclosure, suitable for internal use only. Provided with 8 or 16 individually
PTC fused outputs ideal for low powered CCTV installations.
INSTALLATION AND SET-UP
This unit is only suitable for installation as permanently connected equipment and MUST be fed from a
mains power source having a separate (approved) disconnect device - fitted with a fuse or other over-
current protection device rated at 3A maximum. Ensure that the disconnect device used has appropriate
earth fault protection to the applicable standard.
The enclosure is NOT SUITABLE for external use; bushings should meet a minimum flammability specification
of UL94 HB.
The PSU should be installed according to all relevant safety regulations.
1) Fix to wall or other support structure using the screws/fixings supplied or use appropriate types for the
surface it is being mounted to.
2) Mains input cable must be to the applicable standard with a 3A or greater current capacity, having a
minimum operating voltage of 300/500V ac.
3) The low voltage output cable must be correctly sized to carry the rated load current to the devices
connected to the PSU.
4) Mains input and low voltage output cables should be routed to use different entry/exit holes in the
enclosure.
5) To comply with current BS EN60950 safety legislation the supplied cable ties must be used to secure
mains input and low voltage output wiring.
Norbain SD Tel: [phone]
210 Wharfdale Rd, Fax: [phone]
Winnersh Triangle, Web: www.vista-cctv.com
Wokingham, Berkshire,
RG41 5TP, UK.

2
Ref: XPSU1208e / XPSU1216e
OPERATION
This unit is intended for use by Service Personnel only - There are NO USER SERVICEABLE parts inside.
The green Mains LED will be illuminated whilst the mains supply is present. In the event of a fault
condition, the red Fault LED will also be illuminated on the module.
MAINTENANCE
There is no regular maintenance required of this PSU.
If the output of the PSU fails the cause of the failure should be investigated e.g. short circuit load. The
fault should be rectified before restoring power to the PSU. The fuse(s) may need to be replaced.
Ensure the correct fuse rating and type is used.
DISPOSAL OF PRODUCT AT END OF LIFE
This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic
Equipment (WEEE). At the end of life, the product must be separated from the domestic waste stream
and disposed via an appropriate approved WEEE disposal route in accordance with all national and local
regulations.
For more information see: www.recyclethis.info

3
Ref: XPSU1208e / XPSU1216e
SPECIFICATION
Input Specification
VPSU1208e
VPSU1216e
Voltage (rated)
100-240V ac 100-240V ac
Voltage (operating)
90-264V ac 90-264V ac
Frequency
50-60Hz 50-60Hz
Mains Input Fuse (Terminal)
T2.0A HRC
T3.15A HRC
Module fuse - Mains
T2.0A HRC
T2.0A HRC (x2)
Max standby Power
0.5W (no load connected)
1.0W (no load connected)
Max Mains Input Current
1.5A
3.0A
Output Specification (per power module)
Voltage
11.4 –12.6V dc (12V dc nominal)
Note: Please factor this load ‘Voltage variance’ in when designing systems
Max load current (per module)
4A
Ripple
150 mV pk-pk max
Module Output Fuse
F4.0A
Load output Fuse
See Model Specification Table below
Overload
Electronic shutdown until overload or short circuit removed
Local Indicators
MAINS LED (Green)
Mains present
FAULT LED (Red)
Fault present: Output fuse fail
(requires load to be connected)
Fused Outputs
Model:
XPSU1208e
XPSU1216e
No. of Fused outputs:
8
16
PTC (auto resetting) Fuse Value:
[as fitted in fused output module(s)]
8 x 500mA
16 x 500mA
Mechanical
XPSU1208e
XPSU1216e
Enclosure Dimensions
h x w x d (mm) [external]
188 x 205 x 60
310 x 245 x 60
Weight
1.5Kg
2.7Kg
Environmental
Temperature
-10 to +40°C (operating) 95% RH non-condensing
-20 to +80°C (storage)

4
Ref: XPSU1208e / XPSU1216e
COMPLIANCE
This product meets the essential requirements of the following EU Directives:
Low Voltage: 2014/35/EU
EMC: 2014/30/EU
RoHS2: 2011/65/EU
WEEE: 2012/19/EU
The packaging supplied with this product may be recycled.
Please dispose of packaging accordingly.