Xilinx Zynq ultrascale+ zcu104 User manual

Zynq UltraScale+ MPSoC

ZCU104 Evaluation Kit

Quick Start Guide

This ZCU104 Evaluation Kit contains all the hardware, tools, and IP required to evaluate and develop your Zynq®

UltraScale+™ MPSoC design. The ZCU104 reVISION package provides out-of-box SDSoC™ development

environment software flow with OpenCV libraries, machine learning framework, and live sensor support.

Use this quick start guide to set up and configure the board, run the built-in self-test (BIST), install the Xilinx tools,

and redeem the license voucher. The guide also provides a link to additional design resources including reference

designs, schematics and user guides.

ZCU104 Evaluation Kit

For more information, visit www.xilinx.com/zcu104.

X-Ref Target - Figure 1-1

Power Supply and

Power Cables

Ethernet

and USB

Cables

ZCU104

Evaluation

Board

USB

Camera

Send Feedback

Built-In Self-Test (BIST) Instructions

ZCU104 Evaluation Kit

www.xilinx.com

STEP 1: Set Configuration Switches

Set mode switch SW6 to QSPI32.

Note: For this DIP switch, in relation to the arrow, moving the switch

toward the label ON is a 0. DIP switch labels 1 through 4 are equivalent to

MODE pins 0 through 3. Set DIP switches labeled 1 to 4 to ON, OFF, ON,

ON.

STEP 2: Connect Power

Plug the power supply into a power outlet with one of the included power

cords.

Connect the 6-pin power supply plug to J52.

Turn on the board power with the SW1 slide switch.

If the two rows of Power Good LEDs glow green, the power system is good.

VADJ (DS8) will not be on.

If the DONE LED (DS32) circled here glows green, the Zynq UltraScale+ device

has configured successfully.

STEP 3: Initiate Configuration

The built-in self-test (BIST) starts shortly after power on.

Note: Pressing the POR_B (SW4) or the SRST_B (SW3) button causes the

DONE LED to go out, the device to configure again, and the BIST to

restart.

The PL GPIO LEDs flash on and off several times at the start of the BIST.

Boot Mode Mode Pins [0:3]

QSPI32 1234

0100

DONE

LED

Power

Good

LEDs

SW4 SW3

Send Feedback

www.xilinx.com

Self-Test Assignments for PL LEDs

STEP 4: Run the Built-In Self-Test

The BIST consists of a set of pass/fail tests that run sequentially. As each test passes, its corresponding LED glows

green. If a test fails, its corresponding PL GPIO LED is off. The test status LEDs are next to each pushbutton (PB). For

SW13, up is ON or 1.

Note: To pass the PL DIP test, all the switches in SW13 must be up before any of them are moved down. The

LEDs flash faster after you begin the DIP or pushbutton (PB) test.

• The Clock, BRAM, PL-DDR4, EEPROM, and I2C tests run without user input.

• The DIP switch test (SW13) waits for you to move all the DIP switches toward the label ON, and then back.

• The PB test waits for you to push all the pushbuttons (SW14, SW15, SW17, and SW18). The pushbuttons can

be pushed in any order. The LEDs are by the pushbuttons.

• The LED for the test that is waiting for your input blinks.

MSB→LSB

LED 3 - Top Left LED 2 - Top right LED 1 - Bottom left LED 0 - Bottom right

Clocking and Memory EEPROM and IIC DIP Switch Pushbuttons

X-Ref Target - Figure 1-2

Photo can vary from product. SW1 (Power-On) J52 (12V Power)

SW4 (POR_B)

SW6

Power Good LEDs

DONE LED

PL DIP (SW13)

PB Switches

(SW18, SW17

SW15, SW14)

Send Feedback

XTP482 (v2.1) May 30, 2018

Install Xilinx Tools and Redeem the License Voucher

A SDSoC development environment voucher code is included with the ZCU104 Evaluation Kit. This license is

node-locked and device-locked to the XCZU7EV device.

STEP 5: Redeem the SDSoC Development Environment License Voucher

To redeem the voucher code, go to www.xilinx.com/getlicense and enter the voucher code shown on the Quick Start

Guide in your kit. After it is redeemed, the licenses appear in your entitlement account, and you can generate a

license file, which will be emailed to you. For additional assistance redeeming your voucher, go to www.xilinx.com/

kits/voucher.

Note: This code can only be used once and must be redeemed within one year of purchase.

STEP 6: Getting Started

To get started, see this ZCU104 Getting Started github site

https://github.com/Xilinx/ZCU104-reVISION-Getting-Started.

Next Steps

Learn More

For additional information on using responsive and reconfigurable vision systems (reVISION), see

www.xilinx.com/products/design-tools/embedded-vision-zone.html. Also see the H.264/H.265 Video Codec Unit

LogiCORE IP Product Guide (PG252).

Support

For support options related to this product, see the Xilinx Support website at www.xilinx.com/support.

Warranty

For the product warranty, go to www.xilinx.com/kits/warranty.

herein are trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective owners.

X-Ref Target - Figure 1-3

,PSRUWDQW

Send Feedback

Other manuals for Zynq UltraScale+ ZCU104

Table of contents

Other Xilinx Motherboard manuals

Xilinx

Xilinx VC707 User manual

Xilinx

Xilinx EK-U1-VCU128-G-J User manual

Xilinx

Xilinx Zynq UltraScale+ ZCU104 User manual

Xilinx

Xilinx SP601 User manual

Xilinx

Xilinx Virtex-II Pro ML324 User manual

Xilinx

Xilinx ZC702 User manual

Xilinx

Xilinx ML310 User manual

Xilinx

Xilinx Kintex UltraScale KCU1500 User manual

Xilinx

Xilinx KCU105 User manual

Xilinx

Xilinx ZC702 Si570 Installation guide

Xilinx

Xilinx ZC702 User manual

Xilinx

Xilinx Zynq UltraScale+ ZCU208 User manual

Xilinx

Xilinx AC701 User manual

Xilinx

Xilinx Kintex-7 FPGA KC705 User manual

Xilinx

Xilinx Zynq ZC702-G User manual

Xilinx

Xilinx SP701 User manual

Xilinx

Xilinx Virtex-7 FPGA VC7222 IBERT User manual

Xilinx

Xilinx ZCU102 User manual

Xilinx

Xilinx Zynq-7000 ZC702 User manual

Xilinx

Xilinx Spartan-7 SP701 User manual

Xilinx

Xilinx Spartan-3E User manual

Xilinx

Xilinx HW-130 User manual

Xilinx

Xilinx ZCU106 Operating and maintenance instructions

Xilinx

Xilinx ML505 User manual

Popular Motherboard manuals by other brands

Gigabyte

Gigabyte MNJ190I-FH user manual

Biostar

Biostar HI-FI-Z87X-3D Setup manual

Atmel

Atmel SAM9753PIA-DK user guide

Coapt

Coapt GEN2 Handbook

Supero

Supero SUPER P4DL6 user manual

Cypress

Cypress CY3210-PSoCEVAL1 quick start guide

ASROCK

ASROCK B660M-HDV manual

Fujitsu

Fujitsu D2831 Short description

Industrial Computers

Industrial Computers ADE-6050 user manual

Asus

Asus TUF Z270 MARK 2 manual

DFI

DFI NB71-BC user manual

ASROCK

ASROCK H61 Pro BTC user manual

Norco

Norco POS-7893 user manual

Intel

Intel DG965MS specification

Asus

Asus B85M-VIEW PAKER user manual

Asus

Asus P5G41T-M LX V2 user manual

Gigabyte

Gigabyte GA-K8VT800-RH user manual

Gigabyte

Gigabyte Z790M AORUS ELITE user manual