ZeeVee ZyPer4K User manual

Quad ZyPer4K Encoder Card
for Netgear M4300-96X
HDMI 2.0
IP A/V DISTRIBUTION SYSTEM
PART NUMBER: Z4KNGENC4
User Manual
Updated January 2020

About ZeeVee:
ZeeVee is the leading manufacturer of high-quality encoder/modulator/decoder products for
video distribution over any type of transmission media; be it RF coax, fiber, or copper ethernet.
Established in 2007, ZeeVee has been manufacturing industry-leading products while operating
the company responsibly in compliance with the strictest levels of regulatory and environmental
requirements. The standards by which we govern our corporate conduct are far higher than that
required by law.
Our mission is to completely fulfill the toughest customer application requirements with the
highest quality products we can produce. After the sale, we strive to support the customer with
award-winning support and service. Our goal is that no customer shall be ever be dissatisfied.
It is both our mission and our passion.
ZeeVee, Incorporated
295 Foster Street, Suite 200
Littleton, Massachusetts
01460, USA
www.zeevee.com
[email protected]
Phone: [phone]
ii

CONTENTS
Encoder Function 1.................................................................................
Quad Encoder for Netgear M4300-96X 1............................................
Package Contents 2.............................................................................
Installation Instructions and Notes 3....................................................
Product Limitations 3............................................................................
Setting up ZyPer4K in Many to Many Environment 4.............................
ZyPer Management Platform 6.......................................................................
Netgear M4300-96X 7.....................................................................................
Device Technical Specifications 8...........................................................
Encoder HDMI Video Specifications 8.................................................
Physical and Environmental 9..............................................................
Appendix A 10.........................................................................................
Resetting the Z4KNGENC4 Card 10....................................................
Disclaimers 11.........................................................................................
iii

ZyPer4K
Encoder Function
The function of the ZyPer4K Encoder Device (Encoder) is to accept audio and video data over a
variety of interface types, and translate that data to a format suitable for transmission over a
standard 10Gb Ethernet network. The encoder supports inputs up to 4K resolution including full
HDMI 2.0 support. (4K resolution 4:4:4 at 60Hz)
Video data is segmented, encrypted, prepared for transmission, and sent by the Encoder unit.
No unit other than those so designated by the control entity shall be able to receive the video
stream sent by an Encoder.
The format of the IP data is fully in compliance with industry-standard IEEE 802.3 Ethernet
networking practices. Any switch or device capable of passing 10G Ethernet traffic can be
employed to carry ZyPer4K A/V traffic.
Quad Encoder for Netgear M4300-96X
Designed exclusively for use with the Netgear M4300-96X, the ZyPer4K Quad Encoder Card
provides four HDMI 2.0 inputs and the full functionality of four independent encoders.
Port Name
Index
Definition
HDMI Port 1
A
HDMI 2.0 Input port. Capable of up to 4K60 with HDCP2.2 encryption.
HDMI Port 2
B
HDMI 2.0 Input port. Capable of up to 4K60 with HDCP2.2 encryption.
HDMI Port 3
C
HDMI 2.0 Input port. Capable of up to 4K60 with HDCP2.2 encryption.
HDMI Port 4
D
HDMI 2.0 Input port. Capable of up to 4K60 with HDCP2.2 encryption.
IR-OUT
E
Infrared Commands passed back FROM decoders as configured by ZMP.
Port Name
Z4K Quad Encoder
Page of111
A
B
C
D
E
F
G
H
J
K

ZyPer4K
Package Contents
One ZyPer4K Quad Encoder Card
Four IR Emitters
One IR Receiver
!
IR-OUT
F
Infrared Commands passed back FROM decoders as configured by ZMP.
IR-OUT
G
Infrared Commands passed back FROM decoders as configured by ZMP.
IR-OUT
H
Infrared Commands passed back FROM decoders as configured by ZMP.
IR-IN
J
Infrared Commands to be passed TO decoders as configured by ZMP.
RESET
K
Hardware Reset pin. Use paperclip or other tool to hold internal button for 25
seconds to force reset of the Z4KNGENC4 to factory defaults. See Appendix A
for details.
Index
Definition
Port Name
Z4K Quad Encoder
Page of211
IR Emitter (4x)
IR Receiver (1x)
Quad Encoder Card

ZyPer4K
Installation Instructions and Notes
The Z4KNGENC4 card is only compatible with the Netgear M4300-96X switch. The following
instructions should be followed closely to avoid damaging the card or the switch itself. Prior to
installation of the card, please ensure the latest available firmware is installed on the Netgear
M4300-96X switch.
https://www.netgear.com/support/product/M4300-96X.aspx#download
The card must be installed in top row of the M4300-96X switch. Bays 1-6 with the yellow arrows
pointing up as shown in the image below. A maximum of six cards are supported in a single
switch. Cards installed the lower bays will not function.
For the first time installation of the card, power to the M4300-96X must be disconnected.
Failure to disconnect power when installing the card for the first time can result in the card not
being properly identified by the M4300-96X switch.
Note: The Netgear M4300-96X should never be transported with any cards of any kind
installed. Please remove all cards when transporting/shipping the M4300-96X switch.
Product Limitations
The Z4KNGENC4 card provides the functionality of 4 independent ZyPer4K encoders with the
following restrictions/limitations compared to stand alone single encoder boxes.
1. Must use “slim” HDMI cable connectors to allow 4 cables to fit side by side
2. Encoded Video can be routed to individual Full-Screen decoders, or Video Walls.!Multi-View
endpoint targets are not supported by the Z4KNGENC4
3. Preview of Encoded Video not supported by Z4KNGENC4
Z4K Quad Encoder
Page of311

ZyPer4K
Setting up ZyPer4K in Many to Many Environment
A many to many, or switched environment involves connecting many sources to many displays.
ZyPer4K allows you a flexible and scalable amount of input-output options without limitations."
For example, in a 24-port configuration, you can configure a 1x23, 6x18, or 4x20 (and so on)
system. A network switch is needed in these many to many configurations. These environments
also require configuration through the ZyPer4K management software.
To set up ZyPer4K in a multipoint environment, you have to:
•Connect the ZyPer4K Management Platform hardware to the network switch
•Determine the IP Address of the ZMP (See the Management Platform User Guide
for details)
•Connect all Encoders and Decoders to the 10Gb network switch
•Connect a PC or Laptop to the network switch.
•Make sure laptop is on same “network” as the MP
•Open a Chrome browser and point it to the IP Address of the MP. (This opens ZyPer
Management Platform (ZMP))
•Login to the MP using the default username and password. “admin” / “admin”
•All devices (encoders and decoders) will automatically appear in ZMP
Z4K Quad Encoder
Page of411
Fiber or Copper
10 Gigabit
Ethernet Switch

ZyPer4K
•Switch (or route) video from sources to displays
•Drag source onto display to route video/audio
Z4K Quad Encoder
Page of511
Drag and!
Drop
IP Address of MP

ZyPer4K
ZyPer Management Platform
Each Z4KNGENC4 card installed in the system will show up as 4 independent ZyPer4K
encoders in the ZyPer Management Platform.
By default each encoder will be identified by its unique MAC address.
Example MAC: 80:1F:12:5D:8E:AB
Port MAC addresses can be found labeled on the underside of the card. Ports are numbered
from left to right.
The user can rename all of the encoders as desired.
The ZyPer Management Platform will treat the modular encoders just like any other encoders in
the system and allow you to route audio, video and IR from the encoder to any number of
decoders. Audio, Video and IR can all be routed independently.
Please note the Product Limitations on page 4. Modular inputs cannot be routed to a Multi-view.
Z4K Quad Encoder
Page of611

ZyPer4K
Netgear M4300-96X
The Z4KNGENC4 will automatically be detected by the Netgear M4300-96X switch. Media type
will appear as HDMI as shown in the image below:
!
Z4K Quad Encoder
Page of711