Zamel EXTA ZCM-31 User manual

ASTRONOMICAL ONE-CHANNEL
TIME PROGRAMMER ZCM-31, ZCM-31P/U INSTRUCTION MANUAL
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamel.com, e-mail: [email protected]
plik: zcm-31_31_pu_bateria_inst_ext_gb | modykacja: 25.10.2019
DESCRIPTION
MAIN MENU
APPEARANCE**
CHANGE OF MODE OF WORK (AUTOMATIC, MANUAL)
STORAGE MODE / BATTERY REPLACEMENT
● ZCM series programmers have a default setting, the so called storage mode in order to protect the battery during storage.
● In case of battery backup operation the storage mode is switched off during the rst use of the programmer. It is done by means of a short pressing of the
push-button and subsequent date and time adjustment.
● In case of a nominal power supply the storage mode is switched off during the rst use of the programmer by means of date and time adjustment.
● Adjusting the programmer into the storage mode is realised by means of a reset - in order to carry it out press at the same time the and push-buttons
in the main window.
● ZCM series programmers have the option to replace the clock maintenance battery. Before replacing the battery, disconnect the programmer from the
external power supply. Please pay the attention to correct battery polarity when replacing.
Do not dispose of this device with other
waste! In order to avoid harmful effects
on the environment and human health,
the used device should be stored in
designated areas. For this purpose, you
can dispose of household waste free of
charge and in any quantity to a collection
point set up, as well as to the shop when
you buy new equipment.
Description of elements and messages displayed
Buttons descriptions
• In the main window - entry to automatic mode or change of the transmitter status, if the clock is already in the automatic mode;
• In other windows - one level up exit without saving the introduced data;
• In the main window - entry to manual mode or change of transmitter status if the clock is already in the manual mode;
• In other windows- one level up exit without saving the introduced data;
• In the main window - entry to main menu;
• In other windows - entry to sub- menu or conrmation of the parameter being set;
• Shifting windows /menu options or increasing/ decreasing of the parameter being set;
• Right cursor () in the main window- displaying a time of sunrise and sunset.
We enter menu from the main window by
choosing OK; we move inside menu using cur-
sors . Return to the main window is possible
after pressing button or .
You can enter the windows of displaying cal-
culated sunrise/sunset time from the main
window by using cursor . Return is automat-
ical after 10 s.
Function Description
NIGHT BREAK SETTING
CORRECTION OF TIME SETTING (SUNRISE/ SUNSET TIME)
CURRENT TIME SETTING
CURRENT DATE SETTING
TIME SETTING (SUMMER/WINTER SEASON)
GEOGRAPHICAL POSITION AND TIME ZONE SETTING
EXTERNAL INPUT SETTING
EXTERNAL MEMORY ADJUSTMENT**
CALCULATED SUNRISE TIME
CALCULATED SUNSET TIME
FEATURES
TECHNICAL DATADESCRIPTION
ZCM-31
Power supply clamps: A1, A2
Rated voltage: ZCM-31: 230 V AC~(-15 ÷ +10 %)
ZCM-31/U: 24 ÷ 250 VAC, 30 ÷ 300 V DC
Rated frequency: 50 / 60 Hz
Rated power consumption: 2 W / 14 VA
Number of channels: 1
Programme: astronomical
Mode of work: manual, automatic
Change of season summer/ winter: automatic, manual
Colour of LCD panel lighting: amber
Input: yes
Accuracy of time measurement: max. ±1 s / 24 h at temp. 25 °C
Time of clock maintenance: 3 years
Time of programme maintenance: 5 years
Clamps of release system: IN, IN, IN, IN
Clamps of receiver power supply: 11, 12, 14
Parameters of transmitter contacts: 1NO/NC-16 A/250 V AC1 4000 VA
Number of terminating clamps: 12
Intersection of terminating conductors: 0,2 ÷ 2,50 mm2
Temperature of work: -20 ÷ +60 oC
Position of work: any
Fixing of casing: TH 35 rail (PN-EN 60715)
Level of protection of casing: IP20 (PN-EN 60529)
Protectivity class: II
Overvoltage category: II
Level of pollution: 2
Measurements: two-module (35 mm) 90x35x66 mm
Weight: 0,17 kg
Compatibility with norms: PN-EN 60730-1; PN-EN 60730-2-7
PN-EN 61000-4-2,3,4,5,6,11
● Steering dependant on a current hour in
an astronomical cycle,
● two-module casing with a protective flap
valve,
● steering input IN,
● lighting the LCD display.
Digital steering clocks ZCM-31 are intended
for realization of time functions in the sys-
tems of automatics and steering. Switching
on/off the appliance is connected with sun-
rise and sunset (dawn an dusk). The infor-
mation about geographic coordinates, the
place of the clock’s installation, current date
and a shift in relation to the universal time-
all these factors are used in order to cal-
culate the time of sunrise and sunset. The
system calculates the end of civil dusk, that
is the phase, during which the centre of the
Sun’s face is located on the 6 degrees angu-
lar below the horizon- the Sun’s face is not
noticeable but sky is lit with dispersed sun-
light. The system additionally has a function
of a programmed night break and an ability
of shifting the calculated time of sunrise and
sunset within a range of +/- 120 min. The
construction of a casing makes it possible to
install the system on a rail TH 35 and pos-
sible sealing the appliance with lead. The
construction of the system guarantees
supporting of all the settings with battery
energy when the electric power supply is
off.
In order to protect the battery during stor-
age, the ZCM series programmers have
a default setting, the so-called storage
mode in which the battery power con-
sumption is limited to a minimum.
The device should be connected
to a singlephase system accord-
ing to current standards. The
device connections will be de-
scribed in this manual. Only qual-
ied electricians are allowed to mount, connect
and adjust the device. It is necessary to read
this manual and know the unit functions be-
fore the device mounting. Do not disassembly
the device casing or you will lose any warranty
rights and expose yourself to the electric shock
hazard. Before mounting operation make sure
of disconnecting the connection wires from the
electric network. Use a cross-head screwdriver
of 3.5 mm diameter to mount the device. The
relay should be carried, stored and used in an
appropriate way. Do not mount the device in
case of any device parts lack, damage or defor-
mation. In case of malfunction please notify the
manufacturer.
CAUTION
* does not apply to the product ZCM-31
** apply to the product ZCM-31P/U
* does not apply to the product ZCM-31
** apply to the product ZCM-31P/U
**
- days of week
- relay status
- automatic mode
- manual mode
/ - winter time / summer time
- external input
/ - day / night
- day
- year
- night break setting
- time correction setting
- current time setting and summer/winter time shift
- current date setting
- geographical position setting
- external input setting
- external memory operation**
- external memory record**
- external memory reading**
- external memory busy**
- reading / record error**
/ - sunrise time / sunset time
/ - latitude/ longitude
- automatic, - user’s
- switched on / switched off
CHANGE OF MODE INTO MANUAL - if the system is situated in the main window and it is in the
automatic mode, pressing the button will cause a shift of the system from the manual mode with
simultaneous change of transmitter status;
Subsequent pressing of button will cause switching transmitter to the opposite status without
change of work mode;
CHANGE OF MODE INTO AUTOMATIC - if the system is placed in the main menu and it is in the
manual mode, pressing button will cause automatic shift to the automatic mode, with simultaneous
updating transmitter status.
Winter time
Summer time
Manual mode
Automatic mode
Week’s day
Relay state
Info eld / data
Current time
(gg:mm:ss)
Power terminals
(A1, A2)
LCD display
External memory**
Replaceable battery
Control buttons
Relay output terminals
(12, 12, 11, 11, 14, 14)
Trigger terminals
(IN, IN, IN, IN)
Day/night time

TIME CORRECTION SETTING
EXTERNAL MEMORY OPERATION**
GEOGRAPHICAL POSITION SETTING
NIGHT BREAK SETTING
TIME SETTING
WINTER / SUMMER TIME SETTING
EXTERNAL INPUT SETTING
DATE SETTING
- setting longitude, latitude and a time zone; entry to
reviewing and edition of settings after pressing OK, choose
parameters which should be changed with cursors re-
member at the same time that:
- latitude;
- longitude;
- time zone in relation to UTC time;
For window (latitude); press OK, so as to move to edition:
Choose latitude parameters (degrees) with cursors (within
range 90 South ÷ 90 North); conrm with OK;
Choose latitude minutes with cursors (if in the step 90
latitude was chosen, this step is omitted).
For window (longitude); press OK, in order to move to edition:
Choose longitude degrees with cursors (within range 180
West ÷ 180 East); conrm the choice with OK.
Choose longitude minutes with cursors (if in the step
longitude was chosen, this step is omitted).
For window (time zone); press OK, so as to move to edition:
Choose hour shift of time zone with cursors (within a
range -12 ÷ 12); conrm your choice with OK.
- setting the time correction; entry to review of settings after pressing OK;
Choose time which you should change with cursors , remember at the same time that:
Correction of dusk time; press OK, in order to move to edition;
Correction of dawn time; press OK, in order to move to edition;
Correct the time within a range of -120 ÷ 120 min., choose an adequate parameter
with cursors , conrm the choice with OK.
It is possible to exit every sub- menu window in any moment without saving set-
tings by pressing the button or .
- setting the duration time of a night break; entry to reviewing the settings after
pressing OK; Choose time which you should change with cursors , remember at the
same time that:
Time of commencement of a night break; press OK in order to move to edition;
Time of ending of a night break; press OK in order to move to edition;
Choose adequate hour with cursors , conrm the choice with OK;
Choose adequate minute with cursors , conrm the choice with OK;
ATTENTION!!!
The clock will work without a night break, if the times of night break beginning and
ending are the same.
It is possible to exit every sub- menu window in any moment without saving set-
tings by pressing the button or .
- setting the current clock time; entry after pressing OK;
HOUR- choose adequate hour with cursor which you can set
in 1-24 or 1-12 (AM) and 1-12 (PM)format; conrm with OK;
MINUTES - choose adequate parameter of minutes with cursors
conrm with OK;
Conrmation of the parameter of minutes causes simultaneous
nullication of the parameter of seconds and movement to the
window of time setting.
- choice of one of the two modes in which switching between winter and summer season time will occur. - switching will take place in an
automatic way, on the last Sunday of March, at 2.00 (for summer time) and on the last Sunday of October, at 3.00 (for winter time), - a user chooses
between winter/ summer time, entry after pressing OK;
setting the mode - choose mode or with cursors , conrm with OK; after choosing the mode , the clock automatically sets the time as
winter or summer one, depending on the arranged date; after choosing the mode you go to another window;
Choose time for winter/ summer one with cursors where is winter time and is summer time, if change of marker has happened the system will
change the current time by adding or subtracting 1 hour, conrm the operation with OK;
After choosing the system moves to winter/ summer time shift window.
- setting the mode in which the
system should operate after releasing
the external input IN; entry to edition after
pressing OK, choose adequate mode for
external input with cursors , remember
at the same time that:
- the function of external input is
switched off;
- manual mode with permanent
switching the transmitter off;
- manual mode with permanent
switching the transmitter on;
- automatic mode, the system switches
the transmitter on/ off according to the ar-
ranged programmes;
Conrm with OK the choice of a given
mode; conrmation will cause a moement
to the settings window of the external in-
put.
External memory allows for an easy record /
reading of the adjusted programs into the ex-
ternal memory, so they can be easily copied
to other programmers. It is very convenient in
case if we want to program more ZCM pro-
grammers or archive the adjusted programs.
– sub menu to the external memory
operation
– programs recording
– programs reading from the external
memory and storage in the programmer’s
memory
– the state of memory „busy” during a
record / reading
– correct record / reading
– record /reading error
It is possible to exit every sub- menu window in any moment without saving settings by pressing the button or .
- Current date setting; entry after pressing OK;
YEAR - choose adequate year with cursors conrm with OK, range of years: 2000÷2099;
MONTH - choose month with cursors conrm with OK;
DAY - choose day with cursors conrm with OK; the system has a protection against introducing incorrect parameter of a day for a given month ( it takes
into account leap years and it automatically calculates the day of the week on the basis of an arranged date);
Conrmation causes movement to a date setting window and set-up of current summer/ winter time - if the option is arranged.
It is possible to exit every sub- menu win-
dow in any moment without saving set-
tings by pressing the button or .
It is possible to
exit every sub-
menu window
in any moment
without saving
settings by
pressing the
button or .
It is possible to exit every sub- menu
window in any moment without saving
settings by pressing the button or .
* does not apply to the product ZCM-31
** apply to the product ZCM-31P/U
* does not apply to the product ZCM-31
** apply to the product ZCM-31P/U

MAIN RESET
GEOGRAPHICAL POSITION OF GREATER TOWNS AND CITIES IN EUROPE
* does not apply to the product ZCM-31
** apply to the product ZCM-31P/U
CONNECTIONMOUNTING
ADVANTAGES
Intelligent calendar - the system has an in-built calendar, which automatically takes into account
leap years, it makes introducing non-existent date impossible, and also calculates a day of a week
on the grounds of a date and it takes into account the change of time into winter/ summer one.
Universal external input - the system has an external input, with the help of which a user can
enforce change of clock work mode without the necessity of interfering in a switchboard but using
e. g. remote controller button.
Cooperation with the external memory** - the user has a possibility of a quick record / reading
of the adjusted programs into the external memory in order to copy them in other programmers
quickly.
DIMENSIONS
PRODUCT FAMILY
ZCM-31 Programmer belongs to ZCM
family of products.
1. Disconnect power supply circuit with
a fuse, electrical energy redundant
switch or insulation switch (all of
them connected to adequate circuit)
2. Check non- voltage status on
power supply conductors, with an
appropriate tool
3. Assemble the appliance ZCM in the
switching station on the TH 35 rail.
4. Connect conductors under clamps
according to the connection scheme
INNER DIAGRAM
RELAY CAPACITY
A2
A1
IN
μC
KLAW. LCD
RTC
ZAS.
In order to cancel the clock system (time,
date, activity of given functions etc.) you
should hold buttons ( and ) simultaneously
in the main menu for 3 sec;
All the display elds will light up;
After a while, the clock will automatically set
date and time.
Attention: In order to restore factory settings, you should additionally hold button OK
Amsterdam 52° 21’ N 4° 52’ E
Andorra 42° 03’ N 1° 31’ E
Athens 38° 02’ N 23° 44’ E
Belgrade 44° 49’ N 20° 28’ E
Berlin 52° 31’ N 13° 02’ E
Bern 46° 57’ N 7° 26’ E
Bratislava 48° 09’ N 17° 07’ E
Brussels 50° 51’ N 4° 21’ E
Budapest 47° 26’ N 19° 15’ E
Bucharest 44° 23’ N 26° 01’ E
Dublin 53° 26’ N 6° 15’E
Helsinki 60° 01’ N 24° 53’ E
Kiev 50° 28’ N 30° 29’ E
Chisinau 47° 00’ N 28° 05’ E
Copenhagen 55° 43’ N 12° 34’ E
Lisbon 38° 42’ N 9° 05’ E
London 51° 03’ N 0° 01’ E
Ljubljana 46° 03’ N 14° 31’ E
Luxembourg 49° 37’ N 6° 08’ E
Madrid 40° 26’ N 3° 42’ E
Minsk 53° 51’ N 27° 03’ E
Monaco 43° 04’ N 7° 25’ E
Moscow 55° 45’ N 37° 37’ E
Oslo 59° 56’ N 10° 41’ E
Paris 48° 51’ N 2° 02’ E
Podgorica 42° 25’ N 19° 02’ E
Prague 50° 05’ N 14° 25’ E
Pristina 42° 39’ N 21° 01’ E
Reykjavik 64° 09’ N 21° 58’ E
Riga 56° 53’ N 24° 05’ E
Rome 41° 52’ N 12° 37’ E
San Marino 43° 55’ N 12° 28’ E
Sarajevo 43° 52’ N 18° 26’ E
Skopje 41° 35’ N 21° 03’ E
Sofia 42° 43’ N 23° 02’ E
Stockholm 59° 23’ N 18° 00’ E
Tallinn 59° 22’ N 24° 48’ E
Tirana 41° 02’ N 19° 48’ E
Vaduz 47° 09’ N 9° 31’ E
Valletta 35° 53’ N 14° 31’ E
Warsaw 52° 35’ N 21° 05’ E
Vatican 41° 54’ N 12° 27’ E
Vienna 48° 13’ N 16° 22’ E
Vilnius 54° 04’ N 25° 19’ E
Zagreb 45° 49’ N 15° 58’ E
* apply to the product ZCM-12P/U
WARRANTY CARD
There is 24 months guarantee on the product
Salesman stamp and signature, date of sale
1. ZAMEL provides a two-year warranty for its products.
2. The ZAMEL warranty does not cover:
a) mechanical defects resulting from transport, loading / unloading or other circumstances
b) defects resulting from incorrect installation or operation of ZAMEL products;
c) defects resulting from any changes made by CUSTOMERS or third parties, to products sold or equipment necessary for the correct
operation of products sold;
d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable;
e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear);
3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.;
4. ZAMEL will review complaints in accordance with existing regulations.;
5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL.
6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy be-
tween the goods and the contract.
Programmer type:
11 - week (1 channel)
12 - week (2 channel)
31 - astronomical
Device type
Power supply:
ZCM-xx - 230 V AC
ZCM-xx/U - 24 ÷ 250 VAC
30 ÷ 300 V DC
22 - weekly - year
L(+**)
L(+) / N(-)
N(-**)