Yokis Md3300mrp User manual

DS1054-074B

MD3300MRP 5454801 Radio: Load manager POWER

The complete instruction booklets in French, Spanish, German,

Nederlands, Danish / Norwegian and the device conguration

booklets via the Yokis PRO App can be downloaded by scanning the

following QR-Code.

1. GENERAL DESCRIPTION

The MD3300MRP device is designed to control electrical loads so as to

prevent, in case of simultaneous switching on of several devices, an overload

that may cause the maximum electrical energy consumption allowed by the

supplier to be exceeded and consequently the mains power supply to be

disconnected. For proper operation of the device it is necessary to:

• assign one or more MTR2000ERP(X) or MTR2000MRP(X) radio receiver

relays to the MD3300MRP device (up to 7 relays directly connected or

more than 7 using the RADIO BUS);

•

make the assignment between the receiver modules and the device

channels (max 8 channels, each with a different priority: channel 1 = priority

1 = highest priority), so as to indicate to the MD3300MRP load manager

which receiver modules are to be piloted according to the priorities.

It is possible to assign more than one receiver module to each

channel in order to disconnect several loads at the same time. This

also allows simultaneous control of phase and neutral on the same

load, where this is deemed necessary.

If the absorbed power exceeds the set threshold continuously for the

pre-alarm time (Ton), the MD3300MRP load manager provides the loads

disconnection (receivers), starting from the lowest priority, as long as the

value of the absorbed power does not result lower than the activation

threshold. Once the alarm reset time (Toff) has elapsed, the device provides

the loads connection (receivers) in reverse order. The load manager and

the actuators communicate exclusively via radio.

RADIO RANGE

POWER Range:

• Inside 100 m² apartments with perpendicular crossing of main wall or

ceiling.

• 250m in open range.

Range may be reduced by presence of metallic elements, crossing of

walls or partitions.

2. INSTALLATION

Precautions for the installer

• The device must only be installed by qualied personnel in a closed

and adequately protected electrical panel, in accordance with national

installation standards.

• Before performing the installation operations, check that the devices

and conductors are not live.

• In order to comply with the safety regulations, the device must be connected

to an electrical line protected upstream by a magnetothermic switch (curve

C) with a current suitable for the load.

• Do not power on or connect the device if any part of it is damaged.

• After installation, inaccessibility to the connection terminals without

appropriate tools must be guaranted.

• The device can be used in environments with category of measurement

III and pollution degree 2.

For proper operation, the MD3300MRP load manager must measure the

same current as the general energy meter. For this reason the ideal position

for the device connection is immediately downstream of the general switch.

3. WIRING

RADIO: LOAD MANAGER

Wires with cross-section area of 0.5 mm2or larger must comply with

IEC 60332-1-2; wires with cross section area smaller than 0.5 mm2must

comply with IEC 60332-2-2.

It is necessary to wire and power the MTR2000ERP(X) or MTR2000MRP(X)

receiver before the assignment with the MD3300MRP load manager.

Always make sure that the MTR module is congured with the default

values.

The MTR used for load control must manage electrical sockets. In this case, in

rest conditions, the MD3300MRP load control device periodically carries out

an automatic check of all the MTR modules, in order to restart them in a time

that can vary between 5 minutes and 40 minutes “.

4. FIRMWARE RELEASE

Press and hold the keys and for more than 3 seconds to display the

rmware release of the device.

5. RESET TO FACTORY SETTINGS

If you want to delete all the settings made and restore the factory values, press

the keys and simultaneously for more than 3 seconds. The display will

show “RESET”. Factory values:

- Setpoint: 3.3 kW

- Ton: 60 seconds

- Toff: 120 seconds

CAUTION!: Resetting to the factory settings does not delete the radio

assignments made on the MD3300MRP device. To delete radio assignments,

see in detail chapter “REMOVING ALL RADIO ASSIGNMENTS”.

6. TECHNICAL SPECIFICATIONS

Power supply: 230V~ (+10% -15%) - 50 Hz

Maximum own consumption: 4 VA

Direct current connection until 32A

Settable power threshold range: 0.8 ÷ 7 kW

Pre-alarm time range Ton: 10 ÷ 9999 seconds

Disconnection time range Toff: 10 ÷ 9999 seconds

Blocks for cables with maximum section of 6 mm2

Radio frequency band: 2400 - 2480 MHz

Maximum radio power transmitted: 10mW

Operating temperature: -10°C ÷ +45°C

Operating humidity: 10% ÷ 90% non condensing

Storage temperature: -10°C ÷ +65°C

Container: 2 DIN modules

Overvoltage category: II

Operating altitude: below 2000 m (from 0 to 6560 ft)

Protection degree: IP20 / IP40 (on the front panel)

Indoor usage only, non-wet location

Insulation: reinforced between accessible parts (front panel) and all other terminals

Dimensions (H x L x D): 87,5 x 35,6 x 65 mm

7. KEY TO SYMBOLS

Symbol Description

Alternating input voltage

See the installation manual of the device

8. SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, FDI Matelec SA., declares that the radio equipment type:

MD3300MRP load manager (code 5454801) is in compliance with Directive

2014/53/EU. The full text of the EU declaration of conformity is available at the

following internet address: www.Yokis.com

RADIO ASSIGNMENT BETWEEN AN MTR RECEIVER MODULE AND THE

MD3300MRP LOAD MANAGER

For correct operation, it is essential to congure a radio assignment between

the MD3300MRP load manager and the MTR2000ERP(X) or MTR2000MRP(X)

radio receiver relays. The MD3300MRP device is able to manage up to 7

receiver modules directly connected. If you wish to manage more than 7

modules, it is necessary to create a radio bus to allow communication between

the MD3300MRP device and the subsequent modules.

Only one MD3300MRP device can be congured on each system.

▶On the MD3300MRP device, access the RADIO conguration menu by

simultaneously pressing keys and (for approx. 3 seconds) until the

display shows “bind.r1”.

You can cancel the assignment operation by pressing key.

▶Press key on the device to perform radio assignment.

▶While “InProG” is ashing (for 30 seconds), press briey with a sharp,

properly insulated tool into the “Connect” hole on the receiver module.

▶The MD3300MRP device will briey display the message “PASS” if the

assignment has been successful. The receiver module is now correctly

assigned to the MD3300MRP device.

▶If the device displays the message “Err. 03” the assignment has not been

successful. Repeat the operation and make sure to press into the “Connect”

hole on the receiver module within the 30 seconds in which the MD3300MRP

load manager displays the message “InProG”.

In some cases, if the receiver is out of radio range, it is possible that the

load manager is unable to communicate with the receiver and displays

the message “Err. 03”. In this case, refer to paragraph “Extending the

range”.

▶It is necessary to repeat the entire assignment procedure for each receiver

module you wish to assign directly to the MD3300MRP device.

REMOVING ONE SINGLE RADIO ASSIGNMENT

It is possible to remove an assignment between an MTR receiver module and

the MD3300MRP load manager.

▶On the MD3300MRP device, access the RADIO conguration menu by

simultaneously pressing keys and (for approx. 3 seconds) until the

display shows “bind.r1”.

▶Press the arrow key or until “dEL .r6” is displayed.

You can cancel the assignment operation by pressing key.

▶Press to remove the assignment.

▶While “InProG” is ashing (for 30 seconds), press briey with a sharp,

properly insulated tool into the “Connect” hole on the receiver module.

▶The MD3300MRP load manager will briey display the message “PASS” if

the receiver module assignment removal has been successful.

▶If the device displays the message “Err. 03” the assignment removal has

not been successful. Repeat the operation and make sure to press into the

“Connect” hole on the receiver module within the 30 seconds in which the

MD3300MRP load manager displays the message “InProG”.

>3s

Radio assignment

Removing a

radio assignment

Removing all

radio assignments

Procedure completed

Procedure failed

>4 sec.

Scan

DEVICE SCAN FOR YOKIS PRO APP

The scanning operation allows the MD3300MRP device to be detected by

the Yokis Pro App in order to subsequently carry out the assignment to the

channels and the parameter conguration (Paragraphs 10 and 11) directly

from the App.

▶On the MD3300MRP device, access the RADIO conguration menu by

simultaneously pressing keys and (for approx. 3 seconds) until the

display shows “bind.r1”.

▶Press the arrow key or until “SCAn” is displayed.

You can cancel the scan by pressing key.

▶Press the key to start the detection.

▶While “InProG” is ashing (for 30 seconds), start the device search on the

Yokis Pro App and select it.

▶The MD3300MRP load manager briey displays the message “PASS” if

the device has been detected and selected by the Yokis Pro App.

▶If the device displays the message “Err. 03” the detection has not been

successful. Repeat the operation and make sure to start the device search

on the Yokis Pro App within the 30 seconds in which the MD3300MRP

load manager displays the message “InProG”.

For more details on channel assignment and conguration of the

MD3300MRP device through the Yokis Pro App, scan the QR Code

at the beginning of the booklet to download the booklet.

REMOVING ALL RADIO ASSIGNMENTS

It is possible to remove all assignments between the various receiver

modules and the MD3300MRP load manager.

▶On the MD3300MRP load manager, access the RADIO communication

menu by simultaneously pressing keys and (for approx. 3 seconds)

until the display shows “bind.r1”.

▶Press the arrow key until “CLEAr” is displayed.

▶Press the key to delete all assignments.

▶The MD3300MRP device will briey display the message “PASS”. All

assignments with receiver modules have been removed.

EXTENDING THE RANGE

All YOKIS radio receivers also work as signal repeaters. The addition of one

or more modules allows extending the radio range by creating a Radio Bus

between the various modules on the system.

1) Creating the Radio Bus

▶Press once the Connect button of A module (the LED of A module starts

ashing), then press once the Connect button of B module (connection

between A and B is created and the 2 modules stop ashing).

▶The two buttons must be pressured within a maximum of 30 seconds.

▶Perform the same operation between B and C modules and so on with

the other modules.

Directive 2012/19/EU of the European Parliament and of the Council of 4 July 2012

on waste electrical and electronic equipment (WEEE)

The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that

this product must not be disposed of with your other household waste. Instead, it is your

responsibility to dispose of your waste equipment by handing it over to a designated collection

point for the recycling of waste electrical and electronic equipment. The separate collection and recycling

of your waste equipment at the time of disposal will help to conserve natural resources and ensure that

it is recycled in a manner that protects human health and the environment. For more information about

where you can drop off your waste equipment for recycling, please contact your local city ofce, your

household waste disposal service or the shop where you purchased the product.

9. RADIO CONFIGURATION MENU

Wiring via MTR2000ERP(X)

230V

50Hz

5454801 5454462

Two-pole

thermo-magnetic

circuit breaker

Wiring via MTR2000MRP(X)

230V

50Hz

5454801

5454464

Two-pole

thermo-magnetic

circuit breaker

>3 seconds