Zetta Z82 User manual

Zetta Z82 Security Camera Quick Start Guide
www.zetta.com.hk
Overview
Congratulations on your purchase of Zetta Z82 security camera!
Zetta Z82 is an intelligent security camera with multiple triggering methods and multi auto
on/off modes. The camera comes with a built-in rechargeable battery which can record up to
9 hours continuous video and audio during typical use and standby for 1 month when motion
triggering (in max battery mode) is enabled. By plugging in a 5V DC adapter (not included),
it can achieve max 156 hours circular recording for surveillance on a 256GB microSD card.*
* Actual life and performance may vary depending on usage and settings; battery not replaceable
Features
Circular recording – loop back recording once memory card is full
Time stamp – put time stamp on video
Motion-triggered recording – select to record only when motion is detected, 1 month
standby (in max battery mode), work through glass and window
Auto gapless split le – gaplessly split les for every 10 / 15 / 20 minutes
Orientation – use when the camera is turning up-side-down
Full HD 1080p resolution
Congurable video quality – high / medium / low
Support max 256GB microSD(TF) card (for better performance, use card larger than
8GB, class 4 or above, and before use, format the card to FAT32 format only)
Package Contents
Please unpack your intelligent security camera and check that the following are included:
Zetta Z82 security camera
USB 2.0 Cable
Quick Start Guide
Note: The PC conguration tool “Camera Widget” is not included in the package, please
download it from http://www.zetta.com.hk
Charging
The camera comes with an internal rechargeable battery. To use the camera for the rst time
or not using the camera for a long time, please fully charge the battery for at least 8 hours
and resync the time by using the Camera Widget (see section “PC Conguration Tool”). You
can charge your camera through the USB port of your computer, or an portable power bank,
or a 5V DC adapter or car charger.
To charge the battery through USB port, connect the USB cable to the USB port of the
computer and the camera. For details, please see the status below. The camera will function
as a mass storage device, you will not be able to record video at this moment.
To charge the battery through power bank, DC adapter or car charger, connect the charger
to the camera. For details, please see the status below. You will be able to record video while
charging, depending on the mode you set.
Recording
The power button is located at the back side of the camera. It can turn the camera on or off.
Start Recording
Insert a FAT32-formatted microSD card (please see “Format Card” on how to format the
card). Press and hold the Power button until the green LED is on (approximately 3 seconds),
and then release the button. When you see the green LED ashing, the camera is recording.
Otherwise, please see the status below.
Stop Recording
Press and hold the Power button until the orange LED is off (for approximately 3 seconds).
WARNING: Turn off the camera before removing the microSD card!
Status
Without external charger
Green LED on: camera is booting up
Green LED ashing: normal recording
Green / Red LED intermittent ashing: battery low and recording
Red LED on: no card, card fail, battery low or card full (not in circular recording)
Connecting to an external charger
Orange LED on: charging but no recording
Green LED on: charging completed but no recording
Green LED ashing: charging completed and recording
Green / Orange LED intermittent ashing: charging and recording
Red LED on: no card, card fail or card full (not in circular recording)
Connecting to computer
Orange LED on: charging
Green LED on: charging completed
Zetta Z82 at a Glance
Camera
Motion sensor USB
Microphone
Firmware upgrade
or Format card Reset
microSD
Power

Zetta Z82 Security Camera Quick Start Guide
www.zetta.com.hk
FCC Regulation
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and then on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1.Increase the separation between the equipment and camera.
2.Connect the equipment to a different outlet so that the equipment and camera are
on different branch circuits.
3.Consult the dealer or an experienced radio / TV technician for help.
Customize setting
For custom mode conguration, please use the PC conguration tool “Camera Widget” to
change the settings. The widget can be downloaded from http://www.zetta.com.hk.
Connecting to computer
To connect the camera to your computer, follow these instructions:
1 Connect the larger end of USB cable to an available USB port of the computer
2 Connect the smaller end of the cable to the USB port of the camera
3 The camera will appear in My Computer as a removable drive
PC Conguration Tool (Camera Widget)
To synchronize the time and customize settings, download the PC conguration tool (Camera
Widget) from www.zetta.com.hk and follow the instruction in the software guide.
REMARK: If the time shown is year 2030 or after due to loss of Real Time Clock,
please use the widget to resync the time. The les with incorrect time stamp will be
moved to the ZETTA_ERR folder. Please delete the les if they are not needed.
Firmware upgrade
Zetta will from time to time release new rmware for enhancement or adding new features.
Visit www.zetta.com.hk to check it out.
Custom (default)
Video Quality* (High) / Medium / Low
Indoor Lighting
Condition
(50Hz) / 60Hz
Orientation (Normal) / Up-side-down
Timestamp (Enable) / Disable
Circular Recording (Enable) / Disable
Split File Time (min) 10 / (15) / 20
Mic (Enable) / Disable
LED On/Off (On) / Off
Motion-Trigger
Sensitivity**
High / Medium / Low / (Disable)
Power Option*** Always On / (Max Battery)
* Memory usage:
Video Quality High: 3GB / hour
Video Quality Medium: 2GB / hour
Video Quality Low: 1.5GB / hour
** If triggering is enabled, the Z82 will record for 10 seconds after powering up. Then it will go into
standby. If there is trigger, it will keep recording until there are no further triggers. After that, it will
record for 1 more minute and then standby again.
*** When Always On is selected, Z82 will not record but the system will remain on. There will be 1 second
delay in the recording after triggering. When Max Battery is selected, the system will standby and there
will 4 seconds delay in the recording after triggering.
version: 1.0
Environmental Requirements
Storage temperature: 32˚ to 113˚F (0˚ to 45˚C)
Operating temperature: 32˚ to 113˚F (0˚ to 45˚C)
Minimum System Requirements
Windows XP, Vista, 7, 8, 10
Mac OS 10.9 or above
USB 2.0 port for hi-speed transfers and charging
Technical Support
Before contacting us, please visit the “Support” section in http://www.zetta.com.hk. For
further questions on feature and usage, please contact us at (852) 31884492 or (1) 415373
6020
Manufacturer
Zetta Systems Limited
Email: [email protected]
Format card
For card >=64GB, it must be formatted to FAT32 before use.
To format a card, please follow this:
1. Insert the card into Z82
2. Connect Z82 to a power bank or micro USB charger (not included) until orange light is on
3. Use a pin to press and hold the upgrade button (at the back of the camera, next to the
micro USB socket) until the red light is ashing
4. Release the upgrade button
5. Press and hold the upgrade button again until the green light is ashing
6. Disconnect the USB charger or power bank, the format is completed