yellow jacket SuperEvac 9358 series User manual

Models 93511 - 93516
93540 - 93598
SuperEvac®
Vacuum Pump
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

shipping cap prior to use.
of motor.

Dual Voltage Motor Power Conversion (if applicable)
*Warranty is void if the set vacuum pump voltage does not match the power supply. Dual voltage
motors are factory set to 230V/50Hz.
8) Use a SuperEvac System I, II or
III to decrease
vacuum time by
over 50%. These
systems include
a 2-valve
vacuum mani-
fold and two
3/8” vacuum hoses which can
evacuate three times faster than a
1/4” hose.
9) Use a heat gun ot the condenser
and evaporator to speed the evacua-
tion process.
Built-in vacuum gauge: The unique
built-in indicator gauge in
you pump monitors
evacuation progress
down to the 29-30”
range. If the reading stays
in the mid range, there is
either high contamination
or a large leak in the system.
If you think there is excessive moisture,
blow out the AC&R system with dry
nitrogen wherever possible. This reduces
the amount of contaminants that must be
“pulled” into the pump and increases
evacuation speed.
Use a nitrogen regulator
valve with pressure
limited to 150 psi, and a
frangible disc device set
at 175 PSIG.
When the indicator
reaches the 29-30” range,
turn on the electronic micron gauge for
more precise readings.
Oil Changes: CHANGE OIL
AFTER EACH USAGE to protect
pump components from contaminants
pulled into pump during service. Place
used oil in a sealable container and
dispose properly in accordance with
local regulations.
STEP 1
Disconnect the
motor from the
power supply
and remove.
Remove the
yellow “CAU-
TION” sticker
from the back of
the motor.
STEP 2
Pull up on the white plastic “arrow”
switch using needle-nosed pliers until
the switch is
loose inside the
motor housing (it
will not come
completely out of
the motor).
Note: Do not try
to turn or rotate
the switch until it has been pulled up and
is loose.
STEP 3
Point the arrow toward the desired
voltage setting and push the switch back
down into the
motor. The arrow
on the switch
should be sub-flush
of the motor
housing when
correctly installed
at the desired
voltage.
HI = 230 VAC / 50 Hz
LO = 115 VAC / 60 Hz
STEP 4
Replace the yellow
“CAUTION” sticker
over the voltage
selector switch.
Ensure that the
voltage setting
corresponds with the power supply that
the motor is plugged into.

93504
93365
93514
93516
93594
9354x
93590
93592
93593
93595
93598
93511
9358x
93515
93596
9356x
93541 93561 93581 93591
(113 L/M) (311 L/M)(227 L/M)(170 L/M)

Pump #
93514
93516
93594
9354x
Pump #
93515
93596
9356x
Pump #
93511
9358x
Pump #
93590
93592
93593
93595
93598
4 CFM 6 CFM 8 CFM 11 CFM
(113 L/M) (170 L/M) (227 L/M) (311 L/M)
Mounting body
8. Complete body (individual parts below) 93500 93500 93517 93517
9. Shaft seal 93031 93031 93031 93031
10. 30” vacuum gauge 93011 93011 93011 93011
11. Vacuum gauge crystal 93012 93012 93012 93012
12. Gas ballast with “O”-ring 93368 93368 93368 93368
13. “O”-ring for gas ballast/drain plug 93398 93398 93398 93398
14. 1/4” elbow tting 93028 93028 93028 93028
15. Intake ttings 93377 (3/8”)
40265 (Acme)
93377 (3/8”)
40265 (Acme)
93393 (1/2”)
40265 (Acme)
93393 (1/2”)
40265 (Acme)
16. Intake cap (1/4”) 93394 93394 93394 93394
17. Flare caps 93399 (3/8”)
40284 (Acme)
93399 (3/8”)
40284 (Acme)
93395 (1/2”)
40284 (Acme)
93395 (1/2”)
40284 (Acme)
18. Blank-off valve with handle 93366 93366 93366 93366
19. Complete parts for blank-off handle 93367 93367 93367 93367
Motor
20a. 1/2 hp - 115V / 60 Hz
(includes items 21, 22, 23a below)
93505 93505 93505 93505
20b. Export models: 1/2 hp - dual voltage
115V / 60 Hz, 230V / 50 Hz
(includes items 21 and 22)
93513 93513 93513 93513
21. 8/32 x 7-1/4” motor bolts (4) 93099 93099 93099 93099
22. Rocker style switch 93117 93117 93117 93117
23a. 8’ long US cord 93115 93115 93115 93115
23b. 8’ long EU cord (detachable IEC-320) 95431 95431 95431 95431
23c. 8’ long UK cord (detachable IEC-320) 95432 95432 95432 95432
Final assembly parts
24. 8/32 x 5/8” socket head screws 93506 93506 93506 93506
25. Oil cover gasket 93507 93507 93507 93507
26. Drive coupling 93047 93047 93047 93047
27. Coupling spider 93050 93050 93050 93050
28. Right or left leg assembly with screws 93034 93034 93034 93034
Damaged supply cords must be replaced by special assemblies available from the manufacturer or its distributors.
9354x 9356x 9358x 9359x
28.3 lbs. (12.8 kg) 29.0 lbs. (13.1 kg) 30.3 lbs. (13.7 kg) 31.5 lbs. (14.3 kg)

Part #142993_K
2003-2017
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com