Zenitel ICX-510-IA User manual

Mounting & Installation Manual
ENA100K12241
v1.0
ICX-510-IA

2 3
This document serves as a basic mounting and installation guide for the ICX-510-IA
Intelligent Communication Gateway.
The ICX-510-IA product package comprises the following components:
Item Number Item Name Description
1002000110 ICX-510-IA Intelligent Communication Gateway incl ICX-
AlphaCom Core
1002500010 IA-RS1 Rack Shelf for ICX-510
1002500020 IA-MB1 Mounting Bracket for ICX-510
1002510000 IPS-AC1 PSU, Input 85-264 VAC, Output 48 VDC, DIN-Rail
About
Safety information
This manual describes the necessary steps to install the ICX-510-IA. It contains
important instructions that must be followed. ICX-510-IA must be installed by a
trained technician in accordance with national and local regulations.
Zenitel takes no responsibility for damages caused by improper or inadequate
mounting.
The ICX-510-IA is intended for use in restricted access areas for trained service
personnel and/or operators, and is not to be installed in locations where children are
likely to be present.
Front View
Item Description Comment
1Power LED Steady green when power is applied to the ICX-510-IA
2Status LED Flashing green when the ICX-510-IA is running
3Fault LED Steady amber when the system reports an error. The LED will be lit during
application or system reset, or if there is a temperature alarm.
4Active LED
Steady blue when the ICX-510-IA is operational. In a system with redundant serv-
ers, the Active LED will be lit on the operational gateway, and not lit on the standby
gateway
5Link LED Steady green when the Ethernet link 0 or 1 is up. There is one LED for each Ether-
net port
6RX/TX LED Flashing when receiving or transmitting data on Ethernet port 0 or 1.
7Securing hole 2 x screw holes, diagonally placed, for M4 screws. Used for rack mounting
Description
123
45
6
7
7

4 5
Rear View
Item Description Comment
1Status LEDs Indicates the same as the LED lights on the front of the
box.
2Ethernet port Eth0 / Eth1 Two 1 Gbps Ethernet interfaces. Each Ethernet port is
equipped with LED indicators for link and activity.
3Power in 24-48VDC
ICX-510-IA is powered by a DC power supply with
nominal voltage 24VDC or 48VDC (Min/Max: 20VDC-
63VDC)
4Console port RS232 RJ45
RS232 port is the RJ45 part of the dual connector
RS232/USB. This is a console port for debugging
purposes. Com parameters: 115.200 baud, 8 data bits, no
parity, 1 stop bit.
5USB A port
6USB Micro-B
7Fault Relay 3 pole terminal
block
Fault relay is used to indicate system status together with
Fault LED
8SD card slot Used for external storage or system recovery
9Factory Default Button Tact switch Used for resetting ICX-510-IA to factory default settings
1
23
4
56
7
8
9
Wall / shelf mounting
The ICX-510-IA can be mounted on any flat surface such as a wall or shelf using
the IA-MB1 Mounting Bracket. The following example is the procedure for wall
mounting.
1
2
HxW: 120x90 mm
Skip this step
if mounting on
wood or steel surface
Drill Bit 5 mm

6 7
3
3x Flat Head Washer
Screws, ø4.2 x 25 mm
3x Nylon Plugs 5 mm
(not included)
4
4x Mounting clips
52A blanking front can be inserted into the
unused position if only one slot is required.
Rack mounting
Use the IA-RS1 Rack Shelf when mounting the ICX-510-IA into a 19” 1HU rack. Two
ICX-510-IA units can be placed side by side on the rack shelf.
1(2x) 4x Mounting clips

8 9
3
42x M4x8mm countersunk screws
The securing holes can also be used to mount
the unit to a shelf other than the IA-RS1.
Note that the maximum insertion depth is 6 mm.
Installation
Network
Connect the ICX-510-IA to the IP network. Use an Ethernet cable. Connect the
cable to Ehernet Port 1.
1
IP
network
2Power supply
Mount the IPS-AC1 power supply on
a DIN rail and terminate the power
cables.
+ Power out
Power in
L1 N

10 11
3Ferrite
Before connecting the cable to the ICX-510-IA, the included Snap On Ferrite
(EMKOB99121) must be attached near the end of the cable.
4Connect the ICX-510-IA
Connect the power cable to the ICX-510-IA. Then connect the power supply to
a 100-240VAC power source.
Start up
Power up the IXC-510-IA.
Watch the LEDs. During startup the Power LED and the Fault LED will be lit.
When up and running, the green status LED will start flashing.
Connect a laptop to Ethernet port 0. Use an Ethernet cable.
1
3
2
Connect to web server - ICX Web. The ICX-510-IA comes with an embedded
web server which provides functions for system configuration, monitoring and
upgrade.
Open a web browser (e.g.Firefox or Chrome), and log on to the web server
using IP address 169.254.1.5.
4
Enter the link or scan the QR-code below to go to Zenitel Wiki for configuration
instructions.
Zenitel Wiki: wiki.zenitel.com/wiki/Main_Page.
5

12 13
Contact Information
Visit zenitel.com to find your country’s contact information.
Technical specifications Value
Weight 1 kg / 2.2 lbs
Dimensions (WxHxD) 162x44.5x200mm / 6.4’’x1.75’’x7.9’’
Relative humidity < 95% not condensing
Operating temperature range -15° to 5° C / -40° to 131 ° F
Encapsulation material Aluminium
Power Nominal 24VDC - 48VDC, 15 W (min/
max: 20VDC-63VDC)
Specifications
The WEEE Directive does not legislate that Zenitel, as a ‘producer’, shall collect ‘end
of life’ WEEE.
This ‘end of life’ WEEE should be recycled appropriately by the owner who should use proper
treatment and recycling measures. It should not be disposed to landfill.
Many electrical items that we throw away can be repaired or recycled. Recycling items helps to
save our natural finite resources and also reduces the environmental and health risks associated
with sending electrical goods to landfill.
Under the WEEE Regulations, all new electrical goods should now be marked with
the crossed-out wheeled bin symbol shown.
Goods are marked with this symbol to show that they were produced after 13th
August 2005, and should be disposed of separately from normal household waste so
that they can be recycled.
Zentel hereby declares that this product is in compliance with the essential requirements
and other relevant procisions of deirective 2014/53/EU and all other applicable EU directive
requirements. The complete declaration can be found at www.zenitel.com

DOC. NO.
Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising from the information therein. Zenitel,
Vingtor-Stentofon and Phontech products are developed and marketed by Zenitel. The company’s Quality Assurance System is certified to meet the requirements
in NS-EN ISO 9001. Zenitel reserves the right to modify designs and alter specifications without notice. ZENITEL PROPRIETARY. This document and its
supplementing elements contain Zenitel or third-party information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited, if
not otherwise explicitly agreed in writing with Zenitel. Any authorized reproduction, in part or in whole, must include this legend: Zenitel – All rights reserved.
[e-mail]100K12241
v1.0