Zanussi ZHP615 Instructions for use

Cappa
Cooker hood
Hotte de cuisine
Dunstabzugshaube
Dampkap
MANUALE DI INSTALLAZIONE, USO E MANUTENZIONE
INSTALLATION, USE AND MAINTENANCE HANDBOOK
MANUEL D’INSTRUCTIONS POUR L’INSTALLATION, L’EMPLOI ET L’ENTRETIEN
HANDBUCH FÜR INSTALLATION, BEDIENUNG UND WARTUNG
INSTRUCTIES VOOR MONTAGE, GEBRUIK EN ONDERHOUD
ZHP 615

8GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS 9
CHARACTERISTICS 10
INSTALLATION 11
USE 13
MAINTENANCE 13

9GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

10GB
CHARACTERISTICS
Dimensions
Components
Ref. Q.ty roduct Components
11 Hood Body, omplete with: Controls, Light,
Blower, Filters
20 1 Closing element
Ref. Q.ty Installation Components
12a 4 S rews 4,2 x 44,4
Q.ty Documentation
1 Instru tion Manual
1 Warranty
0÷152
280
60
175
ø 120
1
12a
20

11GB
INSTALLATION
Drilling the Support surface and Fitting the Hood
SCREW FITTING
• The hood support surface must be 135 mm
above the bottom surface of the wall units.
• Drill the support with a ø 4,5 mm drill bit, using
the drilling template provided.
• Cut a hole ø 125 mm in size on the support
surface, using the drilling template provided.
• Fixusingthe4screws12a(4,2 x 44,4) provided.
SNA -ON FITTING
• The hood can be installed either directly on the
bottom surface of the wall units (min. 650 mm
above the hob) using snap-on side supports.
• Cut a fitted opening in the bottom surface of
the wall unit, as shown.
• Insert the hood until the side supports snap into
place.
• Lock in position by tightening the screws Vf
from underneath the hood.
12a
135
125125
15
264
60
Vf

12GB
CLOSING ELEMENT
• The space between the edge of the hood and
the rear wall can be closed by applying the
element20 provided, using the screws supplied
for this purpose.
DUCTING TO THE REMOTE BLOWER
The hood must be ducted to the remote blower
using either a flexible or rigid pipe ø 120 mm.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.
• When opening the sliding carriage for the first time after installing the hood, pull it out briskly
until it clicks.
20

13GB
USE
Control panel
LLight Switches the lighting system on and off.
VSpeed Sets the operating speed of the remote
blower:
MAINTENANCE
Grease filters
CLEANING METAL GREASE FILTERS
• The filters must be cleaned every 2 months
of operation, or more frequently for
particularly heavy usage, and can be
washed in a dishwasher.
• Remove the filters one at a time, after
disconnecting the relative fastening
elements.
• Wash the filters, taking care not to bend
them. Allow them to dry before refitting.
• When refitting the filters, make sure that
the handle is visible on the outside.
Lighting
LIGHT RE LACEMENT
40 W incandescent light.
• Remove the metal grease filters.
• Unscrew the bulbs and replace them with new
ones having the same characteristics.
• Replace the metal grease filters.
L
V
0
1

Quest’apparecchio é conforme alla norma europea sulla bassa tensione C.E.E. 73/23 relativa
alla sicurezza elettrica e alle norme europee: C.E.E. 8 /336 relativa alla compatibilità elettro-
magnetica e C.E.E. 3/68 relativa alla marcatura CE.
This appliance complies with European regulations on low voltages, EEC Directive 73/23 on
electrical safety, and with the following European regulations: EEC Directive 8 /336 on
electromagnetic compatibility and EEC Directive 3/68 on EC marking.
Cet équipement est conforme à la norme européenne sur la basse tension C.E.E. 73/23 relati-
ve à la sécurité électrique et aux normes européennes: C.E.E. 8 /336 relative à la compatibilité
électromagnétique et C.E.E. 3/68 relative au marquage CE.
Dieses Gerät entspricht den europäischen Niederspannungsrichtlinien 73/23/EWG zur
elektrischen Sicherheit, den europäischen Richtlinien 8 /336/EWG zur elektromagnetischen
Verträglichkeit und den Richtlinien 3/68/EWG zur CE-Kennzeichnung
Dit apparaat voldoet aan de Europese Laagspanningsrichtlijn 72/23/EEG inzake de elektrische
veiligheid en aan de Europese normen 8 /336/EEG inzake de elektromagnetische compatibiliteit
en 3/68/EEG inzake de CE-markering.
4360013 4 01 - 021008