YUANLEY 6 Port 10/100Mbps PoE Switch User manual

Chapter 4: Methods of installation and precautions
1.Packing List
2.The schematic of device connection
+
+
+
+
Open the packing box carefully, confirm the items should be as follows:
1). 1pcs PoE switch
2). 1pcs AC power cable
3). 1pcs user manual
4). 2pcs hangers, screws with nuts (4pcs screw on 4/8 port PoE switch, 6pcs on 16 ports )
5). 4pcs Mats
PS: Please contact the local dealer timely if you find the accessories missed or damaged.
Smart home
AP
Non PoE Camera
PoE Camera
PoE Splitter
Router
NVR
PoE Splitter
Pow er
SV
Smart PoE Switch
8PoE+3G 100/1000Mpbs
10

5.Installation platform:
No matter it is installed in the rack or other horizontal workbench, please pay attention to the below:
Confirm the rack or workbench with good stability;
Confirm the good cooling system of the rack, or keep the good ventilation indoor;
Confirm the rack with good grounding, keep the distance between the switch and
power outlet less than 1.5 meter.
4.Demand for Lightning Protection
It will cause the fatal damage to the electronic device by the split-second powerful current when the
lightning occurs. To achieve the better effect of lightning protection, please pay attention to the below:
Confirm the rack with good grounding;
Confirm the power outlet with good grounding;
Reasonable wiring to avoid lightning internal induction;
Recommend usage of signal lightning arrester when wiring outdoor
4.Installation for Products
1
2
3
1). Instruction for front hangers
Please use the front hangers to fix the switch when install the switch to the cabinet or above the cabinet.
The appearance of the front hangers are as shown in illustration 2-1
Illustration 2-1
Screw holes for hangers and cabinets
Screw holes for hangers and cabinets
Matched screws (to fix the hangers to the switch)
3). Install the switch to the cabinet
Please guarantee there are about 50mm space between the cabinets for the device
to radiate when installing the switch to the cabinet. Please use the standard hangers
to install the switch to the cabinet, the process is as follows.
Step 1: Take out the screws (matched hangers), install the hangers to the switch, as shown
in illustration 3-1
!
Illustration 2-2
2). Introduction for Mats
A set contains 4pcs mats, as shown in illustration 2-2. Please install 4pcs mats to the bottom of
the switch before install the switch on the platform.
Mats
Illustration 3-1
12

1
2
3
Step 2: Planning the position of the switch installation in the cabinet and install the floating nuts to
the settled position of the front hole of the cabinet
Holes for the front cabinets
Front panel of switch
Front hangers
Power
SV
5.Connection of the hardware
1).Connect one end of the cable to the switch and the other end to the corresponding device,
as shown as illustration 5-1
5.1.Connect to the RJ45 Port
RJ45Port
RegisteredJack
Illustration 5-1
PoE IP camera for security
Please confirm that the device is equipped with the PoE if the switch is passive; at the same
time, please confirm the voltage of the access device is matched with the switch’s, otherwise
it will burn the access device.
!
Step 3: One installer holds the bottom of the switch by hands and move the switch to the settled
position; another installer fixes the hangers to the front hole of the cabinet by floating nuts with
the screws.
2).Please check the condition of the corresponding indicator when electrified. It means the
connection works well when the indicator is ON; blocked when it is OFF, please check the wiring
and confirm the corresponding device start up.
8PoE+3G 100/1000Mpbs
13

SV