XPOtool 63122 User manual

Operation Manual
Ash Vacuum Cleaner 20 Litres
63122
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

https://www.XPOtool.com Item 63122 Page 2
The Tool Experts
12 2021-1
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]
To return orders for exchange, repair, or other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

https://www.XPOtool.com Item 63122 Page 3
The Tool Experts
12 2021-1
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
About the product
•The ash vacuum cleaner is used to remove cold, dry ash from fireplaces or barbecue trays. The
large container and flexible hose allow thorough cleaning of hard-to-reach places. The vacuum
cleaner is equipped with a replaceable air filter. The product is not intended for commercial use.
The correct, reliable, and safe operation of the device depends on its proper use.
•Before working with the device, read the entire manual and follow all instructions and directions
contained therein.
•No responsibility will be accepted for damage or injury caused by failure to observe the safety
regulations and instructions in this manual.
•The unit is supplied in complete condition and requires no assembly. Additionally, included in
the delivery is an elastic hose as well as an aluminium suction nozzle.
Safety instructions
•This device is not intended for use by persons with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning proper use of the device by a person familiar with it and responsible
for their safety.
•Children must not use the device and must be supervised if near it to ensure that they do not
play with it. Cleaning and maintenance work by children should not be carried out without
supervision.
•The ash vacuum cleaner is intended for dry operation. Sucking up water, wet ash or other
wet waste materials is prohibited. This creates a risk of electric shock, which may result in a
health hazard to the user or uninvolved persons.
•Never vacuum hot, glowing or burning objects. This may cause a fire or explosion and result
in serious injury or death to the user. The maximum temperature of the impurities to be vac-
uumed must not exceed 40 ℃.
•The device is intended for indoor use and must not be exposed to the effects of water, in-
cluding rain.
•Before connecting the power plug to the mains, make sure that the parameters of the power
supply match those on the name plate.
•Before each use, check the condition of the unit, power cable, and power plug. If any defects
are found, do not operate the unit. Have any defects rectified by an appropriate specialist
company.
•Always disconnect the unit from the mains before carrying out maintenance work.
•Store the unit in a place not accessible to uninvolved persons, especially children. Even dur-
ing functional operation, make sure that the unit is stored in a place inaccessible to uninvolved
persons, especially children.
•The unit must be carried by the handle, not by the power cable.
•When the device is used as a blower, do not point the hose outlet at people or animals.
•Wear protective goggles and gloves during use.
•Regularly check the condition of the hose. Do not use the device with a damaged hose.

https://www.XPOtool.com Item 63122 Page 4
The Tool Experts
12 2021-1
Technical data
Mains voltage (V)
230
Mains frequency (㎐)
50
Rated power (W)
800
Hose length (㎝)
100
Length of suction nozzle (㎝)
23
Container volume (ℓ)
20
Protection class
II
IP code
IPX0
Parts list
№
Name
1
Tank
2
Cover
3
Cover latch
4
Holder
5
Switch
6
Power cord with plug
7
Inlet
8
Socket
9
Flexible hose
10
Suction nozzle
11
Air filter
12
Fabric air filter
13
Wheel
Operating the unit
Preparing for operation
•First check the container of the vacuum cleaner and clean it of waste material if necessary.
Then check the condition of the filters. The ash vacuum cleaner has two types of filters: a rigid
one equipped with a rubber seal and a fabric filter. When dirty, the filters must be cleaned using
compressed air at no more than 3 bar pressure. If the contamination cannot be removed from
the filters, the filters must be replaced with new ones. Check the condition of the seal integrated
at the upper edge of the rigid filter. If it is damaged, the filter must be replaced with a new one.
Notice! It is forbidden to operate the vacuum cleaner without a properly fitted air filter. This may damage
the vacuum cleaner and increases the risk of electric shock.

https://www.XPOtool.com Item 63122 Page 5
The Tool Experts
12 2021-1
Small wheels can be attached to the baseplate
of the vacuum cleaner. For this purpose, the pin
of the wheels must be pressed into the opening
of the baseplate.
There is a small metal chain on the bottom of the
container. Check that it is in contact with the
base during operation, as this can dissipate
electrical charge that has built up during opera-
tion.
The fabric filter is pulled over the rigid filter so
that the fabric filter surrounds the rigid filter at the
top.
The filters are to be attached to the lower side of
the cover so that the seal of the stiff filter fits
evenly. The gasket integrated at the top of the
filter has a flange that allows the filter to be se-
curely fastened.

https://www.XPOtool.com Item 63122 Page 6
The Tool Experts
12 2021-1
Mount the cover on the upper edge of the vac-
uum cleaner tank so that it fits around the entire
circumference. Press the cover onto the tank us-
ing the snaps. There are two marked points on
the cover that help make this connection com-
pletely tight.
Connect the elastic hose to the inlet. The hose
connector must be inserted into the hole so that
its notches align with the bulges of the inlet, and
then turned in the direction of the arrow marked
“lock.” Make sure that the hose does not slip out
of the hole during operation.
To remove the inner part, turn its connector in
the direction of the arrow marked “LOOSE” and
then pull the connector out of the inlet.
Connect the suction nozzle to the loose end of
the hose by inserting it into the hose connector.
The vacuum cleaner also offers the possibility to
connect a hose to the outlet so that it can also
be used as a blower. The hose is connected to
the connector by pressing the socket.

https://www.XPOtool.com Item 63122 Page 7
The Tool Experts
12 2021-1
Commissioning
Attention! Sucking up hot ash is prohibited. The temperature of the suction material must not exceed
40 ℃.
•Make sure that all preparatory activities have been carried out.
•Likewise, make sure that the vacuum cleaner switch is set to “O” (off).
•Now insert the plug of the power cord into the mains socket, then set the switch to “I” (on).
•After finishing work and before maintenance work, switch the vacuum cleaner off again at the
switch and pull out the plug.
Notice! When using the vacuum cleaner as a blower, make sure that the container has been emptied
and the filter cleaned or replaced with a new one. There is a risk of debris remaining in the container
being blown out through the outlet opening.
Maintenance
Note! Pull out the plug before maintenance work!
•After each use of the vacuum cleaner, the container, the cover seal and the air filter must be
checked as described in these instructions.
•The ash vacuum cleaner is cleaned from the outside with compressed air of no more than
3bar pressure. Special attention should be paid to the ventilation openings of both the supply
and exhaust air. If necessary, clean them of all obstructions with compressed air of no more
than 3 bar. Do not use sharp metal objects to clean the ventilation openings.
•Do not immerse the ash vacuum cleaner in water for cleaning.
•The vacuum cleaner hose must be checked for damage before and after use. It is forbidden
to use a damaged hose. Major soiling of the housing should be removed with a soft cloth.

https://www.XPOtool.com Item 63122 Page 8
The Tool Experts
12 2021-1
Disposal regulations
EU guidelines regarding the disposal of scrap electric devices (WEEE, 2012/19/EU) were implemented
in the law related to electrical and electronic equipment and devices.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-
registration number DE45283704.
Disposal of used electrical and electronic devices (in-
tended for use in the countries of the European Union
and other European countries with a separate collec-
tion system for these devices).
The logo on the article or on its packaging points out
that this article must not be treated as normal house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment.
By contributing to the correct disposal of this article you
protect the environment and the health of your fellow
men. Environment and health are threatened by inap-
propriate disposal.
Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal waste
disposal facilities, or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.