zaxe X3 User manual

User Manual
EN 1 - 26
TR
26 - 54

Foreword/Index
2
1. Part of the Product
Exterior View
Detailed View
Print Head Details
5
6
7
9
10
10
11
14
16
17
18
19
20
22
23
24
25
8
826
4. Introduction
The Unboxing
Configuration
Plugging the Power Cord
Filament Loading
Calibration
Wi-Fi Connection
Pre-Printing
xDesktop Setup
5. Printing Process
Printer Selection and Uploading
Adjusting the Model
Slicing
Uploading via Wi-Fi
Uploading via USB
Removing the Print From the Bed
2. Inside the Box
3. Technical Information 6. Support
Dear User,
Thank you for choosing Zaxe 3D printers. Before using your product, please read the user manual.
Read the instructions carefully. The user manual will give you basic information about your product, safety
measures, maintenance and tips for your first print. Failure to follow these instructions may result in property
damage and injuries. It may also cause malfunctions or poor quality printing results.

Warnngs
3
Power Source should be 230 VAC/ 50
Hz(EU) or 110 VAC / 60 Hz(US); do not plug
your printer to any other power sources
then these as it may cause serious damage
to your device
As it will affect the printing
quality please set your printer on
a flat and well balanced surface.
Hot surface! Wait for the table
to cool down before touching.
While placing the Magnetic PEI plate be
careful not to damage the electronic traces.
It might case some serious harm to on your
device.
We recommend you set up a
well-ventilated room that is dedicated
only to 3D printing.
Please try not to stay in the same
room with the devices for a long
period of time. Vapors that are
produced while printing does not pose
a direct threat to your health but on
the long run when it gets combined
with the accumulated dust particles it
might pose a threat.
Tools in the starter kit box and
accessories for the intended use
should be used with special care.
Wrong use can cause serious injuries.
When you unplug the power cord,
pull the plug instead of the cable. It
will reduce the risk of damaging the
plug or the AC outlet.

Warnngs
4
Do not put your hand between
mechanical components.
Always use protective gear
while using your printer.
Device should be operated in
temperatures between 20-30°
C (68-86° F)
While printing with PLA, FLEX and PETG
half-opening the HEPA filter according to
the picture above will improve your
printing quality. When printing ABS or
ASA, Hepa Filter should always be closed
Do not operate your printer
while there are flammable and
volatile materials in the
environment.
Keep your 3D printer out of
reach of your pet and children.
Warning!

1. Parts of the Product
Exteror Vew
5
Front Doors
Top Lid
Touch Screen
Side Window
USB Ports

1. Parts of the Product
6
On / Off Button
Spool Holder
HEPA Filter
Detaled Vew
Ethernets Port

1. Parts of the Product
7
Step Motor
Cooling Block Fan
Fan Duct
Fan Channel
Inductive Sensor
Heating Block
Heat Break
Silicon Sock
Nozzle
Extrusion Gear
Prntng Head

2. Insde the Box
3. Techcal Informaton
8
Filament Power Cord
GlueGreasing Oil
Layer Height 25-600 microns
Printing Technology Fused Filament Fabrication (FFF)
Printing Area 220 X 230 X 250 mm
Connection Type Wifi, USB, Ethernet
Device Dimensions 410 x 532 x 546 mm
With Spool Holder 410 x 612 x 546 mm
Printer
Weight 28.3 KG
Software xDesktop
Screen Touch Screen
Sample Print
Side Cutter
Allen Key
Warranty Cerificate

4. Introducton
9
Unboxng
Lift the top cardboard box Lift the printer from handle
spaces and put it on the
dedicated spot for your printer.
Cut the belts
First remove the front
protective foam than the rear
one.
Remove the front protective
foam first, then remove the
one.
Remove the parts that locks
the table and axes.
Lift the table upwards and
remove the toolkit.
Your printer is ready to use
1234
5678

4. Introducton
10
Confguraton
Pluggng the Power Cord
In this section, the installation of your 3D
printer stages and your first print will be
carried out. Set your device on a firm and
well balanced surface. Concussions or
uneven leveling can cause your print
quality to decrease.
Plug the cord into the socket shown in the
image securely and make sure it is in place.
Securely the power cord and make sure it is
in place. Press the power button to power
up your printer.

4. Introducton
11
Flament Loadng
Take out the filament from it’s sealed
bag, cut the tip of your filament with
an angle of 45 degrees.
Extend your spool holder by
gently pulling it and place your
spool on the spool holder.
Load your filament from the
filament entry point. (right under
the filament sensor)
Load your filament till the end
of protective tube.
1 2
3 4

4. Introducton
12
Flament Loadng
Press Setting from the main menu. Go to the Filament Settings. For your first installation choose the Install
Filament option and follow the steps.

4. Introducton
13
Flament Loadng
Print head will be heating up for the
filament installation. Place your filament
on the Spool Holder before the heating
process is over and feed the filament to the
print head.
Filament will be ready for installation after
the print head is heated up. Follow the
steps and wait for the filament installation.
If the installation was successful the
filament will be exiting the nozzle. When the
filament of the right color is installed,
confirm the installation was successful to
start the printing process.

4. Introducton
14
Calbraton
Table calibration should be done when you use your 3D printer for the first time. When you
move it or when you use it for a long time. Bad table calibration can cause many problems
and it may even cause your device to be out of service. Make sure your table calibration is
correct.
If the print doesn't stick to the printing surface or if there isn't any extrusion on the first
layer while it prints, it is generally because of bad table calibration. In case of such an
event, please follow the instructions below.
Choose Settings > Bed Calibration
When the calibration process starts, all axes will return to their starting positions. After
the print head and table heats up, your 3D printer will automatically calibrate the print
table in a couple of minutes.

4. Introducton
15
Calbraton
After the calibration, the print head will
start to print straight lines. You can
press the up and down arrows on screen
to be sure that your print sticks to print
bed according to the picture on screen.If
you set the Z-offset too close or too far
from the bed it will decrease your print
quality.
Print head too close to
the print surface
Print head is in ideal distance
to the print surface
Print head is too far from
the print surface

4. Introducton
16
Firstly, download the files of your X3 from the link below.
X3 File: https://d.zaxe.com/x3
W-F Connecton
To connect your device to Wi-Fi, go to the
connections settings on your computer and
connect to your X3
After the access point is connected, go to
the 192.168.0.1 IP address on your browser.
Change the Radio Mode setting to Client
Mode in the Network Setting menu.
Under the Client Mode section, fill the SSID
section with the name of your local Wi-Fi and
enter your password in the Password section.
As the last step, click on Restart.

4. Introducton
17
Pre-Prntng
This process should always be done while the
print table is cold!
Apply 4-6 layers of glue stick to your PEI
Surface in opposite directions.
Usage of glue sticks differs depending on the
material. Usually for the PEI Surface there is
no need to apply glue stick but, if there is an
adhesion problem do not hesitate to apply it.
After a while, glue will lose it’s function.
Do not reapply it without cleaning the PEI
Surface. You can clean the table with a damp
towel then reapply the glue when it’s dry.
Before printing with your device, applying glue stick
to your print surface is crucial. This process ensures
that your print will stick to the PEI Surface firmly.

4. Introducton
18
xDesktop Setup
With Zaxe printers we suggest the usage of our own slicer xDesktop, which is available
for free on www.zaxe.com./xdesktop.
Open the setup wizard and follow the
instructions.
Choose your installation folder. When the setup wizard is completed, you
can start getting your first print.
Welcome to the xDesktop
Setup Wizard Installation Folder
This will install xDesktop on your computer.
It is recommended that you close all other applications
before continuing
Click Next to contiue or Cancel to exit Setup.
Please specify the folder where xDesktop will be installed.
Next Cancel Next Cancel
xDesktop Setup
xDesktop Setup
Folder Location
Browse...

5. Prntng Process
19
Prnter Selecton and Uploadng
Prepare model for Print
Firstly choose X3 from the top right corner of the xDesktop. xDesktop is compatible with formats
such as .stl , .obj and .amf. You can upload your 3D model by pressing the open model button at
the top left side of the screen or you can simply drag and drop it.
Select 3D Printer

5. Prntng Process
20
Adjustng the Model
You can make small adjustments to your model such as re-locating, duplicating, scaling,
re-orientin, mirroring, adding and removing support manually from the menu at the left
hand side.
With xDesktop you are in full control!
File Edit Settings Help
Open File
Centering
Multiplying
Moving
Scaling
Rotating
Mirroring
Blocking Support Manually
Adding Support Manually