Yamatake VBC7000 Series User manual

1
CP-UM-1713E
VBC7000 Series
Seismic Detector
Installation Manual
Thank you for purchasing the VBC7000 Series
Seismic Detector.
This manual contains information for ensuring
the correct use of the VBC7000. It also provides
necessary information for installation, maintenance,
and troubleshooting.
This manual should be read by those who design and
maintain equipment that uses the VBC7000. Be sure
to keep this manual nearby for handy reference.
Please, read the ‘Terms and Conditions’ from the
following URL before order or use:
http://www.yamatake.com/products/bi/order.html
NOTICE
Be sure that the user receives this manual before the
product is used.
Copying or duplicating this manual in part or in whole
is forbidden. The information and specifications in the
manual are subject to change without notice.
Considerable effort has been made to ensure that this
manual is free from inaccuracies and omissions. If
you should find an error or omission, please contact
Yamatake Corporation.
In no event is Yamatake Corporation liable to anyone
for any indirect, special or consequential damages as a
result of using this product.
©2009 Yamatake Corporation ALL RIGHTS RESERVED
WARNING
Warnings are indicated when mishandling this
product might result in death or serious injury.
CAUTION
Cautions are indicated when mishandling this
product might result in minor injury to the user,
or only physical damage to the product.
WARNING
Before wiring the VBC7000, be sure to turn the power•
off. Failure to do so might cause electric shock.
CAUTION
Be sure to read the installation manual before using•
this device. Improper use could result in damage to the
device or equipment, and may cause bodily injury.
Do not install the device in places below. Faulty•
operation, fire, or explosion could result.
On a steep incline•
In a place that is normally subject to vibration, or that•
receives shock from an opening and shutting door,
etc.
Where the temperature or humidity is high•
Where there is water droplet spray or excessive•
dampness
In a place subject to magnetic fields•
Where there is dust or corrosive gas•
Where there is flammable or explosive gas•
Do not use this device as a step, or subject it to•
unreasonable force. Product damage or user injury
could result.
To avoid malfunction, never remove the cover.•
Make sure that the locking screw is fastened before•
transporting the device. Otherwise the sensor may be
damaged by vibration or impact.
Do a functional check at least once a year, and check•
the Gal response level at least once every three years.
1. Overview
The VBC7000 series seismic detector can be installed
in industrial or workplace environments to prevent
secondary damage in the event of an earthquake by
preventing the release of harmful gases, performing
emergency shutdown of equipment, activating an alarm,
etc.
Main Features
Depending on the intended use of the detector, fifteen•
models are available for accelerations from 12 to 250 Gal.
Faulty activation is minimized as the unit’s construction•
makes it difficult for it to be activated by non-earthquake
high frequency vibrations from sources like machinery or
dump trucks.
Functional checks can easily be performed after mounting•
or installation.
The operating status can be checked visually in the•
indication window, which changes from green to red
when the detector is activated.

2
Operating principle
Normally the internal sensor is attached to a permanent
magnet, as shown below. If an earthquake occurs and the
sensor is subjected to a force that exceeds the selected
horizontal acceleration, the sensor instantly drops and
presses a lever, which activates a micro switch.
Micro switch Micro switch
NC
NO
COM
NC
NO
COM
Permanent magnet
Lever Lever
Sensor
Permanent magnet
Sensor
Handling Precautions
If the locking screw is fastened, the sensor is
pushed up and is unable to drop. The locking
screw must be removed before use.
2. Part names
S
E
R
E
T
E
T
S
T
NC NO COM
0
20
10
VBC7000
Scale plate
Ground terminal
Cover
Level adjustment screws
Grommet with
membrane
Indication window
Spare screw
Locking screw
Level
adjustment nut
Setting knob
Base
Mounting holes
Side panel
Level
Terminals
Ball chain
3. Installation and wiring
CAUTION
To prevent electric shock, connect the wiring for the•
power last.
Check the wiring before turning the power on.•
Otherwise electric shock or damage to the device may
occur.
Mount the device on a firm wall or pillar. Otherwise a•
malfunction may occur.
Mount the device vertically, using the level, to prevent•
malfunction.
Never remove the cover. Doing so might cause a•
malfunction.
Installation
Hold a plumb line against the wall or pillar where the1.
detector is to be mounted and determine the position of
the mounting holes using this line as a datum.
Attach the detector firmly using four M6 screws in the2.
four mounting holes.
After loosening the two level adjustment screws and the3.
level adjustment nut, move the base back and forth and
around so that the ball chain is not in contact with the
perimeter of the level hole, and then fasten the screws
and nut temporarily. Adjust the base carefully so that the
ball chain is positioned in the center of the level hole,
and tighten the screws and nut securely.
Handling Precautions
If the ball chain is touching the perimeter of the
level hole, faulty operation may occur.
Adjust the scale plate so that the “0” is in line with the4.
pointer on the base, and fasten securely.
10
20
0
Ball chain
Center
Wiring
CAUTION
Do the wiring work in conformity with the electric•
facility technical standards.
The grommet membrane protects against dust. Cut it•
only where necessary for the wires to pass through.
Do not put wire around the setting knob.•
Connect the ground terminal to the earth. Otherwise if•
there is an insulation failure or the like, there will be an
electric shock hazard.
Normal position
Terminals
NC NO COM
Loosen the side panel retaining screw and remove the1.
side panel.
Pass insulated wires through the grommet membrane.2.
Connect the wires to the terminals.3.
After wiring, re-attach the side panel.4.
After installation and wiring, remove the locking screw5.
and replace it with the spare screw to protect against
dust. Keep the locking screw in case there is a need to
move the detector in the future.

3
4. Operation
Functional check and setting
SET: Gently rotate the setting knob to the RESET side
until it stops. The detector is now set and the
display window turns green.
TEST: Rotate the set dial to the TEST side to activate the
detector, and the display window turns red. Check
that the electrical contacts are operating correctly.
After testing by turning the knob between RESET and
TEST two or three times, turn it to RESET to begin
operation.
S
E
R
E
T
E
T
S
T
RESET
TEST
5. Maintenance
CAUTION
In conjunction with the periodic inspection of•
equipment or machinery, do a functional check at least
once a year, and a Gal response level check at least
once every three years.
Replace the detector if any abnormality is found in the•
functional or Gal checks.
Before transporting, be sure to fasten the locking•
screw. Otherwise vibration or shock may damage the
detector.
Gal response level check
Remove the side panel.1.
Loosen the level adjustment nut sufficiently so that the2.
base can be moved left and right, and remove the two
level adjustment screws.
Using the level adjustment nut as the axis of rotation,3.
gently rotate the base clockwise and note the pointer
indication on the scale when the device is activated.
Repeat this procedure two or three times, and check that
the average reading falls within the red region of the
scale.
Handling Precautions
In this procedure, slight variations in the reading
may occur according to the adjustment of the
level at the time of installation and the zero
adjustments for the scale plate, in addition to the
way in which the base is rotated.
After the inspection has been completed, return the4.
detector to its former state, and fasten securely.
10
20
0
10
20
0
Red region
6. Specifications
Item Specification
General
Name Seismic detector
Detection
method
Magnetic
External
dimensions
147×163×102.5 mm (W×H×D)
Mass Approx. 1.6 kg
Color Blue
Mounting Indoor, on firm wall or pillar surface (level
for vertical mounting is provided).
Retaining screws: M6 (4)
Mounting pitch: 130×130 mm
Terminal box M3.5 terminal screws
Conduit Dia. 15 mm, grommet with membrane
Allowable
temperature
-10 to +50 °C (no high humidity or
corrosive environments)
Performance
Sensing
direction
Horizontal and vertical
Operation
indication
By change of color in indication window:
green for Run (reset), red for Stop
(tripped out)
Setting Set manually with setting knob
Operation
check
Manual
Acceleration
setting check
Gal response level check by tilting the
detector
Electrical
Contact form SPDT (single pole double throw)
Contact rating 125/250 Vac, 10 A with resistive load, 2 A
with motor load (power factor 0.4)
Contact
material
Silver alloy
Insulation
resistance
100 MΩ or more (500 Vdc megger)
Dielectric
strength
1500 Vac, 1 min

4
External Dimensions
Unit: mm
VBC7000
0
20
10
147
113
130 ±1
80
23
102.5
82.5
38.5
163
130 ±1
36102
4-10
Operating characteristics
10
0
100
200
300
400
Non-earthquake vibrations:
The VBC7000 is not sensitive
to non-earthquake vibrations.
Operating range of VBC7000
Earthquake
area
Acceleration
(gal)
Setting acceleration (100 gal)
Frequency
(Hz)
VBC7000 series models
Unit: Gal
Model number Acceleration setting
VBC7000-012 12 ± 7
VBC7000-015 15 ± 10
VBC7000-020 20 ± 14
VBC7000-025 25 ± 15
VBC7000-030 30 ± 15
VBC7000-040 40 ± 16
VBC7000-060 60 ± 18
VBC7000-080 80 ± 20
VBC7000-100 100 ± 22
VBC7000-120 120 ± 24
VBC7000-135 135 ± 26
VBC7000-150 150 ± 27
VBC7000-200 200 ± 32
VBC7000-225 225 ± 35
VBC7000-250 250 ± 37
Advanced Automation Company
1-12-2 Kawana, Fujisawa
Kanagawa 251-8522 Japan
URL: http://www.azbil.com
Specifications are subject to change without notice. (08)
1st Edition: Issued in Feb. 2009 (S)