Zeggo WLX_BTZ1 User manual

ZEGGO WLX_BTZ1
REV. 1, 03/19 1
Future Integrated Data Evaluation
Wireless Water Leakage
Detector
Model: WLX_BTZ1
USER MANUAL

ZEGGO WLX_BTZ1
REV. 1, 03/19 2
DOCUMENT HISTORY
Release
No.
Date
Revision Description
1
14/12/17
First Release, Water Leakage Detector WLX_BTZ1
V1.0
2
16/04/19
System manual updated
3
14/10/19
Sensor Sensing Interval Info Updated.
4
5
6
7

ZEGGO WLX_BTZ1
REV. 1, 03/19 3
Introduction
Thank you for selecting the Zeggo Wireless Water Leakage Detector. This device transmits sensor
reading wirelessly from remote location to designated gateway for online monitoring. In this package
you will find:
•One Transmitter WLX_BTZ1
•One User Manual
This device is ideal for monitoring the leakage of water of designated environment at 24/7. The data
send to Zeggo platform to enable report generation and send alert to personal device.
The Water Leakage Detector features:
•Secure AES128 IEEE802.15.4 Radio Transmission to Zeggo’s Gateway
•Easy Configuration and Installation
•>2 Years of Battery Life
•Internal storage to store during network failure
•Programmable sampling interval: 1min, 5min, 10min, 15min, 30min
Specification
Battery
3.6V 4400mAh lithium battery, “AA” size
Battery Life
6 months to 3 Years. Depending on environment condition
and transmission time setting. (Innoflex is not responsible for
the specific battery life.)
Radio Frequency
ISM 2.4Ghz
Range of Transmission
Up to 60m Indoor and up to 300m under line of sight
(Depends on site condition)
Operating Condition
0°C to 70°C
Sensor Type
External Water Leakage Detector Probe (M8 Connector)
Measurement Type
Non-corrosive and electricity conductive liquids
Category of resistance to heat
and fire
UL94-V0 (Casing)
Size
3.6” x 2.6” x 1.7”

ZEGGO WLX_BTZ1
REV. 1, 03/19 4
Product Description
Figure 1: WLX_BTZ1 Description
Product Introduction
WLX_BTZ1 Water Leakage Detector functions as a remote transmitting device. A gateway with
internet access must within the range that the sensor reading can successful transmit over to the
gateway. The radio range between transmitter and gateway varies significantly based on the site
environment and surrounding objects (metal walls, furniture etc.). The compatible model of Zeggo’s
gateway for WLX_BTZ1 is:
•Zeggo Gateway, GWA_12Z1
Startup Operation
Water Leakage Detector equipped with full battery at the time of delivery. It is always a good practice
to check that the device is ALIVE prior to the installation by turn ON/ OFF the device. By pressing and
holding the button for an interval, blinking and colour of status LED will indicate current ON/OFF status.
Table 1: Turn On/Off Operation
Button Press and Hold Period
Status LED Behaviour
ON/OFF Status
> 3 second
Flashing of Green LED
Turn ON
> 5 second
Light up Red LED
Turn OFF/ Go into Sleep
A signal will send out to the gateway immediately after turned on accompany with blinking of LED
indicating the operation status. Green LED indicated the data reading is successfully sent and
received by gateway. On the other hand, flash of Red LED shows a transmission failure or sensor
fault.
Configuration Button (ON/OFF)
Status LED (Green, Red Bicolour)
M8 Connector (For External Probe)
Flange

ZEGGO WLX_BTZ1
REV. 1, 03/19 5
During start up, the device sent out a signal every 6 second and there is a total of 6 start up
transmission cycle. It is useful to check the transmission status during starting period (about 36
seconds) before device going into normal operation which has longer transmission interval. Start up
operation can trigger repeatedly every turning on device from off state.
Mounting
Avoid placing the device close to a metal object that may affect the transmission range. Depends on
installation location, devices can be installed by using screw with plastic wall plug number of 6 on
both flange of the enclosure. For surface mounting, surface shall be cleaned to ensure free of grease,
water and dust.
Sensor Connection
Connect only Water Leakage Detector Probe to the device. Connection points refer to P1 and P2
(non- polarity) in the diagram below.
P2
P1
N/A
N/A

ZEGGO WLX_BTZ1
REV. 1, 03/19 6
Configuration
Binding & Sensor sensing Interval Setting
Device will enter configuration mode from special sequence button press and hold.
i) Make sure the device is in OFF state and wait for about 4 second.
ii) Press the ON/OFF/configuration button for 4 times. (Interval must less than 2 secs)
iii) Press and hold the button for the 5th attempt.
The status LED will blink GREEN and RED alternately upon successful enter configuration mode. If the
status LED blink GREEN LED only, it fails to enter configuration but goes into normal ON mode. Kindly
follow the steps again for another attempt. Once successfully enter the configuration mode, device
will receive binding command. It will automatically search for the nearest gateway and binding to
it after exit and turn on the device. Communication will begin upon a successful binding.
During configuration mode, 10 secs timeout is implemented if no input is received. Each press and
release of button will increase a step in the sensor sensing interval setting as below:
Table 2: Sensor Sensing Interval Setting
Green Status LED Number of Blinking Times
Sending Interval Setting
1
5s
2
10s
3
15s
4
30s
5
60s
Once the correct setting has been set, leave it for about 10 seconds to exit the configuration mode.
The device will back into OFF state. It will bind to nearest gateway and follows the transmission
interval setting after turned ON (after startup cycle finished).
*Remark: WLX_BTZ1 model detects the change of state from its sensor input. The change of state
detected is sent out at every 15 minutes interval.
Internal Memory Backup
In the event when signal failed to send to a gateway, sensor data stores in the internal memory. These
backup data will send again to gateway after network recovery. The maximum backup period depends
on sending interval setting.
Table 5: Maximum Backup Period
Transmission Interval
Maximum Backup Period*
1 min
7 days
5 mins
37 days
10 mins
75 days
15 mins
113 days

ZEGGO WLX_BTZ1
REV. 1, 03/19 7
30 mins
227 days
*In condition all the previous backup data has been successfully send out from the initial.
Battery Level & Signal Level
Table 6: Device Battery Life
Transmission Interval
Device Battery Life
1 min
6 months
5 mins
2 years
10 mins
3 years
15 mins
3 years
30 mins
3 years
The battery life is purely indicative as it mainly depends on transmission interval setting, installation
environment condition and quality of wireless connection. If the device fails to communicate with the
gateway, it will consume more power to search the gateway and restore connection.
Both the battery level and signal level of the device can be view from Zeggo’s portal. It is
recommended to replace the battery if battery level is less than 20%. The suggested signal percentage
for a stable connection is >40% to take care the moving object or addition of object in between signal
path.
Information Regarding Product Disposal
This product contains Lithium Thionyl Chloride Battery. There are a fire, explosion, and severe burn
hazard. Do not burn or expose the battery to high temperatures. Do not recharge, crush, disassemble,
or expose the contents to water. Properly dispose of used batteries in accordance with applicable
regulations in country. A disposal service could offer upon request.

ZEGGO WLX_BTZ1
REV. 1, 03/19 8
Limited Warranty & Limitation of Liability
Innoflex Pte Ltd warrants that the hardware of product will be free from material defects in
workmanship and materials under normal use in accordance with Innoflex instructions and directions
from the purchase date of the product, for the period (“Warranty Period”), except as otherwise stated
herein.
• Hardware: One (1) year
At its option, Innoflex will repair or replace at no charge the product which proves to be defective
within such warranty period. The warranty extends only to the original buyer or end-user customer of
a Innoflex authorized reseller, and does not apply to fuses, disposable batteries or to any other
product which, in Innoflex’s opinion, has been misused, altered, neglected, or damaged by accident
or abnormal conditions of operation or handling. Any replaced or repaired products or parts carry a
ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.
INNOFLEX MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS MANUAL
AND, IN NO EVENT SHALL INNOFLEX BE LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY
OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE
OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT,
FAILURE OF OTHER EQUIPMENT TO WHICH PRODUCT IS CONNECTED WITH) RESULTING FROM THE
SUE OF PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BEACH OF THIS
LIMITED WARRANTY, EVEN IF INNOFLEX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT
OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF
INNOFLEX UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED
BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE
AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.
All rights of the attached documents belong to Innoflex Pte Ltd. It is prohibited to use, duplicate and/
or arrange a part of whole of the attached documents without prior written to/ permission of Innoflex
Pte Ltd. Specification, software, design and other contents outlined in the attached documents are
accurately describe at the time of publication and subject to change without notice in the interest of
constant product development. All registered trademarks, product names and logos mentioned
herein or for products being used are the property of Innoflex Pte Ltd or of their respective owners.
The products are not designed nor intended for use in safety-critical, automotive, military or
aerospace applications or environment unless specifically designated by Innoflex Pte Ltd.
Innoflex Pte Ltd
3015 Ubi Road 1,#02-218 , 408704 • Singapore.
Phone: [phone]

ZEGGO WLX_BTZ1
REV. 1, 03/19 9
Email: [e-mail]
www.zeggo.com.sg
Subject to change without notice. • Copyright © 2017 • Printed in Singapore