Xomax 2DTSBN6000 User manual

Please read all instructions carefully before using
2DTSBN6000

02
INSTRUCTIONSINSTRUCTIONS
15
Trouble shooting
PROBLEM CAUSE CORRECT ACTION
Poor performance
of radio station
Connot load disk There is a disk inside Eject disk,then,slot in new disc.
After ignition
switch off ,setting
information all lose
Reset information and save
Change battery or fuse
Cannot power on
Check whether power fuse
melt or not Change fuse same as the old one
Some factors cause MPU wrong
operation
Press RES button on the panel by pen
point, then, power on
Weak signal Move the car to another place, then
research
Cannot play disc
Disc is scratched Change new disc
Put wrong side of disc into
the unit Slot in the disk with sign side up
Clean lens by lens clean discLens has dirty
Cannot switch
language/subtitle
There is only one language/
subtitle in disc
If disc is not with multi-language/
subtitle, it cannot switch language/
subtitle
No image Other factors cause MPU
wrong operation
Press [RES] button on the panel by
penpoint, then, power on
Cannot watch
image during
driving
It’s not allowed to watch image
during driving
Park the car in a safe place, put the car
stall in “ P ”postion, pull up the hand
brake
CONTENTS
NOTE
instructions will not enjoy the warranty.
2. To drive safely and avoid break the traffic rules, do not watch program and operate the unit
while driving.
3. To avoid short circuit, please do not exposure the device to rain.
4. To avoid short circuit, please do not put in the device or any metal objects left behind.
5. Not open the machine for maintenance by yourself, please go to the professional repair
service station for repairing.
6. When the engine is turned off, please do not use the car audio a long time, otherwise the
battery may run out.
7. Do not insert anything to the device’s vent and other openings.
8. Damage to the screen carefully! Do not use sharp objects push, rub, Stroke the screen.
1. Please read the instructions before using the unit, the damage caused by not following the
Panel Introduction 03
Remote controller operation 05
Turn on/off Host 07
Access main interface 07
U Disc/SD Card function operation 07
Radio Function Operation 07
Disc Function Operation 09
Bluetooth Function Operation 10
External input operation (Optional) 11
GPS Navigation Function Operation 12
Other functions 12
Foreground/background Setup 13
Sound Setup 13
Navigation Path Setup 13
Language Setup 13
Radio Area Setup 13
Backlight 14
Touch Screen Calibration 14
Steering Wheel Setup 14
Time setup 14
Trouble shooting 15

INSTRUCTIONSINSTRUCTIONS
0314
Backlight
Via backlight setup interface, you can manually adjust the display screen brightness according
to the intensity of light of the environment to achieve satisfactory effect.
Touch Screen Calibration
If errors occur in touch position, you can calibrate touch coordinates.
Enter touch calibration interface, Use a touch pen to click the central area of symbol “+”,
calibrate the screen in the moving sequence of the central area of “+”. After calibration is
completed, system will automatically save data and exit the screen.
Steering Wheel Setup
You can also perform control to the unit by the steering wheel of the car. Connect the positive
and negative terminal of the car SWC cable with the positive and negative terminal of the SWC
cable of the unit respectively.
Click buttons on the steering wheel one by one and keep a record of relevant sequences. Click
appropriate function setup to save the settings.
Time setup
Touch [Time] icon in the main interface to enter into the
calendar setup interface. Click the display position of year/
month/day/hour/minute to reset the current parameters.
Set in the time interface touch 12HR/24HR icon to switch
between clock modes.
Panel Function
1. SRC button
When the power on, press this button to turn on/off host; in any application procedure,
press this button can switch to the main interface.
2.MODE button
When the unit is power on, Repeat press this button can switch to different function
mode as following picture.
Note: When the device without
connecting to USB, SD, CDC or DVD
no disc inside, the system will
automatically skip these related
working mode.
3.FM/AM button
In any mode, press the button to radio mode.
In radio mode, press the button to switch band.
4. AUX IN
To input external audio.
5.RESET
Press this button can back to default mode.
6.
Press this button can eject the disc.
7.EQ button
In a source mode, press the button to enter equalizer setup.
8.DVD button
In any mode, press this button to read the disc.
9.NAVI button
Press the button to enter into/exit navigation interface.
CDC
AUX
SD
USB
DVD
RAD IO
TV
GPS
(Op tional)
(Op tional)
(Op tional)
(Op tional)

INSTRUCTIONSINSTRUCTIONS
1304
Access setup interface
Click [Setup] icon on main interface to access setup interface. Touch each function icon to enter
into the corresponding function operation.
Foreground/background Setup
You can enable background mode by foreground/background setup. When the unit is
connected with background device, you can enable background mode of the unit to play audio
and video files. At the Set interface Touch [Foreground/background] icon, Enter into
foreground/background setup interface. Only in radio/bluetooth/navigation mode can
background mode be enabled.
Sound Setup
Touch [Sound Setup] icon to enter sound setup interface.
Sound effect setup: select general, pop, classic or rock, you can adjust to the best audio effect
according to your preferences.
System volume: adjust volume level of the whole unit.
Bluetooth volume: adjust volume level of bluetooth mode.
Navigation volume: adjust volume level of navigation mode.
Reverse volume: adjust volume level of reverse mode.
Screen click sound: select to turn screen click sound on/off. After click sound is turned off,
there is no beep sound when you touch the screen.
Loudness: Select the turn on/off loudness function.
Tweeter/woofer/subwoofer: adjust volume level of tweeter/woofer/subwoofer.
Left front speaker attenuate: adjust volume level of left front speaker.
Right front speaker attenuate: adjust volume level of right front speaker.
Left rear speaker attenuate: adjust volume level of left rear speaker.
Right rear speaker attenuate: adjust volume level of right rear speaker.
Navigation Path Setup
Navigation path is already set when you buy the product. Do not enter into the navigation
setup interface to change path arbitrarily. Otherwise you may cause navigation program
abnormal.
Language Setup
During use, you can select your familiar language to display menu by language setup.
At the language set interface click appropriate language icon, the selected language will be
displayed as the menu language.
Radio Area Setup
You need to select your radio area before you use radio function.
10.SD slot
Connect the SD memory card to this socket, and the unit can play MP3 music.
11.USB slot
Connect the USB memory to this socket, and the unit can play music format files
supported by this unit in the USB memory.
12.Disk load slot
Opening for disks to enter or retreat.
13.MUTE button
Press this button to shut off the sound output, re-press this button can resume the
sound output, long press this button can turn off the TFT LCD display.
14.IR
To receive infrared signals from the remote control matched with the unit.
15. MIC
Input socket for microphone.
16.MAP slot
Insert map card to read navigation map data.

INSTRUCTIONSINSTRUCTIONS
0512
1
GPS Navigation Function Operation
In tune
Among tall buildings
At the boulevard
The antenna is sheltered
Underground parking
Overpass or viaduct
Navigation Function Operation
For detailed operation of navigation function, see “Navigation Operation Manual”.
Receiving signal error
When the satellite signals can be normally received, the error of standard GPS shall be about
7 meters. Driving on parallel sections, there shall be error even the product has auto-correct
function. The normal receiving of satellite signals shall be affected and cause error in
following environment:
2
Other functions
Rearview function
In any running state, the video signal can switch to reverse video state when reversing the car,
and the system shall return to its initial running state after reversing the car.
Do not rely on CCD system completely, please make sure your car is safe by your eyes during
driving. Back rearview system only assists in driving. As the distance range of rearview system
is limited, completely relying on the rearview system during driving may cause accidents.
Reverse field simulation Rearview backup image
Warning

INSTRUCTIONSINSTRUCTIONS
1106
Bluetooth music playback
Bluetooth player can play music files in cellphone via
wireless audio device on condition that the cellphone
supports relevant bluetooth protocol. After bluetooth device
gets connected to the unit, audio system will automatically
link with the paired cellphone. In some cases, you need to
enable the playback of audio files by phone keypad due to
different phone models. Play/pass
the previous/next song
Stop
External input operation (Optional)
Connect the video input plug with external video input jack, and connect the audio input plug
with external audio input jack.
Touch [Input] icon on main interface to access external input interface.

INSTRUCTIONSINSTRUCTIONS
0710
Bluetooth Function Operation
The system provides bluetooth handsfree communication function, if your cellphone supports
bluetooth function, you can establish a point-to-point connection between your cellphone and
the system. The system can also achieve the dialing, answering function, A2DP, the function of
phonebook on the screen.
Pair/link
The first time you pair your cellphone with the unit, the procedures below should be followed:
① Turn the bluetooth function of your cellphone on.
②The cell phone searches for bluetooth device and connect.
③A prompt is displayed on the screen of the phone, to accept pair, enter the same numeric code
on the phone (0000) and press [OK] button.
④ After the pair is completed, the name of the connected cellphone is displayed on the screen.
⑤ After recharged, the bluetooth system will automatically get connect to the lastly
disconnected cellphone.
Turn on/off Host
When the ignition switch is put in ACC or ON position, Press[ ] button on the front panel to
turn on the unit. After the host starts, hold [ ]button for 3 seconds , the host will turn off.
Access main interface
In boot-up state, press /SRC/MENU button on the panel to switch to main interface.
Touch
page. Touch the icon does not go into a long free mobile icon location. Touch the icons to enter
the corresponding functions. Touch in two different interface style to switch between.
icon or at the touch pen / finger gently sliding the screen to switch the main menu
Rear view function menu (optional)
When the machine has a menu function, rear view, in the main screen, click icon to enter the
menu after reversing interface.
U Disc/SD Card function operation
When there is a USB device/SD card connected, the unit can conduct the playback of audio/
video/image files in the USB device/SD card.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit correctly
until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card and it
shall pop up after unlocking.
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen first, and
then take out the device.
Note: When the unit has front USB, only one of them.
Radio Function Operation
Touch [ RADIO ] icon in the main interface to enter into the radio interface.
Search/store station
1. Auto search and store station
(1) Touch [ ] icon in the radio interface on the panel
to search for station automatically. During search, the
searched stations will be stored automatically.
(2) During search, retouch [ ] icon to stop auto
searching.
Phonebook
After the cellphone gets connected to the unit, you can read
records in the phonebook of your cellphone and store
information in the phonebook of the unit.
phones may not support the phone book.)
( Note: Some
Call records
Recent dialed calls, received calls and missed calls can be
saved in call records. Select missed/dialed/
received calls
Clear all
After the successful pair, the bluetooth that indicates
connecting status will be lighted, otherwise, it will appear
dimmed.
Touch [Disconnect] to disconnect the current connection; after
disconnected。
Touch [Connect] to connect the disconnected bluetooth device.
Touch [Reset] icon to clear all pair records.
Bluetooth Interface Function Introduction
Dial
Call records
Phonebook
Music playback
Switch

INSTRUCTIONSINSTRUCTIONS
0908
Disc Function Operation
Play/eject disc
Insert the disc into the disc slot with the printing surface up,
system will detect the disc and automatically take it in to
read and play.
Click button on the panel to eject the disc.
If a disc has not been took away 15 seconds after it is ejected,
system will automatically take in the disc but not play.
Note: Do not insert two discs or more.
Playback Menu
During playback of disc, touch the middle lower area of the
screen to pop up the touch menu, operate the touch menu to
perform various playback controls.
Note: Touch the top left corner of the screen to return to the main interface.
DVD/VCD disc playback
When there is a disc in the unit, touch icon in the main interface, system enters into disc
reading status. When the disc does not have play menu, system will automatically read the disc
and directly play; when the disc has play menu, system displays DVD menu, you can touch
appropriate options on the screen to access the corresponding items.
CD Disc Playback
When there is a disc in the unit, touch icon in the main interface, system enters into disc
reading status. After disc format is read, the screen will display the CD playback interface,
system will automatically read the disc contents and display on the screen, You can directly click
song name to select and play, you can also click the numeric keypad button and enter song
number to selected your favorite song to play.
MP3/WMA format disc playback
Put the MP3/WMA disc in DVD player, after the disc is read, system enters into the interface as
is shown below:
Touch the file name icon and the song to read and play. Touch
to select the previous/next file.
Playback control function keys and DVD Play control keys are
functioning.
Play/pause Stop
The songprevious/next
Fast /backward forward
Repeat/Repeat all discs
settings
002 Big big world
001 \
003 My Heart
001 My Heart 1.MP3
002 My Heart 1.MP3
003 My Heart 1.MP3
004 My Heart 1.MP3
005 My Heart 1.MP3
1 2 34
2. Manual search and store station
(1) Finger / touch pen drag of high radio frequency scale can be achieved manually search for
radio stations. During search, after a station is searched, the unit will stop searching
automatically and play the searched station radio.
(2) Directly touch[ / ] icon in the radio interface to fine-tune station frequency.
(3) After a station is searched, (such as: 88.15MHZ), long press any position in the pre-stored
station list in the radio main interface, the searched station will be stored in the selected position.
(4) FM band can save 18 stations (Fm1/FM2/FM3 can each save 6), AM band can save 12 stations
(AM1/AM2 can each save 6).
(5) During search, the unit will automatically stop searching after it has searched for all stations
through once.
3. Select station/band switch/switch between LOC/DX
(1) Directly touch any station in the pre-stored station list in radio interface to play the selected
station.
(2) Touch button in radio interface to switch band among Fm1,FM2, FM3, AM1 and AM2.
(3) Touch icon to switch search mode between LOC and DX. When LOC function is turned
on, only those radio stations with strong signals and good reception can be received; When DX
function is turned on, distant weak radio signals can be received.
4. RDS function
RDS provides a series of information (such as traffic information and station name), and can
automatically switch to a station with strong signals and carries the same program.
RDS data contains the following contents:
P1---program identification TA---traffic announcement PS---program service name
PTY---program type name AF---alternative frequencies EON---enhanced other network
TP---traffic program
Touch the upper right corner [RDS] radio interface icon, enter the RDS interface:
Function Operation
① TA ( Receive traffic information )
ON: When the traffic station is turned on, the radio will
automatically search for traffic stations. After a station is
searched, screen displays “TP”. Only when traffic information
is broadcasted can it be received, after traffic information is
completed, the radio will automatically switch to the previous
mode.
OFF: Repress [TA] button to close TA function. In other modes, traffic announcement will
automatically switch to radio mode, after the traffic announcement is completed, it will
automatically switch to the previous mode.
② AF
Touch the button to turn the AF function on/off. AF function is turned on, When the received
station signals become weak, the radio will automatically fine-tune to other frequencies. When
receiving an emergency announcing, the screen will display warning message “ALARM“.
③ EON
ON: Open EON function, another AF list is received. OFF: Close EON function.
④ REG
ON: Open REG function, only local RDS stations can be received. OFF: Close REG function.