Zone MJOLNIR User manual

USER MANUAL (ENG)
MJOLNIR
THOR ZONE

1MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
4X M3x4
1X LED-TO-MOTHERBOARD CABLE (4-PIN)
1X LED-TO-MOTHERBOARD CABLE (3-PIN)
1X LED-TO-LED CABLE
2X RGB LED STRIPS
MJOLNIR R — GODRAYS
8X M3x48X #6-32x1/4 PAN HEAD8X #6-32x1/4 COUNTERSUNK
SCREWS
2X PANELS SETS
OR
2X TEMPERED GLASS PANELS
OR
2X PERFORMANCE PANELS
PANELS
MJOLNIR BASE MODEL
WHAT’S IN THE BOX?

2MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
1. Unlock the case by turning the lock knob counterclockwise (located on the back) TIP: Use a credit card to easier turn the lock knob
2. Place the case on it’s back (hold the back panel so the Core doesn’t slide out) TIP: Put a soft cloth underneath to avoid scratches
3. Gently pull the Shell up and off the Core
4. Perform steps 1-3 in reverse when closing the case again
INSTRUCTIONS
SCREWSTOOLS
OPEN THE CASE

3MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
FLIPPEDNORMAL
•The Core can be inserted normally or reversed 180° NOTE: Reversed orientation benefits thermals when using water coolers
INSTRUCTIONS
SCREWSTOOLS
FLIP LAYOUT

4MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
•Push on the panel (using one hand) from the inside until it releases TIP: Hold the panel with your other hand when it releases
INSTRUCTIONS
SCREWSTOOLS
CHANGE PANELS

5MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
+5V
D
GND
LED-TO-MOTHERBOARD CABLE (4-PIN)
OR
+5V
D
GND
LED-TO-MOTHERBOARD CABLE (3-PIN)
IN
1Attach the LED strips to the Core with four M3x4 screws
2. Connect the LED strips to each other, use the LED-to-LED cable NOTE: Connect the IN-port on one LED strip to the OUT-port on the other
3. Connect the LED strips to the Motherboard, use the LED-to-Motherboard cable NOTE: Connect the IN-port on the LED strips to a 5V dRGB header
•There are 2 available LED-to-Motherboard cables (3-pin and 4-pin) TIP: Use one that best fits your motherboard’s 5V dRGB header
•5V DIGITAL ONLY - AVOID 12V/ANALOG HEADERS AT ALL COSTS!
•CORRECTLY CONNECT POWER, DATA AND GROUND!
INSTRUCTIONS
4x M3x4
SCREWS
•Hex key (size: H2.0)
TOOLS
MJOLNIR R — GODRAYS

6MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
1. Install the I/O shield (usually included with your motherboard)
2. Align the motherboard with the I/O shield and secure it with four #6-32x1/4 Pan Head screws
3. Connect the PCIe riser
4. Connect the power button
INSTRUCTIONS
4x #6-32x1/4 Pan Head
SCREWS
•Phillips screw driver (size: PH1)
TOOLS
HARDWARE — MOTHERBOARD

7MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
1. Loosen the GPU bracket screw and slide the backet up
2. Insert the GPU into the PCIe riser
3. Slide the GPU bracket back down and tighten the screw again
INSTRUCTIONS
SCREWS
•Hex key (size: H2.0)
TOOLS
HARDWARE — GRAPHICS CARD

8MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
1. Attach the PSU to the PSU bracket and secure it with four #6-32x1/4 Pan Head screws
2. Plug in the power cable into the PSU power socket
INSTRUCTIONS
4x #6-32x1/4 Pan Head
SCREWS
•Phillips screw driver (size: PH1)
TOOLS
HARDWARE — POWER SUPPLY (1/2)

9MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
1. Remove the PSU frame and reattach in the bottom position
2. Attach the PSU to the PSU bracket and secure it with four #6-32x1/4 Pan Head screws
3. Plug in the power cable into the PSU power socket
INSTRUCTIONS
4x #6-32x1/4 Pan Head
SCREWS
•Phillips screw driver (size: PH1)
TOOLS
HARDWARE — POWER SUPPLY (2/2)

10MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
•Fans, radiators and AIO water coolers can be mounted to the bottom rails using 4-8 #6-32x1/4 Countersunk screws
INSTRUCTIONS
4-8x #6-32x1/4 Countersunk
SCREWS
•Phillips screw driver (size: PH1)
TOOLS
HARDWARE — FANS AND RADIATORS

11MJOLNIR
S:t Persgatan 23, 602 33 Norrköping Sweden
[email protected] thor-zone.com
THOR ZONE
•Attach 1-2x 2.5in SSDs to the storage frame and secure them with 4-8 M3x4 screws
INSTRUCTIONS
4-8x M3x4
SCREWS
•Hex key (size: H2.0)
TOOLS
HARDWARE — SSDs AND STORAGE