V1.1
Package Contents
Quick Installation Guide
Resource CDEthernet Cable
Power AdapterIP Camera
1Hardware Introduction
Physical Description
Quick Installation Guide
Indoor Wireless HD IP Camera
Hardware Installation
Model: FC2501PA
Wi-Fi Antenna
Mounting Bracket
Power light
Network light
I/O Alarm
Antenna
Power
LAN
Speaker
IN OUT
I / O Alarm LAN
DC 5V
Audio Output
Audio Input
Audio
OUT / IN
Microphone
LENS
SD Card
Slot
Reset/WPS Button Mounting Port
Network Light Status
Network Light Description
Off No Wi-Fi connection
Flashing every 0.2 seconds EZLink takes effect (default)
Flashing every 0.4 seconds WPS is connecting
Slow Flash once per second Wi-Fi connected
Constant for 3 seconds Camera resetting
1. Screw the mount on the wall with the two screws
provided.
2. Loosen the thumb screws to adjust the mount to
the desired position. Once the position is set,
tighten the screws securely.
Quick Start Guide
Home View Pan,Tilt, Zoom
Camera (WIPC-303W)
Note: Waste electrical products and batteries should not be disposed
of with household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice.
The Home View Camera can be free standing
or fixed in place. To mount your Home View
Camera, please follow the steps below.
1. Screw the mount on the wall with the two
screws provided.
2. Loosen the thumb screws to adjust the
mount to the desired position. Once the
position is set, tighten the screws securely.
Before you continue, please note:
•Make sure your Smartphone is located near
the camera.
•Do not use an ethernet cable to connect
the camera if you want to use a wireless
connection.
•Make sure your Smartphone is connected to
your wireless router.
1. Fit Wi-Fi antenna to your Home View Pan,
Tilt, Zoom Camera and position upright.
2. Connect the AC power adapter to the
camera.
3. Ensure your wireless router is turned on and
connected to the internet.
Network Light Description
Constant Light Wired connection
Flashing every 0.2 seconds Wireless Connection (default)
Flashing every 0.4 seconds WPS is connecting
Slow Flash every 1.0 second Wi-Fi connected
2Add the IP Camera
You can add the IP Camera by smart phone.
1. Download the App
You can go to the App Store or Google Play store and
search for “My IPC Viewer”. Please download and
install it.
2. Add the IP Camera
Run the app, then you can tap the "+" button on the
app and follow the setup wizard to add your camera.
The App icon will be displayed after successful
installation:
My IPC Viewer
3Access the IP Camera
After your camera has been successfully added, you can
access the IP Camera via the app or browser.
If you want to use your camera via the browser, you can
search and access its local website in LAN.
1. Please copy the “Equipment Search Tool” file from the
CD to your computer.
Please Note:
Make sure the camera and PC are both in the same
Local Area Network (LAN).
2. Open "Equipment Search Tool".
3. Double click the camera list here, and your default
browser will open up to the login page.
4. When logging in for the first time, you will need to
download and install the add-on.
5. After logging in, you can manage camera through the
browser.
4FAQ
Forget Username / Password
Please Note:
After restore to factory default settings, you need to
config the Wi-Fi connection again, you can follow
the Setup Wizard of the App to add again.
In case your device failed to add by Wi-Fi, you can
use WPS connection. please refer to the User Manual
on the CD.
Restore camera back to factory settings:
1. Press "Reset" button for about 10 seconds with camera
powered on.
2. Release the button and wait about 30 seconds, the
camera will automatically restart, and restore factory
settings with its username / password recovery to
admin / (blank).
4 FAQ
2Add the IP Camera 3Access the IP Camera
You can add the IP Camera by smart phone.
1. Download the App
You can go to the App Store or Google Play store and
search for “My IPC Viewer”. Please download and
install it.
After your camera has been successfully added, you
can access the IP Camera via the app or browser.
2. Add the IP Camera
Run the app, then you can tap the "+" button on the
app and follow the setup wizard to add your camera.
The App icon will be displayed after successful
installation:
Shortcut icon for Windows OS
My IPC Viewer
Shortcut icon for Mac OS
Please Note:
If you want to use your camera via the browser, you can
search and access its local website in LAN.
Please copy the “IP Camera Search Tool” file from the
CD to your computer, run it to search and access the IP
Camera in LAN.
Forget Username / Password
Please Note:
After restore to factory default settings, you need to
config the Wi-Fi connection again, you can follow
the Setup Wizard of the App to add again.
In case your device failed to add by Wi-Fi, you can
use WPS or wired connection. please refer to the
User Manual on the CD.
Restore camera back to factory settings:
1. Press "Reset" button for about 10 seconds with camera
powered on.
2. Release the button and wait about 30 seconds, the
camera will automatically restart, and restore factory
settings with its username / password recovery to
admin / (blank).
Before you continue, please note:
Make sure your smart phone has connected to the
wireless router, and your smart phone and camera
in the same in LAN(Local Area Network).
Do not use an Ethernet cable to connect the camera
if you want to use a wireless connection.
1. Install Wi-Fi antenna and position upright.
2. Connect the power adapter to the camera.
3. Connect the wireless router to the Internet.
Hardware Connection
IN OUT
I / O Alarm LAN
DC 5V
4 FAQ
2Add the IP Camera 3Access the IP Camera
You can add the IP Camera by smart phone.
1. Download the App
You can go to the App Store or Google Play store and
search for “My IPC Viewer”. Please download and
install it.
After your camera has been successfully added, you
can access the IP Camera via the app or browser.
2. Add the IP Camera
Run the app, then you can tap the "+" button on the
app and follow the setup wizard to add your camera.
The App icon will be displayed after successful
installation:
Shortcut icon for Windows OS
My IPC Viewer
Shortcut icon for Mac OS
Please Note:
If you want to use your camera via the browser, you can
search and access its local website in LAN.
Please copy the “IP Camera Search Tool” file from the
CD to your computer, run it to search and access the IP
Camera in LAN.
Forget Username / Password
Please Note:
After restore to factory default settings, you need to
config the Wi-Fi connection again, you can follow
the Setup Wizard of the App to add again.
In case your device failed to add by Wi-Fi, you can
use WPS or wired connection. please refer to the
User Manual on the CD.
Restore camera back to factory settings:
1. Press "Reset" button for about 10 seconds with camera
powered on.
2. Release the button and wait about 30 seconds, the
camera will automatically restart, and restore factory
settings with its username / password recovery to
admin / (blank).
Before you continue, please note:
Make sure your smart phone has connected to the
wireless router, and your smart phone and camera
in the same in LAN(Local Area Network).
Do not use an Ethernet cable to connect the camera
if you want to use a wireless connection.
1. Install Wi-Fi antenna and position upright.
2. Connect the power adapter to the camera.
3. Connect the wireless router to the Internet.
Hardware Connection
IN OUT
I / O Alarm LAN
DC 5V
WPS
1. Go to the App Store or Google Play Store
and search for the Yale Home View App.
2. Download and Install the App.
3. To add the IP Camera, open the App and tap
the ‘+’ button on the App and follow the
setup wizard to add your camera.
Issue No. 1A
iOS
9+ Android
4.4+
Information and illustrations are subject to change.
Yale reserves the right to alter the specification and
product design at any time without notice.
Due to a continuous programme of improvement,
we reserve the right to discontinue support for older
iOS and Android operating systems.
Mounting Your
Home View Camera
Network Light Status
Hardware Connection
To View & Operate
Via Smartphone
