Yard Craft Elevated Garden Planter User manual

Natural Cedar
ELEVATED GARDEN PLANTER
Assembly Manual
GARDEN BED KIT CREATES UP TO
9 SQ. FT. OF GARDEN SPACE
47.5”
27.5”
32.875”
18”
Elevated Garden Planter
• 7.6 Cubic feet of soil to ll
• Creates 9 square feet of garden area
12.75”

Elevated Garden Planter Assembly Manual
2YardCra.com Info@YardCra.com 171 Jalyn Drive New Holland PA 17557 1-844-442-1615
Parts List
(4) 1x3 Post Boards (4) 1x4 Post Boards (2) Long Bottom Rail
Boards
(2) Short Bottom Rail
Boards
(4) Post Supports(2) Long Top Rail Boards (2) Short Top Rail Boards (8) Shelf Boards
(6) Long Side Boards (6) Short Side Boards (16) 2” Screws (45) 1” Screws
(16) ¾” Screws (8) 3” Screws (20) 1 ⅝” Screws

3
Elevated Garden Planter Assembly Manual
YardCra.com Info@YardCra.com 171 Jalyn Drive New Holland PA 17557 1-844-442-1615
Repeat steps 1 and 2, to create a total of four Post
Assemblies.
Lay the Long Bottom Rail Boards and the Short Bottom
Rail Boards down on a at surface. Align at the inside
corners. Fasten together at each corner with (2) 3”
Screws.
Set the Bottom Rail assembly from step 4 onto the post
supports.
Fasten the Post to the Bottom Rails at each corner with
(2) 2” Screws.
Step: 1 Step: 2
Step: 4
Step: 3
Step: 6
Step: 5
Place a Post Support between the two Post Boards.
Align with the end of the Post Boards and fasten
through pre-drilled holes with (4) ¾” Screws. Be sure
not to cover the holes in the Post Boards.
Align Here
Pre-drilled Holes
Fasten the 1x4 Post Board onto the 1x3 Post Board with
1 ⅝” Screws through pre-drilled holes. Make sure the
Post Boards are in the correct position. e two holes
need to be aligned as shown.
Align Here

Elevated Garden Planter Assembly Manual
4YardCra.com Info@YardCra.com 171 Jalyn Drive New Holland PA 17557 1-844-442-1615
Place the Long Side Boards into the notch in the Long
Bottom Rail with the groove down. Place the second and
third Long Side Board in place, interlocking onto the
previous Side Boards. Ensure Posts are level both ways.
Fasten to Post with 1” Screws through pre-drilled holes.
Keeping all the Posts level both ways, repeat step 9 to
install the opposite side Long Side Boards.
Keeping all the Posts level, using steps 9 and 10, install
the Short Side Boards.
Place the Short Top Rail on top of the Post with the Side
Boards going into the notch. Fasten to the Side Boards
with 2” Screws through pre-drilled holes.
Repeat step 12 to install the opposite end Short Top
Rail.
Using steps 12 and 13, install the two Long Top Rails.
Step: 7 Step: 8
Step: 9
Step: 12
Step: 11
Step: 10
Notice the
grooves in
the Side
Boards
(6) 1 ¼” Screws at each end
2” Screws

5
Elevated Garden Planter Assembly Manual
YardCra.com Info@YardCra.com 171 Jalyn Drive New Holland PA 17557 1-844-442-1615
Align the top of the Top Rails and fasten the Short Top
Rail to the Long Top Rail using 2” Screws through pre-
drilled holes. Repeat this step on the opposite end.
Carefully lay the assembly on it’s side.
Fasten all the Bottom Rails to the Side Boards with 2”
Screws through pre-drilled holes.
Set the assembly back to it’s upright position.
Lay the Shelf Boards along the bottom, on top of the
Bottom Rails. e Shelf Boards will not be fastened.
You’ve successfully assembled your Elevated Garden
Planter. You are now ready for soil.
Step: 13 Step: 14
Step: 15
Step: 17
Step: 16
Align here
2” Screws
Screw Locations