Xerox Integrated Fiery Color Server User manual

Quick Start Guide
Addendum for Xerox
Integrated Fiery Color Server
For the
Xerox Color 550 Production Printer
August 2010
45084799

CONFIGURATION TRAINING GUIDE 8/09 1-1
Module 1
Introduction
Introduction
Module overview
This Introduction Module will provide you with an overview of this
training program. Information on the Fiery will be referenced to the
Installation and Service Guide
Module objectives
By the end of this module you will be able to do the following:
Identify required training modules
Locate information on the Integrated Fiery Color Server in
the Installation and Service Guide
Describe Integrated Fiery Color Server features
Identify Integrated Fiery Color Server hardware
specifications
Identify Integrated Fiery Color Server network connectivity
Describe how the Integrated Fiery Color Server operates

INTRODUCTION Integrated Fiery Color Server
1-2 8/09 CONFIGURATION TRAINING GUIDE
Training overview
This course is designed for both the Xerox Analyst and the Service
Representative.
For Xerox Analysts, Module 2: Configuration of the Integrated Fiery
Color Server is required and Module 3: Servicing the Integrated
Fiery Network Controller is optional.
If you are a Xerox Service Representative, Module 2: Configuration
of the Integrated Fiery Color Server is optional and Module 3:
Servicing the Integrated Fiery Color Server is required.
Course Prerequisites
The Xerox Service Representative training prerequisites for this
course include the following:
Color Basic (C10500)
Network Continuum Basic (C7166)
Introduction to Digital (C9250)
Laser Safety Training Program (772P20441)
PWS/PSS Skills Knowledge
Ishihara Color Test (C1124)
These training prerequisites are available via Xerox eLearning and
can be located by searching the short code for each prerequisite
(i.e., the short code for Color Basic is C10500).
In addition, The Xerox Service Representative is required to have
the following hardware and software:
A Personal Work Station (PWS) configured with Xerox
Golden Image
Internet Explorer v. 6.0
Minimum 500 MB free space on your C: drive
Laptop with a Network Interface Card (NIC) installed
If you do not meet all of these prerequisites, call your instructor over
to discuss a recovery plan. This may include evening or post-
school work to complete all of the requirements. In rare cases it
might mean that you should not take the present course until some
later date.

Integrated Fiery Color Server INTRODUCTION
CONFIGURATION TRAINING GUIDE 8/09 1-3
Introduction to the Integrated Fiery Color Server
The Fiery is a high-performance color controller that adds computer
connectivity and highly efficient color printing capability to digital
color copiers. It is optimized for high-speed communications,
processing, rasterization, and printing of continuous tone color and
monochrome (black and white) pages. Users can print from
networked Mac OS computers and from networked PCs running
Windows. In addition, the Fiery USB-Type A ports allow printing
directly from a USB device.
Features
As an integral part of the printing system, the Integrated Fiery Color
Server enables users to:
Send images over AppleTalk, TCP/IP, and Novell
networks, or through a USB device to print on a copier.
Spool print jobs and select a printing priority for each job.
Users can control spooled print jobs sent to the Fiery with
user software running on networked Mac OS computers
and PCs.
Print files in color, grayscale, and black and white.
Use the copier as a high-resolution color scanner with
Remote Scan utility.
Use 136 resident fonts (117 Adobe Type 1 PostScript fonts
with Euro Currency support, and 19 TrueType fonts), plus
two Adobe Multiple Master fonts used for font substitution
when printing PDF files. WebTools or the Command
WorkStation can be used to download additional fonts.
Use built-in ColorWise™ color management and
NetWise™ networking features.
Specifications
The Integrated Fiery Color Server Hardware specifications include:
Celeron M440 Solo Intel 1.86GHz CPU
512 MB Memory (minimum)
80GB SATA hard disk drive (minimum)
Three USB-Type A ports for printing through a USB device
Supports AppleTalk and TCP/IP protocols simultaneously
Ethernet port for twisted pair
(10BaseT/100BaseTX/1000BaseT) network connection

INTRODUCTION Integrated Fiery Color Server
1-4 8/09 CONFIGURATION TRAINING GUIDE
Network Connectivity
When the Fiery is connected to a network, it behaves as a
networked printer. The Fiery supports the following network
protocols (rules that enable computers on a network to
communicate with each other):
AppleTalk, Bonjour
TCP/IP, which also includes the BOOTP, DHCP, FTP, HTTP,
IMAP, IPP, IPv4, IPv6, LDAP, LPD, NBT, POP3, Port 9100,
SMB, SMTP, SNMP, SNTP, SSL/TLS, 802.1x and IPSec
protocols
These protocols can run concurrently on the same cable.
Computers that use other protocols can print through a server that
uses one of the supported protocols. The Fiery is autosensing, and
handles all connections simultaneously. This information needs to
be managed by a local administrator.
How the Fiery Network Controller Operates
To gain an understanding of how the Fiery Color Server Operates,
consult the Integrated Fiery Color Server for the WC 7700 Series
MFP Installation and Service Guide, Introduction.
Service Documentation
This training document is intended to provide general procedures.
For specific detailed procedure, refer to your service
documentation.

Integrated Fiery Color Server INTRODUCTION
CONFIGURATION TRAINING GUIDE 8/09 1-5
Module Summary
This module provided you with an overview of this training program
and the Integrated Fiery Color Server.
Review the objectives at the beginning of the module. If you do not
feel comfortable with you ability to perform any objective, review the
materials for that objective.

INTRODUCTION Integrated Fiery Color Server
1-6 8/09 CONFIGURATION TRAINING GUIDE
Notes

CONFIGURATION TRAINING GUIDE 8/09 2-1
Module 2
Configuration of the Integrated
Fiery Color Server
Introduction
Module overview
This Module (Configuration of the Integrated Fiery Color Server)
provides you with information on how to setup the Integrated Fiery
Color Server Procedural information on configuring the Integrated
Fiery Color Server will be referenced to the Integrated Fiery Color
Server Configuration Guide
Module objectives
By the end of this module you will be able to do the following:
Use the Fiery Installation Instructions for Xerox Color 550
Production Printer as a resource.
Use the Integrated Fiery Color Server Configuration Guide
as a resource.
Prepare the Integrated Fiery Color Server for Setup.
Setup the Integrated Fiery Color Server from the Copier
Touch Panel.
Setup the Integrated Fiery Color Server from a network
computer.

CONFIGURATION Integrated Fiery Color Server
2-2 8/09 CONFIGURATION TRAINING GUIDE
Preparing for Fiery Setup
Basic Installation of Fiery to the Xerox Color 550
Production Printer
Consult the Fiery Installation Instructions for the Xerox Color 550
Production Printer, section: Basic Installation for information on
setting up the Fiery to connect to the WorkCentre 7700 Series
MFP.
Network Switch Connection the Fiery to the Xerox Color
550 Production Printer (Optional)
Consult the Fiery Installation Instructions for the Xerox Color 550
Production Printer, section: Network Switch Connection (Optional)
for information on setting up the Fiery to connect to the Xerox Color
550 Production Printer using a Network Switch (purchased
separately).
Preparing for Fiery Network Setup
Fiery on the Network
Consult the Fiery Network Controller for Xerox Color 550
Production Printer Configuration and Setup Guide, section:
Connecting to the Integrated Fiery Color Server on the Network for
information on connecting the Fiery to a network.
Preparing for Fiery Setup
Consult the Integrated Fiery Color Server for Xerox Color 550
Production Printer Configuration and Setup Guide, section:
Preparing for Fiery Controller Setup for information on configuring
the Fiery. Topics covered in this section include: Levels of access
and control, Fiery Print Connections, and WebTools.
Setup
Setup configures the Fiery to communicate with other devices and
to manage print jobs. Perform Setup the first time you turn on the
Fiery after new system software is loaded, or any time Server
software is reinstalled. When the network or user printing
environment changes, change the Fiery options accordingly.

Integrated Fiery Color Server CONFIGURATION
CONFIGURATION TRAINING GUIDE 8/09 2-3
NOTE: You cannot access Setup functions from Command WorkStation,
Macintosh Edition.
Setup from the copier touch panel
To setup the Fiery from the Copier touch panel, consult the
Integrated Fiery Color Server for Xerox Color 550 Production
Printer Configuration and Setup Guide, section: Setting up the
copier, EFI Xerox Color 550 Config.
Setup from a network computer
To set up the Fiery from a network computer, consult the Integrated
Fiery Color Server for Xerox Color 550 Production Printer
Configuration and Setup Guide, section: Setting up the Fiery
Controller from a network computer.
Setting up the Fiery from a network computer
After you perform initial Setup from the copier touch panel, you can
change most Setup options from a network computer by using
Configure. To use Configure from a network computer, you must
know the Fiery Administrator password.