Xilinx ML507 User manual
ML507
QuickStart
May 2008
Overview
•Setup
•Boot with ACE-loader ACE File
•Observe LCD and Terminal messages
•Load new Configuration
•Re-load ACE-loader
ML507 BSB Hardware
•The ML507 PPC440 design
hardware includes:
–PPC440MC DDR2 Interface
–External Memory Controller (EMC)
•ZBT SRAM
–BRAM
–Networking
–UART
–Interrupt Controller
–System ACE CF Interface
–GPIO (IIC, LEDs and LCD)
–PLB Arbiter
Note: Presentation applies to the ML507
Additional Setup Details
•Refer to ml505_overview_setup document for details on:
–Software Requirements
–ML507 Board Setup
•Equipment and Cables
•Software
•Network
–Terminal Programs
•This presentation requires the
9600-8-N-1 Baud terminal setup
Note: Presentation applies to the ML507
Hardware Setup
•Connect the Xilinx Parallel
Cable IV (PC4) to the
ML507 board
•Connect the RS232 null
modem cable to the
ML507 board
Note: Presentation applies to the ML507
Hardware Setup
•The ML507 uses a DVI video
interface
•Connect a DVI monitor
or
•Use a DVI/VGA adapter
to connect a VGA monitor
–http://www.belkin.com
Note: Presentation applies to the ML507
Hardware Setup
•USB Keyboard
–www.dell.com
Note: Presentation applies to the ML507
Factory CompactFlash
•The CompactFlash shipped with the ML507 board has the
following ace files preloaded:
Note: Presentation applies to the ML507
Verify Factory Default Settings
•Set the Ethernet PHY jumpers, J22, J23 to positions 1-2 (1)
•Insert the Factory CompactFlash into the ML507 board (2)
•Set the Front DIP switches (SW3) to 00010101 (1 = ON) (3)
•Set the Rear DIP switches (SW6) to 11001010 (4)
•Power-up the ML507 board
4
Note: Presentation applies to the ML507
2
3
1
Bootload
•The bootload_video.ace loads:
Note: Presentation applies to the ML507
Bootload
•The terminal window also reflects the bootload application
•Use the left/center/right buttons to choose an application or type a
number in the terminal window
•After each demo, push the SysACE reset to return to bootload
Note: Presentation applies to the ML507
Slideshow
•Type 1, to launch the slideshow application in Configuration 1
•The slideshow loads the presentation into memory then presents it
Note: Presentation applies to the ML507
Slideshow
•The slideshow app will present a series of slides on the Monitor:
Note: Presentation applies to the ML507
Web Server
•Type 2, to launch the web server application in Configuration 2
–Note: You may need to turn off your browser's proxy and specify a direct
connection to the Internet in your browser options
Note: Host IP is 192.168.1.1, subnet mask is 255.255.255.0
Running the LWIP Demo
•Open a web browser to address 192.168.1.10
Running the LWIP Demo
•Click the Toggle LEDs button; view change on ML507
Simon
•Type 3, to launch the Simon application in Configuration 3
Note: Presentation applies to the ML507
Board Diagnostics
•Type 4, to launch the XROM application in Configuration 4
Note: Presentation applies to the ML507
Board Diagnostics
•XROM includes a series of board test routines
Note: Presentation applies to the ML507
USB Keyboard
•Type 5, to launch the USB Keyboard application in Configuration 5
•Type ML507 and view results:
Note: Attach keyboard after demo loads
Other manuals for ML507
1
Table of contents
Other Xilinx Motherboard manuals
Xilinx
Xilinx Virtex-4 RocketIO User manual
Xilinx
Xilinx VC709 User manual
Xilinx
Xilinx ML310 User manual
Xilinx
Xilinx KC705 User manual
Xilinx
Xilinx SP605 User manual
Xilinx
Xilinx VCU110 User manual
Xilinx
Xilinx XTP194 User manual
Xilinx
Xilinx AC701 User manual
Xilinx
Xilinx VC707 User manual
Xilinx
Xilinx Spartan-6 FPGA Series User manual
Xilinx
Xilinx M401 User manual
Xilinx
Xilinx EK-U1-VCU128-G-J User manual
Xilinx
Xilinx ML505 User manual
Xilinx
Xilinx VCU118 User manual
Xilinx
Xilinx AC701 User manual
Xilinx
Xilinx VCU118 User manual
Xilinx
Xilinx Spartan-6 FPGA Series Technical manual
Xilinx
Xilinx Zynq-7000 User manual
Xilinx
Xilinx Kintex UltraScale FPGA KCU1250 User manual
Xilinx
Xilinx VC709 Si570 Owner's manual
