Zetta Z86 User manual

Zetta Z86 Security Camera Quick Start Guide
Overview
Congratulations on your purchase of Zetta Z86 security camera!
Zetta Z86 is an intelligent security camera with low power motion detection function, work
being glass The camera comes with a built-in rechargeable battery which can record up to 9
hours continuous video and audio during typical use and standby for more than 25 days
when motion triggering (in max battery mode) is enabled By plugging in a 5V DC adapter
(not included), it can achieve max 156 hours circular recording for surveillance on a 256GB
microSD card *
* Actual life and performance may vary depending on usage and settings; battery not replaceable
Features
Circular recording
Time stamp – put time stamp on video
Motion-triggered recording – select to record only when motion is detected, 25 days
standby (in max battery mode), work through windows
Clouding push notification – can config to connect to the cloud server
and get push notification when an image is uploaded
Full HD 1080p resolution
Configura le video quality – high / medium / low
Support max 256GB microSD(TF) card (for better performance, use card larger than
8GB, class 4 or above, and before use, format the card to FAT32 format only)
Package Contents
Please unpack your intelligent security camera and check that the following are included:
Zetta Z86 security camera
USB 2 0 Cable
Quick Start Guide
Note: The PC configuration tool “Camera Widget” is not included in the package,
Z86 drawing
Charging
The camera comes with an internal rechargeable battery To use the camera for the first
time or not using the camera for a long time, please fully charge the battery for at least 8
hours and resync the time by using the Camera Widget (see section “PC Configuration Tool”)
You can charge your camera through the USB port of your computer, or a portable power
bank, or a 5V DC adapter or car charger
To charge the battery through USB port, connect the USB cable to the USB port of the
computer and the camera For details, please see the status below The camera will
function as a mass storage device, you will not be able to record video at this moment
To charge the battery through power bank, DC adapter or car charger, connect the charger
to the camera For details, please see the status below You will be able to record video
while charging, depending on the mode you set
Recording
The power key is located by the side of the camera It can turn the camera on or off
Start Recording
Insert a FAT32-formatted microSD card (please see “Format Card” on how to format the
card) Press and hold the Power key until the green LED is on (approximately 3 seconds),
and then release the key When you see the green LED flashing, the camera is recording
Otherwise, please see the status below
Stop Recording
Press and hold the Power key until the orange LED is off (for approximately 3 seconds)
WARNING: Turn off the camera efore removing the microSD card!
If the camera hangs, please use a pin to press the RESET key for 1 second to reset
it. The time will e lost. Please use the Camera Widget to sync the time again.
Status
Without external charger
Green LED on: camera is booting up
Green LED flashing: normal recording
Green / Red LED intermittent flashing: battery low and recording
Red LED on: no card, card fail, battery low or card full (not in circular recording)
Red LED flashing: cannot connect to router (when configured to connect to cloud server)
Connecting to an external charger
Orange LED on: charging but no recording
Green LED on: charging completed but no recording
Green LED flashing: charging completed and recording
Green / Orange LED intermittent flashing: charging and recording
Red LED on: no card, card fail or card full (not in circular recording)
Red LED flashing: cannot connect to router (when configured to connect to cloud server)
Connecting to computer
Orange LED on: charging
Green LED on: charging completed
power LED microSD USB
motion main
sensor camera mic
reset format /
upgrade
SpyGadgets.no
–loop back recording once memory card is full
please download it from https://spygadgets.no/minikamera-zetta-z86

Zetta Z86 Security Camera Quick Start Guide
Customize setting
For custom mode configuration, please use the PC configuration tool “Camera Widget”
Custom (default)
Video Quality* (High) / Medium / Low
Indoor Lighting (50Hz) / 60Hz
Condition
Orientation (Normal) / Up-side-down
Timestamp (Enable) / Disable
Circular Recording (Enable) / Disable
Frame rate (fps) (30) / 15
Mic (Enable) / Disable
LED On/Off (On) / Off
Motion-Trigger High / Medium / Low / (Disable)
Sensitivity**
Power Option*** Always On / (Max Battery)
*Memory usage:
Video Quality High: 3G / hour
Video Quality Medium: 2G / hour
Video Quality Low: 1.5G / hour
** If triggering is enabled, the Z86 will record for 10 seconds after powering up. Then it will go into
standby. If there is trigger, it will keep recording until there are no further triggers. After that, it
will record for 1 more minute and then standby again. If triggering is disabled, the Z86 will always
record.
*** When Always On is selected, Z86 will not record but the system will remain on. There will be 1
second delay in the recording after triggering. When Max attery is selected, the system will standby and
there will 4 seconds delay in the recording after triggering. Please choose Max attery if you need the
longest standby time.
Format card
For card >=64GB, it must be formatted to FAT32 before use
To format a card, please follow this:
1 Insert the card into Z86
2 Connect Z86 to a power bank or micro USB charger (not included) until orange light is on
4 Release the upgrade key
5 Press and hold the upgrade key again until the green light is flashing
6 Disconnect the USB charger or power bank, the format is completed
Manufacturer
Zetta Systems Limited
PC Configuration Tool (Camera Widget)
To synchronize the time and customize settings, download the PC configuration tool
REMARK: If the time shown is year 2030 or after due to loss of Real Time Clock,
please use the widget to sync the time. The files with incorrect time stamp will e
moved to the ZETTA_ERR folder. Please delete the files if they are not needed.
Minimum System Requirements
Windows XP, Vista, 7, 8, 10
Mac OS 10 9 or above
USB 2 0 port for hi-speed transfers and charging
Connecting to computer
To connect the camera to your computer, follow these instructions:
1 Connect the larger end of USB cable to an available USB port of the computer
2 Connect the smaller end of the cable to the USB port of the camera
3 The camera will appear in My Computer as a removable drive
App (Cam Server)
The Z86 also supports cloud push notification, please install the app "Cam Server" on Android
or iOS devices Please search with quotes in the Play or App store for better result
1 Connect the Z86 to a computer and use the Camera Widget software to enable wifi
2 Safely eject the drives and turn on Z86
3 Turn on phone wifi and connect to ZETTA_Z86
4 The default password is dvrdvrdvr
5 When asked, please choose "stay with wifi" or "always connect" and disable smart
switching If not ok, please do "forget network" in wifi setting and restart the phone and try
again
6 Run the app "Cam Server" on the phone and press the '+' to configure the camera
7 You can do local preview (no sound), browse microSD card file list or change settings
through the app when the camera and the phone are connecting to the same router The
camera will upload a 20-second image clip to the cloud server every hour if trigger is
disabled, or upload to the cloud server when it is first motion-triggered You will get a push
notification when your phone has Internet access and you can use the app to watch the
image clip (no sound) Please see the help message in the app for the usage
8 To restore to factory default, please turn on the camera, then use a pin to press the
upgrade key for 5 seconds and then release the key
Technical Support
Environmental Requirements
Storage temperature: 32˚ to 113˚F (0˚ to 45˚C)
Operating temperature: 32˚ to 113˚F (0˚ to 45˚C)
version: 1 3
to change the settings.
3. Use apin to press and hold the upgrade key until the red light is flashing
(Camera Widget) from spygadgets.no and follow the instruction in the software guide.
Before contacting us, please visit https://spygadgets.no/minikamera-zetta-z86
SpyGadgets.no