Yaesu FC-40 User manual

NEW PRODUCT NEWS
FC-40
The FC-40 is a microprocessor-controlled antenna
impedance matching network designed to provide
all-amateur-band transmitting capability with the
FT-897/857 Series of transceivers, when used with
an end-fed random wire or long whip antenna.
The FC-40 makes use of the control circuitry built
into the transceiver, which allows the operator to
control and monitor automatic operation of the
FC-40, which mounts near the antenna feedpoint.
The FC-40 uses specially-selected, thermally-
stable components, and is housed in a waterproof
case to withstand severe environmental conditions
with high reliability.
A carefully-chosen combination of solid-state switching
components and high-speed relays allows the FC-
40 to match a wide variety of antennas to within a
2:1 SWR on any amateur band frequency (160
through 5 meters), typically in less than ten seconds.
Transmitter power required for matching may be
as little as 4 - 60 Watts, and matching settings are
automatically stored in memory for instant recall
when the same frequency range is selected later.
Automatic-Matching 100-Memory Antenna Tuner
Automatic Matching for FT-897/857 Series Transceivers
100 Match-Point Data Memories
WATER PROOF
WATER PROOF
9.4" x 7" x 2.1"
236 x 175 x 53 mm
COMPACT SIZE

FC-40
Operating Frequency Range : 1.8 - 54 MHz with 20+ m end-fed wire,
7 - 54 MHz with YA-007 HF 2.5 m Mobile Whip Antenna
Input Impedance: 50-Ohms
Maximum Power: 100 Watts
Matched SWR: 2.0:1 or less
(if antenna is not a multiple of 1/2 )
Tune-up Power: 4 W ~ 60 W
Tune-up Time: 10 seconds maximum
Impedance Matching Memories : 100 channels
Power supply: 13.8 V DC ±15% (supplied from transceiver)
Case Size (WHD): 9.4" x 7" x 2.1" (236 x 175 x 53 mm)
Weight: 2.6 lbs. (1.2 kg)
Automatic-Matching 100-Memory Antenna Tuner
2004.0505NA Printed in Japan
VERTEX STANDARD CO., LTD.
For the latest Yaesu news,visit us on the Internet:
4-8-8 Nakameguro, Meguro-ku, Tokyo 153-8644, Japan VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
http://www.vxstd.com
http://www.vxstdusa.com
Email: [email protected]
http://www.yaesu.co.uk
Email: [email protected]
Phone [phone]; Fax [phone]
http://www.vxstd.com.hk
Specifications
The FC-40 requires only two (supplied)
interconnections to your FT-897/857 Transceiver:
a coaxial RF cable and a data/control
cable. All
required power is supplied from the transceiver,
and then you just connect your antenna and
ground leads for instant operation on your
favorite band!
Rugged, low-loss components
are employed throughout
the FC-40, to ensure reliable
operation for many years in
a wide range of environmental
situations. The high-Q matching
network ensures the efficient
transfer of power to the
antenna radiating element,
with the convenience of
instant band change thanks
to the microprocessor control
circuitry.
ANT
FC-40
GND
Coaxial Cable (5 m)
Control Cable (5 m)
About this brochure: we have made this brochure as comprehensive and factual as possible. We reserve the right, however, to make changes at any time in equipment, optional accessories, specifications,
model numbers, and availability. Precise frequency range may be different in some countries. Some accessories shown herein may not be available in some countries. Some information may have been
updated since the time of printing; please check with your Authorized Yaesu Dealer for complete details.
FT-897D