Zanussi ZHC 631 Manual

Cappa
Cooker hood
Hotte de cuisine
Dunstabzugshaube
Dampkap
ZHC 631
MANUALE DI INSTALLAZIONE, USO E MANUTENZIONE
INSTALLATION, USE AND MAINTENANCE HANDBOOK
MANUEL D’INSTRUCTIONS POUR L’INSTALLATION, L’EMPLOI ET L’ENTRETIEN
HANDBUCH FÜR INSTALLATION, BEDIENUNG UND WARTUNG
INSTRUCTIES VOOR MONTAGE, GEBRUIK EN ONDERHOUD

11 GB
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual, your
appliance will give you constant high
performance and will remain efficient for
many years to come.
CONTENTS
RECOMMENDATIONS AND SUGGESTIONS 12
CHARACTERISTICS 13
INSTALLATION 15
USE 18
MAINTENANCE 19

12
GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
•The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
•The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
•Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
•For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
•Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm. The route of the flue must be as short as possible.
•Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
•If the extractor is used in conjunction with non-electrical appliances
(e.g. gas burning appliances), a sufficient degree of aeration must be
guaranteed in the room in order to prevent the backflow of exhaust
gas.Thekitchenmusthaveanopeningcommunicatingdirectlywith
the open air in order to guarantee the entry of clean air.
USE
•The extractor hood has been designed exclusively for domestic use
to eliminate kitchen smells.
•Never use the hood for purposes other than for which it has ben
designed.
•Never leave high naked flames under the hood when it is in
operation.
•Adjusttheflameintensityto directitonto thebottomof thepanonly,
making sure that it does not engulf the sides.
•Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
•The hood should not be used by children or persons not instructed in
its correct use.
MAINTENANCE
•Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
•Clean and/or replace the Filters after the specified time period.
•Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

13 GB
CHARACTERISTICS
Dimensions
559
598
90
min. 740
max. 940
735
260
300
86
28
424
00 259
50
650 min.

14
GB
Components
Ref. Q.ty Product Components
1Hood Body, complete with: Controls, Light,
Blower, Filters
2Telescopic Chimney comprising:
2.1 Upper Section
2.2 Lower Section
8a Right Air Outlet Grill
8 Left Air Outlet Grill
9Reducer Flange ø 50- 20 mm
14 Hood Body Air Outlet Extension Piece
consisting of two Half Shells
14.1 2Air Outlet Connection Extension
15 Air Outlet Connection
Ref. Q.ty Installation Components
7.2.1 2Upper Chimney Section Fixing Brackets
11 6Wall Plugs
12a 6Screws 4,2 x 44,4
12c 6Screws 2,9 x 6,5
Q.ty Documentation
Instruction Manual
Warranty
2.1
2.2
2
1
9
14.1
15
14
8 8a
12c
12a 7.2.1 11
11
12a

15 GB
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
•Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of
the area in which the hood will be installed.
•Draw a horizontal line at 650 mm above the hob.
•Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the
centre (notch) with the vertical reference line.
•Mark the wall at the centres of the holes in the bracket.
•Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch) with the vertical line.
•Mark the wall at the centres of the holes in the bracket.
•Mark a reference point as indicated at 116 mm from the vertical reference line and 350 mm above the
horizontal reference line.
•Repeat this operation on the other side.
REAR PANEL (OPTIONAL)
The Rear Panel must be fitted before fixing the hood body and, for both upper and lower position fixing,
must be fitted at the correct height prior to installing the bases. As this operation is rather complex, it
shouldbecarriedouteither by the kitchen installer or a qualified person who knows the final dimensions
of the units.
For the upper fixing position, proceed as follows:
•Rest the back panel on the base, inserting the lower plate between the upper surface and the wall,
centring it on the vertical reference line.
•Mark the centres of the two holes in the upper plate.
•Drill ø8 mm holes at all the centre points marked.
11
12a
H 350 X
6
÷2
6
650 min.
7.2.1

16
GB
•Insert the wall plugs 11 in the holes.
•Fix the brackets using the 12a screws supplied.
•Insert the two screws 12a supplied in the hood body fixing holes, leaving a gap of 5-6 mm between
the wall and the head of the screw.
•Fix the back panel (where present) using the 12a screws (4,2 x 44,4) supplied.
Mounting the hood body
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø150 or 120 mm, the choice of which is left to the installer.
•Before attaching the hood body, tighten the two
screws Vr located on the hood body mounting
points
•Hook the hood body onto the screws 12a
•Fully tighten support screws 12a
•Adjust screws Vr to level the hood body
•To install a ø120 mm air exhaust connection,
insert the reducer flange 9on the hood body
outlet.
•Fix the pipe in position using sufficient pipe
clamps (not supplied).
•Remove any activated charcoal filters.
12a
Vr
9
ø 120ø 150

17 GB
RECIRCULATION VERSION AIR OUTLET
ELECTRICAL CONNECTION
•Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.
Flue assembly
•Assemblethe two halvesofthe hood bodyextension
piece 14
•Pushfit theassembled hoodbodyextensionpiece14
onto the air outlet
•Push fit connection 15onto the hood body extension
piece 14
•Insert the connection extension pieces laterally 14.1
in connection 15
•Makesurethat theoutletoftheextension pieces14.1
is horizontally and vertically aligned with the
chimney outlets.
•If this is not the case, adjust the position by either
reversing the connection extension pieces 14.1or by
cutting the hood body extension 14 along one of the
thinner section channels denoting the pre-fixed
lengths, then reassemble as described previously.
•Theairoutletdirectionalgrillsmustbefittedafterthe
lower outlet duct has been installed
•Ensure that the activated charcoal filters have been
inserted.
Upper exhaust flue
•Slightlywiden the twosides of theupperflue and
hookthembehindthebrackets7.2.1,makingsure
that they are well seated.
•Secure the sides to the brackets using the 4
screws 12c supplied.
Lower exhaust flue
•Slightly widen the two sides of the flue and hook
them between the upper flue and the wall,
making sure that they are well seated.
•Fixthelowerpartlaterallytothehoodbodyusing
the 2 screws 12c supplied.
•On the recirculation version, fit the directional
grids 8a – 8b in their housings making sure that
the directional symbols are towards the top and
front of the hood. Also make sure that they are
correctly inserted in the connection extension
pieces 14.1.
14
14.115
8a
8
12c
8a
2.1
2.2
2
8
7.2.1
12c

18
GB
USE
Control panel
LLight Switches the lighting system on and off.
SLed Motor running led.
V1 Motor Switches the extractor motor on and off at low speed. Used to provide a
continuous and silent air change in the presence of light cooking vapours.
V2 Speed Mediumspeed, suitableformost operatingconditions giventheoptimum treated
air flow/noise level ratio.
V3 Speed Maximum speed, used for eliminating the highest cooking vapour emission,
including long periods.
L
V1 V2 V3S
0 - 1 MID MAX 0 - 1

19 GB
MAINTENANCE
Grease filters
CLEANING METAL SELF-SUPPORTING GREASE FILTERS
Odour filter (Recirculation version)
REPLACING THE ACTIVATED CARBON FILTER
Lighting
LIGHT REPLACEMENT
The filters must be cleaned every 2 months of oper-
ation, or more frequently with heavy usage, and can
be washed in a dishwasher..
•Remove the filters by releasing the fixing hooks.
•Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
•When refitting the filters, make sure that the
handle is visible on the outside.
This filter is not washable and cannot be regener-
ated, and must be replaced approximately every
four months of operation, or more frequently with
heavy usage.
•Remove the metal grease filters.
•Remove the saturated activated carbon filter by
releasing the fixing hooks.
•Fit the new filter by hooking it into its seating.
•Replace the metal grease filters.
40 W incandescent light
•Remove the metal grease filters.
•Unscrew the bulbs and replace them with new
ones having the same characteristics.
•Replace the metal grease filters.