Xtron XT-WG02 User manual

Manual X-TRON XT-WG02 Wireless Video Doorphone
The wireless video door phone is a 2.4G wireless high-tech household intelligent product
integrating doorbell, photo-taking, intercom,monitor and unlocking functions into one.
Especially is its unique human body detection function, when visitor is in its detection
range, the indoor monitor shall be activated, show the image of the outdoor on its screen
and take photo automatically. Therefore, even you were not at home, you also could know
who visited you. This model is the guarantee for your home security.
This product does not use wires. It is convenient to install and simple to use. It’s specially
designed for villas. A outdoor unit can work with three matched handsets with max.
working distance 300 meters in an open area.
Adopting the latest energy saving technology, its stable performance and fashionable
apperance design make it the first choice of your high-quality intelligent life.
Introduction……………………………………………………………………………..........
Safety Warnings & Attentions………………………………………………………………
Product Overview……………………………………………………………………………
Product Diagram …………………………………………………………………………
Installation Guide …..………………………………………………………………………
Installation outdoor unit….……………………… ………………………………
Installation indoor monitor.………….………….…………………………………………
Starting Up & shutting down…..……………………………………………
Menu Setting………………………………………………………………………………..
Date &Time Setting…………………………………………………………………………
Ringing Setting…………………………………………………………………………..…
Lock delay Setting……………………………………………………………………..…
PIR Setting……………………………………………………………………………..…
Call and Answer…………………….…………………………………………
Indoor monitor. View Outdoor Unit…………………………………………..…
Unlock the door…………………………………………………………………………..
Take a photo…………………………………………………………………………..
Night-Vision………………………………………………………………………………..
Exposure Adjustment………………………….……………………………………………
Photo-preview & Delete…………………………………………………………………
Battery & charge………………………….…………………..…………………………..…
Configuration…………………………….…………………..…………………………..…
Statement………………………………………………………………………………..…
General faults and solutions…………………………………………………………..…

Introduction
Thank you for choosing this wireless video door phone. Please read this Manual
carefully to fully understand its usage, perfect functions and simple operation.
The company reserves the right to modify this Manual from time to time without prior
notice.
Safety Warning & Attention
1. Attention
lDo not place this product on an uneven or unstable table-board to prevent failure or
damage caused by falling.
lOnly the battery and charger designated by the Company can be used on this
product. Application of other products may lead to leakage, overheating, blowout
and fire of the battery.
lDo not violently strike, shake or toss the wireless video door phone to prevent
failure and fire caused to the wireless video door phone.
lDo not put battery, charger or wireless video door phone in the microwave over or
high-pressure device; otherwise, damage and fire of electrical circuit and other
accidents may be caused.
lDo not use this product in a place with flammable and explosive gas; otherwise,
amount of dust; otherwise, product failure may be caused.
2. Attention for operation of this product
lDo not apply force on LCD screen or knock other objects with it, otherwise,
breakage and damage of LCD panel and seepage of crystalline liquid will be caused.
If the crystalline liquid enters your eyes, there will be danger of ablepsia. Wash your
eyes (be sure not rub your eyes) and go to see the doctor immediately.
lDo not dismantle or remodel this product, otherwise, damage, creepage and
electrical fault may be caused to this product.
lDo not press the keys with a pin, stump of pen/pencil and other keen-edged objects;
otherwise, damage or mis-operation will be caused.
lPlace tiny metal objects such as drawing pin at a place far away from the speaker.
As the speaker has magnetic property while working, it will attract these tiny metal
objects, which may lead to personal injuries or damage of the speaker.
lDo not press the terminal of lens at strong light source, such as the sun; otherwise,
damage of the image sensor may be caused.
lDo not press the terminal of lens with much force; otherwise, personal injuriy or
damage of the device may be caused.
3. Attention for operation of charger
You may charge the device with a charger or through a USB data line connected to the
computer.
Charge with matched alternate current; creepage, fire and damage of the door phone and
charger may be caused if other voltage is used.
It is forbidden to short circuit the charge, otherwise, electrical shock,smoke and damage
of the charger will be caused.
lDo not use the chager at the time when the power cord is damaged, otherwise, fire
and electrical shock will be caused.
lClear away the dust accumulated on power outlet ASAP.
lDo not place a vessel used to retain water beside the charger to prevent overheating,
creepage and failure of charger caused by spilling water.
lIf the charger is in contact with water or other liquids, disconnect the power supply
immediately to prevent overheating, fire electrical shock an dfailure of the charger.
lDo not dismantle or remodel this product, otherwise, damage, creepage and
electrical fault may becaused to this product.
lDo not use the charger in places with high humidity such as bathroom, otherwise,
electric shock, fire and damage of the charger will be caused.
lDo not touch the charger, electrical line and power outlet with wet hand(s),
otherwise, electric shock may be caused.
lDo not place heavy objects on the electrical line or refit the electrical line, otherwise,
electric shock and fire will be caused.
lBefore cleaning and maintenance, first pull the plug off the power outlet.
lGrasp the charger while pulling off the plug, as pulling the electrical line will lead
to damage of electrical line, electric shock and fire.

4. Operation and maintenance
●Please keep this product dry, as rainwater, moisture, humidity and liquids or
moisture content may contain mineral matters that erode the circuit.
●Do not keep this product in any place with high temperature. As high temperature
may shorten the lifespan of electronic device, damage the battery and cause
deformation or melting of certain plastic parts and components.
●Do not keep this product in any place with low temperature. As when being moved
from a place with low temperature to a place with normal temperature, it may
generate humidity inside, which may cause damage of circuit board.
●Do not attempt to dismantle this product. As improper handling by nonprofessional
personnel may cause damage of the device.
●Do not toss, knock or shake this product, as tough operation mode may damage the
motherboard inside the device.
●If this product is made wet by mistake, shut it down, remove the battery, and restart
the product after confirming it complete dry after 24 hours.
●Do not have the metal parts (specially configured interfaces of charger and data line
excluded) in contact with charger interface to avoid short circuit.
●Use clean and dry soft cloth to clean the lens, infrared lamp and light sensor.
！Warning: improper operation will void warranty!
Product Overview
一．Characteristics and application：
1. Fashion appearance —— adopt European design, full of modern science and
technology feeling, suitable for houses of various decorative styles.
2. Hidden antenna —— adopt built-in antenna design, protect the antenna effectively.
3. Extra large range of vision —— 120°wide field of view
4.Adjustable camera pan and tilt angle—up to 15°from center line in any direction—
to allow for mounting variations
5. High-resolution color LCD screen —— adopt 3.5-inch mainstream TFT digital LCD
screen, achieve outstanding clarity.
6. High speed transmission ---image transmission speed is 25fps, the image is clear and
fluent.
7. Infrared Night-Vision —— Camera has built-in IR LEDs for nighttime Operation
8.12 kinds of ringtones —— users can select the desired doorbells ringtones freely
9. Monitor function —— simple and convenient to use, view the outdoor scenes and take
photos just by pressing down one key.
10. Auto detection ——Camera includes a built-in PIR sensor that activates the camera
and takes photos of the visitor when he or she approaches
11. Intercom function —— can choose one-way or two-way talkback function.
12. Auto circulating memory ——100 photos auto circulating stored.
13.Unlock function—— Remotely and securely talk to visitors and unlock doors or gates
via the monitor
14. Multimachine extended function —— Connect up to two additional monitors
15. Long distance transmission —— communication distance can reach 300 meters in
open space.
16. AC/DC Power——Camera powered by AC9~16 V / DC5~16 V

二、Performance parameters:
Outdoor
unit
Power
Specific lithium battery BP-6M(1100mAh）
Consumption
400mA
Outline dimension
134*74*31mm
Weight
122g
Environmental condition
Temperature: -10~+50
Waterproof grade
IP55
Placement
Hang on outwall
Surface material
ABS & hardware accessories
Camera
300,000pixels
View angle
120° wide angle
Night vision pattern
Infrared lamps
PIR
3M*100°
Working time
3 hours continuously
Standby time
300hours
Charge time
3hours
External power
AC9~16 V/DC5~16 V
Indoor
monitor
Power
Specific lithium battery BP-6M(1100mAh）
Consumption
400mA
Outline dimension
126*84*20mm
Weight
110g
Environmental condition
Temperature: -0~+40
Placement
table style (handheld)
LCD size
3.5" TFT color screen
Wireless communication mode
2.4GHz
Images spread
25fps
Picture format
JPEG
Working time
4hours continuously
Standby time
500hours
Charge time
3hours
External power
DC5V 1A
Application distance
About 300m in open space

Diagram
A.ON/OFF
B.Switch button
for screen in
standby mode
C.Unlock
Charging indicator light
USB
Volume key
LED lamp
Up ↑
Down ↓
preview key
OK MIC
Display screen
Monitor key
Photo key
Time setup
Ringing setup
Lock delay
PIR setup
Indoor monitor
Table type charging station for handset:

Key introduction：
A. Indoor monitor Keys （7pcs Key）:
1. （OK key）: work as a off-hook key and a on-hook key; as a speaking key.
2. （↑UP key）: as an adjustment key for choosing.
3. （↓DOWN/ Preview key）: as an adjustment key for choosing when long press it;
as a preview key when short press it.
4. (monitor key): work as monitor key for standby mode
5. (FUNC Function key): as a multifunction key, such as a photo-taking key , a
time setting key, ringing setting key and a delete setting key.
6. Switch key "ON/OFF”: as a power "ON/OFF” key, the screen would be light when
short press it.
7. Volume key(+/-)
B. Outdoor unit keys
1. Doorbell key “Call”: ring the bell and trigger photo-taking there is no one on-hook.
2. Reset: match the communication code with the handset
Installation Guide
Position the camera so the area to be monitored is easily visible, optimally 5ft (1.5m)
above the ground. Do not position the camera in direct sunlight, or where it will be
exposed directly to rain or snow.
NOTE: For best results, the visitor should stand 2.5~5ft (0.8~1.5m) away from camera.
Installation Outdoor unit
1. Cut a hole large enough to run the min. 21AWG 2-conductor wire to the door unlock
device through the wall, as well as to the included power supply.
2. Install the camera bracket to the wall with three screws. Use screw anchors if the
bracket is mounted on drywall or brick.
3. Run the 2-conductor wire from the camera through the wire hole in the bracket to the
optional door unlock device.
4. Install the rechargeable lithium ion battery into the camera. The battery will act as a
backup power source in case of a power outage.
5. Connect the AC adapter (see Camera Wiring Diagram ).
6. Install the monitor battery and turn on the camera and monitor. If the camera is not in
the bracket, the tamper alarm will sound. Press the “OK”button on the monitor
repeatedly to disable the tamper alarm.

7. Experiment with the camera angle using the joystick on the camera back to adjust the
direction of the camera while viewing the image on the monitor.(see below)
8. Mount the camera into the bracket:
A. Push the top of the camera into the top of the bracket.
B. Push the bottom of the camera into the bottom of the bracket.
C. Screw in the bottom of the camera to fix the camera into the bracket and push the
plastic screw cover into the bottom of the bracket, over the screw.
NOTE: Do not block the PIR sensor on the camera.
1) Positive (+) power input. Connect to the red wire of the included AC adapter or to the
positive wire of the doorbell’s power supply.
2) Negative (-) power input. Connect to the black wire of the included AC adapter or to
the negative wire of the doorbell’s power supply.
3) Egress (N.O.) negative input. Connect to an optional N.O. egress device. The egress
device will activate the relay for the same length as the lock delay.
4) N.O. (Normally opened) output. Wire to the lock device for fail-secure operation.
5) N.C. (Normally closed) output. Wire to the lock device for fail-safe operation.
6) Common output. Wire to the power supply of the lock device.
NOTE: For 9~16VAC doorbell installation, wire directly from the doorbell ’s
transformer.

Installation indoor monitor
1. Parallel move the battery cover downward, and take it off.
2. Insert the lithium battery along the battery jar and set it level, mind the front and
reverse side of the battery.
3. Fit on the battery cover.
Starting Up & shutting down
Install battery to handset, long press “ON/OFF” about 3 seconds to start up (about 1
second after shutdown), logo shall be displayed on screen with a sound of “Beep”. Turn
into standby mode.
■Display: standby picture, signal sign, power sign, time & date
■In this mode, the screen gets dark after several seconds and turn into power saving
mode, the red LED flashes every 4 seconds. The screen would be lighted if press
again.
■When battery is in low power (≤1 bar), red LED flashes every one second. It
remains you to charge it.
■In standby mode, long press “Switch key” about 3 seconds to shut down.
Menu Setting
Press the “ON/OFF”button to turn display ON , long press “FUNC” key, enter into
menu setting. Then press “FUNC” key in sequence, it would respectively enter into
“ Time Setting”→“Ringing Setting”→“Lock Delay Setting”→“PIR Setting”.
Date & Time setting
nPress "↑/↓" key to choose the figure of date& time.
nPress "+/-"key to adjust digit-size.
nPress "OK" key to affirm and turn back to standby condition.
Ringing setteing
nPress“↑/↓”key -》choose the music you like (12 pieces in total)
nPress“+/-”key-》increase or decrease the volume level (7 levels in total)
nMute: long press"-"key still there is a mute symbol.
nPress "OK" key, confirm and back to standby condition
Lock Delay
nPress “↑”or “↓”key to adjust the time, the range of the time is 1~6 seconds.
nPress "OK" key, confirm and back to standby condition
Unlocking Explanation
Only in the state of intercom, press “ON/OFF Switch” to unlock with unlocking symbol
showing on the screen.
PIR : ON/OFF
nPress“↑”or “↓”to choose “ON” or “OFF”, the setting value shall be sent to outdoor
camera by pressing “OK” key

PIR Explanation
The PIR detects human being within its detection range, the signal shall be
sent to indoor monitor to wake up the screen and activate photo snapping.
After that, outdoor camera and indoor monitor would get into standby state.
When the screen is lit, press “OK” key to intercom
When the configuration is one camera and three indoor monitors, the PIR
function could be switched on or off through menu of each indoor monitor. A
red PIR symbol shall be shown on the top of the screen after switching on the
PIR function.
The other two indoor monitors shall show PIR state synchronously when
communicating with outdoor camera.
When someone is getting into the detection range of PIR, only one of the
indoor monitors would be woken up and takes photo.
After matching code, PIR would be switched off.
Call and Answer
In standby mode, press "doorbell key" to call, the background light of the outdoor unit
lights up with a sound of “Du Du”. The screen of handset shows image and the unit rings
for Max. 30 seconds. If there is no reply signal from handset, the outdoor unit stops the
Call and recall is allowed.
■Answer: press “OK” on indoor monitor -》ring stops and the unit turns into
intercom mode, intercom time is Max. 90seconds.
■Unlock the door : press the “ON/OFF”button briefly while the monitor is
displaying the camera’s view
■Exit: press “OK” key again-》the unit turns into standby mode with a sound of
“Beep”.
■Automatic photo shoot: if nobody answers the call in 5 seconds, indoor monitor
starts taking photos automatically.
Indoor unit View Outdoor unit
nPress the “ON/OFF”button to turn the monitor’s display ON.
nPress the monitor’s “ ” button to turn the camera on. At this time, the monitor
can hear sound and view video from the camera.
nPress the monitor’s “OK”button to talk with the visitor
nPhoto: in monitor mode -》press photo-taking of “FUNC” fuction key -》one
press one photo
nEnd1: in monitor mode -》press “ ” monitor key -》end monitor and turn back to
standby mode.
nEnd2: in intercom mode, press “OK” to hang off and turn back to standby mode.
Unlock the door
press the “ON/OFF”button briefly while the monitor is displaying the camera’s view
Take a photo
1. While the monitor is displaying the camera’s view, press the “FUNC”button to
manually take a photo.
2. If the user does not answer a call within 5 seconds, the camera will take a photo
automatically.
NOTE: If the monitor’s battery is low, the photo-taking function will not work.
Night-vision
With night-vision function, even under the environment of extremely poor visibility, the
outdoor unit can activate infrared lamps and recognize clearly objects or people within
the distance of 1.5meter (the best focus of this product is 0.8 meter). In addition, under
complete black condition, it displays black and white effects.
！Note: Please keep the lens of infrared lamps clean.

Exposure Adjustment
Exposure adjustment: under the environment of extremely poor visibility and the image
is not clear due to the brightness, however, the brightness is adjustable: 9 grades for
exposure adjustment.
■While the camera’s image is displayed -》press “↑or ↓” to adjust the grade of
expsure, every press adjusts one grade.
Photo Preview & Delete
nPress the “ON/OFF”button to turn the monitor’s display ON
nPreview: long press “↓/key", display the latest pictures which are ranked by
time, the latest one is on the top list.
nCheck: press "↑up"key,check previous photo-》press"↓down key", check the next
photo.
nDelete: press "Delete" of “FUNC”-》press "↑Up" or "↓Down" key to select
"yes"or "No"-》press "OK" to confirm.
nExit: finish the operation, press "OK" key to exit photo preview.
Match code setting
By default, the monitor is paired with the camera. These instructions apply to
pairing a second or third monitor.
nHandset is in shutdown mode-》long press power button-》"Welcome" would be
displaied on the screen-》please immediately click the power button-》screen would
be displayed "Pairing";
nMeanwhile, click "Reset" key of outdoor unit-》red lamp flashes and then match the
code.
nIf there is image on handset, code match succeeded; otherwise, match the code
again.
When pairing an extra unit you need to press the reset button on the outside unit twice,
only press during one second, not longer. Note that this procedure is different from
pairing the indoor unit from the XT-WG01.
Please follow the steps below for pairing extra indoor units:
1. press long on the outside unit reset button until the outside unit will sound a “di”
alarm and a blue LED light shines. Turn on the first indoor unit and press on the
power button several times (Quick press), if you see a picture on the monitor the
action you performed was successful.
2. press twice on the outside unit reset button (LED light shines and alarm sounds
continuously), now turn on the second indoor unit and press the power button
several times (Quick press) until you see a picture on the monitor.
Note: a outdoor unit could max. support 3 handsets. If you match the code forth
time, it would delete the previous three codes.
Battery and Charge
●Be sure the activity of the battery, please fully charged the new battery.
●When the outdoor unit is at low power, the lamp of launcher would flash. It remains
you to charge.
●The battery of outdoor launcher can be changed or charged by USB. The red light
keeps bright.
●When the Indoor monitor is at low power (≤a bar), the red indicator lamp will flash
every second, please charge immediately
●The Indoor monitor can be charged by the table type holder or by USB, green light
keeps bright.
●Charge-and-work supported. When the battery is charged fully, it auto stops
charging.
●Battery type: high-quality lithium battery, please use the BP-6M model battery if it
needs replacement
●Charging and battery attentions, please reference the chapter “Warms and attentions”
in this manual
Notice: Under the low power, display, photo-taking functions can’t work normally.

Configuration
Manual
1piece
Outdoor unit
1piece
Indoor monitor
1 pieces
Table type holder of handset
1piece
Charger with USB port
1pieces
Charger with DC plug
1pieces
DC jack with pigtail
1piece
USB cable
1pieces
Lithium battery (BP-6M)
2pieces
Screw
5pairs
Statement
This product maximum supports 1outdoor units to 3 Indoor monitor .The door phone has
finished code match and can be used directly.
If you need more pieces of indoor monitors or outdoor units, please contact your local
distributors .
General faults and solutions
Fault
Cause(s)
Solution(s)
Can not start up
Neglected to press switch button
Press switch button
Lithium battery is not installed
Install lithium battery
Low battery
Charge up lithium battery
No connection to power adapter
when battery runs out
Connect to power adapter
Can not charge
Adapter connector doesn’t
connect to charging port of
machine correctly
Reconnect correctly
Adapter doesn’t connect to
110V--240V alternating current
Plug into the socket to
connect to alternating
current
Outdoor unit
cannot call or
connect to
Indoor monitor
Code match failed
Clear code, and re-match
code
Image has noisy
point or flickers
Handset is placed near to TV
player, microwave oven,
daylight lamp or mobile phone
which produces electromagnetic
wave interference.
Keep handset far away
from the interference
items
No signal for
Indoor monitor
Outdoor unit doesn’t connect to
the power
Connect to the power
Distance between outdoor unit
and Indoor monitoris too far
Adjust to appropriate
distance
Disturbed by magnetic field
around
Keep handset far away
from magnetic field.

Pairing extra Indoor Units
When pairing an extra indoor unit you need to press the reset button on the outside
unit twice, only press during one second, not longer. Note that this procedure is
different from pairing the indoor unit from the XT-WG01.
Please follow the steps below for pairing extra indoor units:
1. press long on the outside unit reset button until the outside unit will sound a “di”
alarm and a blue LED light shines. Turn on the first indoor unit and press on the
power button several times (Quick press), if you see a picture on the monitor the
action you performed was successful.
2. press twice on the outside unit reset button (LED light shines and alarm sounds
continuously), now turn on the second indoor unit and press the power button several
times (Quick press) until you see a picture on the monitor.