Young Display Y150PN User manual

Table of Contents
Items Pages
- COVER 1
- TableofContents 2
Chapter1 Introduction
1.1 Generalinformation 3
1.2 Features 3
1.3 Check thelist 3
Chapter2 Installing themonitor
2.1 Signalcableconnection 4
2.2 Power cordconnection 4
2.3 Audio cableconnection (Optional) 4
2.4 Power on 4
2.5 Selftestpattern 4
2.6 Adjustthepicture 5
2.7 Outofrange 5
Chapter3 Operation
3.1 Power ON/OFF switch 6
3.2 Power LEDindicator 6
3.3 OSDcontrolkeys 6
3.4 Instruction ofOSDmenu operating 6
Chapter4 TouchScreen
4.1 InstallingtheDriver Software(Windows XP,2000,VISTA, 7) 9
4.2 Calibration 11
4.3 Adjustsetting. 12
4.4 Removethesoftware. 14
Chapter5 TroubleShooting 15
Appendix A A TouchMonitorSafety16
Care and Handling ofYourTouchmonitor 16
Appendix B BNotationofLOTNumber 17
Howto contact us 17

C
Ch ha ap pt te er r 1 1
Introduction
1.1 Generalinformation
This monitoris ahigh-performanceintelligentmulti-scanningcolormonitor.Itis with 15"TFTLCD
screenand MCUdigitalcontrolwithoutradiation and glary. Theshapeis tinyand thin adaptingto small
places, saveyourmore place.
1.2 Features
-Thebestworkingmode:1024*768 @60Hz
-Viewingangle:H-120 /V-100
-Activearea :304.1*228.1mm
-Pixelpitch :0.297*.0297mm
-Brightness(Typ):250cd/m2
-Contrastratio :700:1
-Displaycolor:16.7M colors
-Thetypeoftouch panel:Surface AcousticWave(SAW)
-Thetypeofcontroller :RS232C&USBcombo controller
-In-Outterminals :15Pin D-sub, DVI, Stereo phonejack, USB2.0 &9Pin Serialjack, Power Jack.
1.3 Check thelist
Pleasemakesurethatall ofthefollowingitems areincluded before operatingthis monitor.
Ifanylisted items are missing, Pleasecontactyourdealerfortechnicalsupport.
-LCDmonitor(Includedbase) /ACadapter /Power cord /VGA 15Pin D-sub cable/USBcable/CDtitle
(Included usermanualand touch device driver)

C
Ch ha ap pt te er r 2 2
Installingthe monitor
Pleaseconsider thefollowingadvice before you install yourmonitor
Position :Chooseaplacethatreflects less to placeyourmonitor. Generally,there is asuitableanglewith
window.
Highness :Thepeak ofthemonitorshould bealittlelower thanyoureyeswhenyou sit down.
2.1 Signalcableconnection
Plugoneconnectorofthesignalcableinto theVGA orDVIportand lockthetwo bolts to ensure firm
grounding. Then plugtheother oneinto themonitorand lock thetwo bolts.
Pleaserefer thechapter5about"Installingthetouch screen"in caseoftheUSBorRS232Cconnection.
2.2 Power cordconnection
Plugonesideofpower cord into theACadapter and theother sideinto ACpower source outlet, then
plugtheoutputsideofACadapter into thepowerportatthesideofmonitor.
2.3 Audio cableconnection (Optional)
Plugthestereocablebetween themonitorand yourPC.
2.4 Power on
Switch on thepower to both themonitorand yourcomputer. Afterthemonitoris power on, theLED
lights up green orblue.IftheLEDbecomes red orflashing, pleasecheck thevideo signalcable
connection. IftheLEDisoff, pleasepower switchslightly.
2.5 Selftestpattern
Ifthere is no horizontalorverticalsync.signal,yourmonitorwill displayFig.1 to indicateno signalinput.
After afew seconds, themonitorwill comeinto waitingand savingpower mode;ifthemonitorreceives
thevideo signal, it will return to thenormalmode.
(Fig1)
NOSIGNAL

2.6 Adjustthepicture
In order to obtain thebestvisualdisplay,you needadjustit, pleaserefer tochapter 3 "TheOperation of
themonitor".
2.7 OUT OFRANGE
When thevideo signalexceeds thefrequencyrangeofthemonitor, themonitorMCUwill stop horizontal
and verticalscanninginorder to protectthemonitor. Fig.2 will bedisplayed on thescreen. Afterafew
seconds, themonitorwill enter turn-off mode. You mustrestartthecomputer and resetthefrequency
range.
(Fig2)
OUTOFRANGE

C
Ch ha ap pt te er r 3 3
Operation
OSD(On Screen Display)controlkeys (Fig.3)
(Fig3)
3.1 Power ON/OFF switch
This is aslighttouch digitalcontrolkey.Itis usedto turn themonitoron oroff
3.2 Power LEDindicator
When themonitoris working, thepower LEDisgreen orblue.Ifthemonitoris in savingpower mode,
thepower LEDwill bered offlashing.Ifyou turnoff thecomputer, thepower LEDwill beoff.
When theLEDis off, themonitoris off, butthepower adapter is on. In order to security,you should turn
off poweradapterwhileyou don'tusethemonitor.
3.3 OSDcontrolkeys
3.3.1 Power :Turn themonitoron oroff.
3.3.2 Menu :This keycan showthemenu and completetheconfirmation function.
3.3.3 AUTO:This keyis used to completeauto-adjustingfunction, it makethemonitorto bethebest
visualdisplaystatus in VGA mode.
3.3.4 / :Thesetwo keyswill completethenavigateup ordownand choosethecontrolofthe
menu function. Theadjustmentvaluecan besetby-/+key.
3.4 Instruction ofOSDmenu operating
3.4.1 Audio:press thekeyofMENUtoenter thenextlayersub-menu;adjustedcontentscontain Volume
and Mute
Volume
press thekeyofMENU toenter Volumesub-menu,
and thenpress (LEFT)/<->,(RIGHT)/<+> toadjust
thesizeofvolume
1024X768(60Hz)
Audio
Mute
press thekeyofMENU toenter Volumesub-menu,
and thenpress (LEFT)/<->,(RIGHT)/<+> tochoose
mute, namelyturn offaudio.
AUTOMENU POWER

3.4.2 Bright-Contrast
Brightness
Adjustthesizeofbrightness valuewith(LEFT)/<-
>, (RIGHT)/<+>
1024X768(60Hz)
Bright-Contrast
Contrast
Adjustthesizeofcontrastivevaluewith(LEFT)/<-
>, (RIGHT)/<+>
3.4.3 Color
ColorAuto
Press thekeyofMENU tochoose,adjustthe
balance oftricolor(Red Green Blue)
sRGB
sRGB
Press thekeyofMENUtochoose,maketheimage
colorconformtothefieldunification sRGB
standard
1024X768(60Hz)
Color
ColorTemperature
Press thekeyofMENUtochoose,enterthenext
layersub-menu, press (LEFT)/<->,(RIGHT)/<+>to
movebrightstrip, and choosesub-menu whatyou
want
3.4.4 Image:Press thekeyofMENU to enter, specificallyIncludes followingseveralitemofsub-menus
Auto
Press thekeyofMENU toenter choosingthisitem
ofmenu toautomaticallyadjustimageposition and
phasefromthemosttop IMAGE
Width
Press thekeyofMENUtoenter after choosing,
press (LEFT)/<->,(RIGHT)/<+>toadjustthesize
ofimagewidth
Phase
Press thekeyofMENUtoenter after choosing,
press (LEFT)/<->,(RIGHT)/<+>toadjust,inorder
to stabilizetheimageandremovethenoise
Horizontal
Press thekeyofMENUtoenter after choosing,
press (LEFT)/<->,(RIGHT)/<+>toadjustimage
horizontalposition whichdisplayon thescreen
1024X768(60Hz)
Image
Vertical
Press thekeyofMENUtoenter after choosing,
press (LEFT)/<->,(RIGHT)/<+>toadjustimage
verticalposition which displayon thescreen

3.4.5 Tools:PressthekeyofMENUtochooseand enterthenextlayersub-menu ofTOOLS,adjusted
contents contain:OSD Reset Sharpness DOStext/imagemode(640/720) Language
OSD
Entrance ofOSDmenu itselfofparameteradjusting,
press thekeyofMENU tochooseand enter thenext
layerdetailed sub-menu
- DisplayTimeofOSDmenu
- Horizontalposition ofOSDmenu
- Verticalposition ofOSDmenu
Reset
Press thekeyofMENUtoenter afterchoosing
under theOSDmenu, makethemonitorrestore to
thefactorystartingvalue,it isconvenienttouse
becauseofdisoperation orbeunabletoadjustinitial
value
Sharpness
Press thekeyofMENU under theTOOLSmenu to
chooseSharpness sub-menu, and thenpress
(LEFT)/<->,(RIGHT)/<+> to adjustsharpness
1024X768(60Hz)
Tools
Language
Press thekeyofMENU under theTOOLSmenu to
chooseLanguagesub-menu, andthenpress
(LEFT)/<->,(RIGHT)/<+> tochooseChineseor
English, press MENUto exit after affirmingagain
3.4.6 Input:Press thekeyofMENU tochooseand enter thenextlayersub-menu ofINPUT,adjusted
contents contain :VGA DVI
VGA
press thekeyofMENU to chooseVGAinputmode.
1024X768(60Hz)
Input
DVI
press thekeyofMENU to chooseVGAinputmode.

C
Ch ha ap pt te er r 4 4
TouchScreen
YoungDisplayprovidesdriver software thatallowsyourtouch monitorto work withyourcomputer. Drivers
are located on theenclosed CD-ROM forthefollowingoperatingsystems:
Windows 98/Me/XP/2000/NT/VISTA
Linux/DOS
4.1 InstallingtheDriver Software(Windows XP,2000,VISTA, 7)
4.1.1 Doubleclick thefileof “Setup.exe”in thefolder ,
4.1.2 TheWindowswill flipDialogBoxasfollow.You canchoosetheportasRS232CorUSB asyour
needs. Ifyou wantto usetheRS232C, startto install this driver afterplugtheportbetweenmonitor
toyourPC.Choose “KeeTouch, RS232 Series, Serial”and openand chooseyourCOMportas
follow.

.
4.1.3 Ifyou wanttouseaUSBport,starttoinstall thisdriver after unplugtheUSBcablebetween
monitorand yourPC. Choose “KeeTouch, USBSeries, USB”as follow.
4.1.4 Click theInstall button to startinstallingthedriver as following

4.1.5 Installation successfullyas following:
4.2 Calibration
4.2.1 Click attherightsideinthedowncorner oftheDesk-Top, thenchoose “Calibrate”inthepop-
outofthemenu as follow
4.2.2 Windowswill pop-outthecalibration interface,thenclickthereddotwithfinger onebyone,as
follow:

4.2.3 Afterclickingthered dots on byone, thecalibration is completed.
4.3 Adjustsetting.
4.3.1 Click attherightsideinthedown corner oftheDesk-Top, thenchoose “Adjustsettings”inthe
pop-outofthemenu as follow
4.3.2 Hardware :HandlingWholedesktop, Connected toyourport
4.3.3 Click Mode:Clickand drag, Systemmousesettings

4.3.4 Properties
4.3.5 Calibration
4.3.6 Status

4.4 Removethesoftware.
4.4.1 Open thecontrolpanelofyourPC and run themenu of “Add RemovePrograms”as follow:
4.4.2 Choosethe “UniversalPointDevice Driver”and click the “Change/Remove”,as follow:
4.4.3 You’rereadyto uninstall thedevice drivernow, click the “Uninstall”, as follow:

C
Ch ha ap pt te er r 5 5
TROUBLESHOOTING
Ifyou areexperiencingtroublewithyourtouch monitor, referto thefollowingtable.Iftheproblempersists,
pleasecontactyourlocaldealer orourservice center.
SolutionstoCommonProblems
Problem Suggestion(s)
Themonitordoes notrespond
after you turn on thesystem
1)Check thatthemonitor’s Power Switch is on.
2)Turn off thepower andcheck themonitor’s power cord
and signalcableforproper connection.
Characters on thescreenare dim Refer to theAboutTouch monitorAdjustments section
to adjustthebrightness.
Thescreen is blank 1)Duringoperation, themonitorscreen may
automaticallyturn off asaresult ofthePowerSaving
feature. Press anykeyto see ifthescreenreappears.
2)Refer to theAboutTouch monitorAdjustments
section to adjustthebrightness.
Screen flashes when initialized Turn themonitoroff thenturn it on again.
“OutofRange”display Check to see iftheresolution ofyourcomputer ishigher
than thatoftheLCDdisplay. Reconfigure theresolution
ofyourcomputer to makeit less than orequalto
1024X768 60Hz.
Touch doesn’twork Makesure thetouch cableis securelyattachedatboth
ends.

Appendix
TOUCHMONITORSAFETY
This manualcontains information thatis importantforthepropersetup andmaintenance ofyourtouch
monitor. Beforesettingup and poweringon yournewtouch monitor, readthrough this manual, especially
Chapter 2 (Installation),and Chapter 3 (Operation).
1To reducetherisk ofelectricshock, followall safetynotices and neveropen thetouch monitorcase.
2Turn off theproductbefore cleaning.
3Thesocket-outletshall beinstalled near theequipmentand shall beeasilyaccessible.
4Theslots located on thesides and top ofthetouch monitorcaseare forventilation. Do notblock or
insertanythinginsidetheventilation slots.
5Itis importantthatyourtouch monitorremainsdry.Do notpourliquid into orontoyourtouch monitor.
Ifyourtouch monitorbecomes wetdo notattemptto repairit yourself.
Care and Handlingof Your Touchmonitor
Thefollowingtips will help keepyourtouch monitorfunctioningattheoptimallevel.
To avoid risk ofelectricshock, do notdisassemblethebrick supplyordisplayunit cabinet. Theunit is not
user serviceable. Remember to unplugthedisplayunit fromthepower outletbefore cleaning.
Do notusealcohol(methyl, ethylorisopropyl)oranystrongdissolvent. Do notusethinner orbenzene,
abrasivecleaners orcompressed air.
To clean thedisplayunitcabinet, useacloth lightlydampened with amild detergent.
Avoid gettingliquids insideyourtouch monitor. Ifliquid does getinside, haveaqualified service
technician check it beforeyou power it on again.
Do notwipethescreenwith acloth orspongethatcould scratch thesurface.
To clean thetouch screen, usewindoworglass cleaner. Putthecleaner on theragand wipethetouch
screen. Neverapplythecleaner directlyon thetouch screen.

Appendix
Notationof LOTNumber
(XXXXXXXX-PPPMMDDYY)
XXXXXXXX :Productnumber.
PPP:Serialnumber “001”……..”999”
MM :Themonth ofproduct
DD :Thedayofproduct
YY:Theyear ofproduct
CAUTION
Don’tremovethelabelon rear sideofthis monitor.
It’s needed amaintenancein thefuture.
Howto contactus
CheckoutYOUNGDISPLAY sWeb site!! http://www.lcd21.co.kr
Get thelatest...
Product information
Specifications
Newson upcomingevents
Press releases
Softwaredrivers
ADRESS
404Ho, Byucksan-Technopia,434-6, Sangdaewon-Dong,Jungwon-Gu, Seongnam-si,Gyunggi-Do,
Korea.(462-807)
TEL:[phone] /FAX :[phone]
Website: www.lcd21.co.kr
Sales and technicalsupport: [e-mail]