ZIGBEE Vismart VGZ-SS17 User manual

INTRODUCTION
TECHNICAL PROPERTIES
INSTALLATION AND BATTERY REPLACEMENT
DC3V (CR17450 / 3.0 V baery)
Voltage:
≤3uA
≥85dB(1m)
Zigbee Connecon Range
Alarm Sound:
≤25mA
Standby Current:
Operang Current:
≤150m (open space)
Zigbee Control
Alarm System
V-ZigBee Control Smart Home Systems
VGZ-SS17
SMOKE DETECTOR
USER MANUAL
Smoke detectors are crucial for the safety of you and your property.
Though, tradional smoke detectors warn you only if you are at home. With
our wireless smoke detector you don't have to worry about not being in
your home. If anything bad happens, security system will immediately warn
you via the mobile applicaon while triggering the alarm.
System Parameters
Dimensions
Zigbee Wireless
Standarts
IEEE 802.15.4
116mm
116mm 42mm
Operang Humidity:
MAX 95%RH
Operang Temperature:
-10°C~50°C
Dimensions:
116x1116x42mm
Sengs Buon &
LED Display
Speaker
Baery Slot
Alarm Mode: Sound and Light Alarm
Alarm Value:
3.0%bs

Seng Up the Smoke Detector:
Remove the front cover by pulling as shown in the image above. Remove the insulator
of the baery to power the detector and close back the cover. Press the Sengs
Buon once to acvate the smoke detector.
Note: Install the smoke detector away from possible smoky places (cooking hob, oven
etc).
Smoke sensor has two different indicator, a green light and a red light.
Red Light Meanings:
1. In the User Mode; Red light flashing rapidly or illuminang connuously indicates
that alarm is triggered.
Green Light Meanings:
INSTRUCTIONS
1. In the User Mode; Green light blinking shows that device is working normally.
2. In the User Mode; If you press and hold the Sengs Buon green light will
illuminate connuously indicang that device is in Sengs Mode.
3. In the Sengs Mode; Flashing 5 mes indicates that a wrong buon input or
wrong command have entered.
4. In the Sengs Mode; Flashing 2 mes indicates that the entered command was
successful.
5. In the Sengs Mode; Flashing rapidly indicates that a network connecon is being
made. Green light will flash 3 mes aer connecon made successfully.
Red and Green Light Illuminang Together:
1. If the device is not connected or disconnected from network green and red light will
flash 3 mes simultaneously.
2 To test if the device is working normal or not press the Sengs Buon once. If the
red light flashes 3 mes and alarm sounds 3 mes, that indicates alarm is armed and
working normally.
LED LIGHT CODES
CONTACT
Network Connecons:
Press and hold the Sengs Buon ll the green light illuminates connuously. When
the green light turns on press the buon once(green light will flash once aer
pressing the buon).
Press and hold the buon again ll the green light turns on. Once the device starts
searching for the network the green light will start flashing rapidly and when the
connecon has been made green light will flash 3 mes.
Note: Before connecng this device, network connecon mode should be acvated
on the Gateway by using the Sengs Buon on it.
Factory Sengs:
Press the Sengs Buon for 3 seconds ll the green lights illuminates connuously.
Then press and release the Sengs Buon 10 mes(green light will flash once aer
each pressing). Press and hold the Sengs Buon for 3 seconds. Green light will flash
3 mes indicang that device is successfully returned to factory sengs.
Note: If you press the Sengs Buon more or less than 10 mes green light will flash
55 mes indicang that the process was unsuccessful. You can connue the process by
pressing 10 mes as explained above.
Note: You have to set the network sengs aer returning back to factory sengs.
SHENZHEN VIDEOCOM ELECTRONICS TECHNOLOGY CO.LTD.
5th.Floor East 2nd.Building, Peng Teng Da Industrial Park,
HuarongRd.Longhua, Bao an District Shenzhen CHINA
VIDEOCOM ELEKTRONIK VE BILGISAYAR SISTEMLERI A.S.
Ivedik OSB 1419.Cad. No:72 06370 Y.Mahalle Ankara TURKIYE
VIDEOCOM-UK ELECTRONICS AND SOFTWARE LTD.
Unit 2, Little Britain House, Alma Road, Chesham,
Buckinghamshire, HP5 3HB London, United Kingdom
Headquarter
Distributor
Factory