Xiamen VB Series User manual

User Manual
Applicable models:
VB20, Vigor, Vigor U, Vigor X
VB SERIES, Gio, Bro, Eggo

INDEX
Description of hearing aid............- 1 -
ON/OFF function ..........................- 4 -
Inserting/Replacing the battery...- 6 -
Attach dome (OF) .........................- 8 -
Attach tubing (OF) ........................- 9 -
Inserting/Removing hearing aids- 13 -
Operation of hearing aid............- 15 -
Switch control .............................- 15 -

Pairing hearing aids with Android/iOS
device .......................................... - 19 -
FCC Statement ..............................- 21 -

- 1 -
Description of hearing aid

- 2 -

- 3 -
1. Front microphone input
2. Switch control
3. Rear microphone input (optional)
4. Battery door
5. Sound tube
6. Dome
7. Retention

- 4 -
ON/OFF function
1. When the battery door is closed, the
hearing aids on, and the default program will
be activated.
2. To turn off the hearing aids, partly open the
battery door.
Tip: Whenever the hearing aids are not in use,
remember to turn them off to avoid
unnecessary battery consumption.

- 5 -

- 6 -
Inserting/Replacing the battery
1. Open the battery door completely by using
your fingernail.
2. Remove the used battery if present. Insert
the new battery with the positive side in the
correct position. The battery door has a ‘+’
indicator to help determine the correct
insertion.
3. Gently close the battery door.

- 7 -
Tip: When the hearing aids are not in use for
an extended period of time, removing the
batteries may help prevent corrosion of the
battery compartment, and ensure that
battery life is not shortened.

- 8 -
Attach dome (OF)
Push the dome over the flanges on the thin
tube. Make sure that the new dome is
properly and securely mounted.
Gently press and twist the tube into
connector base until the tube is fixed firmly.

- 9 -
Attach tubing (OF)
Push the tube into connector
base of device, insert into the
recessed jack and rotate
clockwise about 3.5 turns until the
tube is fixed firmly .

- 10 -
Attach\remove tubing and dome (RITE)

- 11 -
1. Make sure the receiver tube plug is entirely
sheathed in the black receiver and insert into
1. receiver flange
2. receiver jack
3. receiver tube plug
4. receiver tube
5. connector base

- 12 -
a recessed jack.
2. Push the dome over the flanges on the
black receiver. Make sure that the new dome
is properly and securely mounted.
3. Gently press the receiver tube into
connector base of device, insert into a
recessed jack follow the red arrow until the
tube is fixed firmly.
4. Pull tubing off straightly.

- 13 -
Inserting/Removing hearing aids
Insertion
1. Hold the thin tube where it bends, and
gently push the dome into the ear canal. Push
the dome far enough into the ear canal so
that the thin tube lies flush with the head.
2. It is important that the tube and the dome
fit correctly into your ear.

- 14 -
3. When the dome is placed correctly, you
should not be able to see the thin tube
sticking out when facing a mirror.
Removal
1. Hold the thin tube with your thumb and
forefinger and pull the tube outward.
2. Consult hearing care professional if you
have difficulties removing the hearing aids.

- 15 -
Operation of hearing aid
Switch control
Volume control function: To increase volume
press then release the top part of the switch.
To decrease the volume, press then release
the bottom part
of the switch.
Memory switch
function:

- 16 -
Speech mode is the default programme. To
switch to next programme, holding the top
part of the switch for three seconds. The
programmes will be circulated from P1, P2,
P3 to P4.
Holding the down part of the switch for three
seconds. The programmes will be circulated
from P1, P4, P3 to P2.
You will hear one or more beeps.

- 17 -
The number of beeps indicates which
programme you have selected (one beep =
programme one, two beeps = programme
two, etc.).
When the hearing aid is turned off and then
back on, the hearing aid always returns to the
default setting (P1). Selected model will
returns to the program used last time.