XTREME TECHNOLOGIES X-BT-01 User manual

Xtreme Technologies Corporation
Summary
Part Description Bluetoooth Radio Module
34 x 15 mm SMT
Xtreme Part Number X BT 01
FCC ID # Y3TE05
Proprietary Notice
These documents, and the contained information herein, are proprietary and are not to be reproduced,
used or disclosed to others for manufacture or for any other purpose, except as specifically authorized,
in writing, by Xtreme Technologies Corp.
FCC Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance. This
transmitter must not be co located or operating in conjunction with any other antenna or transmitter.
Notice: Any changes or modification not expressly approved by the party responsible could void the
user’s authority to operate the device. This device complies with part 15 of the FCC Rules. Operation is
subject to the following three conditions: (1) This device may not cause harmful interference, and(2) this
device must accept any interference received, including interference that may cause undesired
operation.
This device operates at a transmission rate of 1Mbps, and only use the GFSK modulation.
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9

Xtreme Technologies Corporation
Device Features
•Fully qualified Bluetooth 2.1/2.0/1.2/1.1 module
•Bluetooth v2.1 support
•UART (SPP or HCI) and USB (HCI only) data connection interfaces.
•Embedded Bluetooth stack profiles included GAP, SDP, RFCOMM and L2CAP protocols, with SPP
and DUN profile support.
•Bluetooth SIG certified
•Castellated SMT pads for easy and reliable PCB mounting
•Internal daughter card with track antenna
•Certifications: FCC, IC, CE
•Environmentally friendly, RoHS compliant
Applications
•Cable replacement
•Barcode scanners
•Measurement and monitoring systems
•Industrial sensors and controls
•Medical devices
•Handsfree/handset devices
•Computer accessories
•PCs, PDAs, Printers
Block Diagram
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9
CSR BLUECORE 04
External
Balun
Xtal 8M Flash
UART/USB
SPI
PCM
PIO
3.3V

Xtreme Technologies Corporation
Description
The X BT 01 Bluetooth module is a complete Bluetooth system. It utilizes the CSR BC04 chip set with
external programmable flash memory. It is a cost effective, short range, certified Bluetooth radio
designed to be embedded into any electronic devices requiring Bluetooth communications.
The module features 8Mbit of programmable flash memory allowing custom bluetooth appliations to
be programmed to the device. The module contains all other required radio elements: antenna and
supporting circuitry. Embedding the X BT 01 module into a product is a simple process.
This is a Class 2 Bluetooth Power Device.
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9
Bluetooth Specification Version 2.0
Frequency Band 2.4Ghz ISM
Form Factor Internal augter Card With PCB Antenna
Interface UART/USB, PCM, PIO, SPI
Receive Sensitivity <= -82dBm
Maximum Output Power +4dBm (Class 2)
Operating Voltage
Operating Temperature
Storage Temperature
Standby Current
Operating Current 25mA
Search & Transmit Current 40mA
Range 10 m
Package Size 27.7(L) * 15.0(W) * 2.6(H) mm
3.3 ± 0.1 V
--40 ~ +80oC
--40 ~ +80oC
8mA (Standby current can decrease to µA when low power mode enabled)

Xtreme Technologies Corporation
Module Footprint
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9

Xtreme Technologies Corporation
Dimensions (mm)
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9

Xtreme Technologies Corporation
Additional Considerations
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the followingmeasures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver.
Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
TO OEM installer:
1. FCC ID label on the final system must be labeled with "Contains FCC ID: Y3TE05" or "Contains
transmitter module FCC ID: Y3TE05".
2. In the user manual, final system integrator must be ensure that there is no instruction provided in the
user manual to install or remove the transmitter module.
3. Transmitter module must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product. This device complies
with the following radio frequency and safety standards.
The user manual of the final host system must contain the following statements:
USA - Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC ules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, (2) this device must accept any
interference received, including interference that may cause
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9

Xtreme Technologies Corporation
undesired operation and (3) this device operates at a transmission
rate of 1Mbps. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
Caution: Exposure to adio Frequency adiation.
This device must not be co-located or operating in conjunction with
any other antenna or transmitter.
The modular transmitter will be labeled with its own ID. Also the OEM host computer manufacturer
will be informed to display a label referring to the enclosed module. The label on the final system must
be labeled with “Contains IC: 8324A E05”.
This device complies with RSS 210 of Industry Canada.
"Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device."
"This Class B digital apparatus complies wtih Canadian ICES 003."
"Cet appareil numérique de la classe B est conforme à la norme NMB 003 du Canada."
Xtreme Technologies Corporation
200 - 4616 Valiant DR NW +1.40 .668.016
Calgary, AB, Canada [email protected]
T A 0X9