Zico ZI-9530 User manual

www.zicotech.com
ZI-9530 Temperature and Humidity data logger Manual
Product overview:
1. Sensor
2. Alarm indicator, red/green LED inside.
: green LED flashing，: Red LED flashing.
3. Electronic function key
4. Mechanical switch, hold down the switch, then pull out the shell.
5. USB protecting hood. Connect PC software
then you can setting up the data logger.
Replace battery
Simple start:
①Check the battery indicator is normal.
②Connect the USB data logger to the Windows PC. The first time using, according to the
computer instructions, install the system’s own driver. Similar to A new U disk.
③Setting the data logger. Please check the software CD，use the PC software setting the data
logger. For more information, please refer to the PC software help document.
④Recording and download data.
First step：Open the software. Then open the setting window.
CR2450
Battery
Hold down the switch,
then pull out the shell.

Second step:refer to the picture.
Third step:
Long Press
After Setting
"Manual"mode
Waiting start Recording

Fourth step: After recording some data, you can use the PC software download data.
Sample rate is 1minute, 10 minutes is ten data.
Sample rate & Record time
Sample rate
/min
Record time
/day
Sample rate
/min
Record time
/day
1
13.9
8
111.2
2
27.8
9
125.1
3
41.7
10
139.0
4
55.6
15
208.4
5
69.5
20
277.9
6
83.4
25
347.4
7
97.3
27
375.2
LCD display and button
2
5
7
3
1
6
4
8

Display:
①...Alarm indicator
②... Battery indicator
③... Record indicator
④... Humidity unit
⑤... Humidity reading
⑥...Temperature unit
⑦...Temperature reading
⑧...Function indicator
Buttons:
①down key
②replace battery
③enter key
1. Alarm indicator
Measurement values are within programmed limits. Green LED is flashing.
Measurement exceeded the programmed limits. If activated during programming a red LED
is flashing.
2. Battery indicator
Full battery
Battery OK
Low battery
Empty battery, replace
1
3
2

3. Recording indicators
The current state of the recording is indicated by the following symbols:
Recording paused
Recording stopped
Recording started
Appear after setting
State 1:
The logger is in the “Manual ”mode, but the start key has
not been not pressed yet.
State 3：
long press enter
The logger is recording.
State 4:
Recording is stopped.
long press enter

Function Menu
If the logger is not recording, only Start Recording is available.
Press the button to enter the function menu and to display humidity or air pressure, and
select the menu functions.
To activate a user menu function press the button and hold it for three seconds.
1.Start Recording
To start the recording if the logger is in “Manual”mode.
long press enter
2.Stop Recording
In recording state , Press the button to select this function to stop recording. Press button
and hold it for three seconds.
long press enter
3.Remaining Recording Time
Shows the remaining time until end of recording.
4.Max
Short press button switch Shows the highest reading since start of recording.

short/long press
enter
5.Min
6.Short press button switch Shows the lowest reading since start of recording.
short/long press
enter
Generating a PDF-File
As soon as the logger is connected to a USB-slot, a PDF file with all recorded data in chart and an
overview of alarms is generated automatically. During PDF generation “USB PDF”appears on the
display, green and red led light indicator, when the PDF file is ready “PDF”disappear and
remaining “USB”on the display.
Depending on the number of stored measurements, generating the PDF-file might take up to
30 seconds.
As soon as the logger is reprogrammed, the PDF file on the logger will be deleted.
LED Status Guide
LED Indication
Action
Cycle green single flash
-Logging
Cycle red single flash
-Logging, low alarm or high alarm.
-Manual mode waiting start
-Memory full
-Stop upon key
Green double flash one time
-Setup successful
-check upgrade file successful

Specification （T = 25℃unless otherwise noted）
Relative
Humidity
Overall Range
0 to 100%
Accuracy (0 to 20 and 80 to 100%)
±5.0%
Accuracy (20 to 40 and 60 to 80%)
±3.5%
Accuracy (40 to 60%)
±3.0%
resolution
0.1
Temperature
Overall Range
-30 to 60℃（-22 to 140℉）
Accuracy(-30 to +0℃,-22 to 32℉）
±1℃,±1.8℉
Accuracy（0 to 60℃,32 to 140℉）
±0.5℃,±0.9℉
resolution
0.1
Display
condition
-30~60℃
model
type
Data memory
Sample rate
ZI-9530
Temperature and Humidity
20010
1min~24h
Remark:
CR2450 battery performance is optimal in room temperature. Battery life cycle will reduce at low
temperature (-18℃). If the device is to be used to record in extremely low temperature, it is
advised to take measures to reduce power consumption to prolong operation time. An option
includes:
Choose battery that is designed to operate at low temperature
Disable LED to reduce power consumption
Set longer sample interval, 5 minutes for example
Firmware upgrade
long press enter
User can also upgrade its firmware in this page.
In this page, long press and display will show “UP+USB”
Then insert the device into the PC USB port. The device will appear as a Mass Storage Device in
PC with no content.
Drag and drop the firmware to the folder.
The device will disappear in the OS. DO NOT unplug the device from PC. It takes around
After upgrade completed, Device will automatically appear as a Mass Storage Device again.
The firmware version is indicated in the left bottom corner of the .pdf test report generated.

Restore Default factory firmware
Remove the battery, in the following order:
1. Hold down the button (until power on) ; connect to the computer USB, the green
LED light up.
2. Waiting for 2 minutes, computer will identify the instrument USB disk.
Delete all data
1. Logger work normally on battery power. Hold down two buttons , connect to the
computer USB, the logger will delete all data.
*If waiting for 5 minutes and the instrument can’t connect to the computer, maybe need to restore
default factory firmware, or need to delete all data.