Zetta Z86 Security Camera Quick Start Guide
Customize setting
For custom mode configuration, please use the PC configuration tool “Camera Widget”
to change the settings The widget can be downloaded from http://www zetta com hk
Custom (default)
Video Quality*
(High) / Medium / Low
Indoor Lighting
(50Hz) / 60Hz
Condition
Orientation
(Normal) / Up-side-down
Timestamp
(Enable) / Disable
Circular Recording
(Enable) / Disable
Frame rate (fps)
(30) / 15
Mic
(Enable) / Disable
LED On/Off
(On) / Off
Motion-Trigger
High / Medium / Low / (Disable)
Sensitivity**
Power Option***
Always On / (Max Battery)
*Memory usage:
Video Quality High: 3G / hour
Video Quality Medium: 2G / hour
Video Quality Low: 1.5G / hour
** If triggering is enabled, the Z86 will record for 10 seconds after powering up. Then it will go into
standby. If there is trigger, it will keep recording until there are no further triggers. After that, it
will record for 1 more minute and then standby again.
*** When Always On is selected, Z86 will not record but the system will remain on. There will be 1
second delay in the recording after triggering. When Max attery is selected, the system will standby and
there will 4 seconds delay in the recording after triggering.
Format card
For card >=64GB, it must be formatted to FAT32 before use
To format a card, please follow this:
1 Insert the card into Z86
2 Connect Z86 to a power bank or micro USB charger (not included) until orange light is on
3 Use a pin to press and hold the upgrade button (at the back of the camera, WITHOUT
any wording) until the red light is flashing
4 Release the upgrade button
5 Press and hold the upgrade button again until the green light is flashing
6 Disconnect the USB charger or power bank, the format is completed
Manufacturer
Zetta Systems Limited
Email: support@zetta com hk
PC Configuration Tool (Camera Widget)
To synchronize the time and customize settings, download the PC configuration tool
(Camera Widget) from www zetta com hk and follow the instruction in the software guide
REMARK: If the time shown is year 2030 or after due to loss of Real Time Clock,
please use the widget to resync the time. The files with incorrect time stamp will
be moved to the ZETTA_ERR folder. Please delete the files if they are not needed.
Minimum System Re uirements
Windows XP, Vista, 7, 8, 10
Mac OS 10 9 or above
USB 2 0 port for hi-speed transfers and charging
Connecting to computer
To connect the camera to your computer, follow these instructions:
1
Connect the larger end of USB cable to an available USB port of the computer
2
Connect the smaller end of the cable to the USB port of the camera
3
The camera will appear in My Computer as a removable drive
App (Cam Widget)
The Z86 also supports local wireless preview, please install the app "Cam Widget" on Android
or iOS devices
1 Connect the Z86 to a computer and use the Camera Widget software to enable wifi
2 Safely eject the drives and turn on Z86
3 Turn on phone wifi and connect to Z86
4 The default password is dvrdvrdvr
5 When asked, please choose "stay with wifi" or "always connect" and disable smart
switching If not ok, please do "forget network" in wifi setting and restart the phone and try
again
6 Run the app "Cam Widget" on the phone
7 You can do local preview, browse microSD card content or change settings through the
app
Firmware upgrade
Zetta will from time to time release new firmware for enhancement or adding new features
Visit www zetta com hk to check it out
Technical Support
Before contacting us, please visit the “Support” section in http://www zetta com hk For
further questions on feature and usage, please contact us at (852) 31884492 or (1)
415373 6020
Environmental Re uirements
Storage temperature: 32˚ to 113˚F (0˚ to 45˚C)
Operating temperature: 32˚ to 113˚F (0˚ to 45˚C)
www zetta com hk
version: 1 2
