Zonet ZEW1502 User manual

WirelessNetworkAdapter Usermanual
Wireless Network Adapter
User Manual
Page 1

WirelessNetworkAdapter Usermanual
Table of Contents
Chapter 1 Introduction...................................................................... 3
1.1 Welcome ..............................................................................................................................3
1.2 About This Guide..............................................................................................................3
1.3 Copyright statement........................................................................................................3
1.4 Contents of Package........................................................................................................4
1.5 Before you begin...............................................................................................................4
Chapter 2 Designing Your Wireless Network ..................................... 4
2.1 Cardbus adapter ...............................................................................................................4
2.2 PCI adapter.........................................................................................................................5
2.3 USB adapter .......................................................................................................................5
Chapter 3 Install Wireless Adapter.................................................... 6
3.1 Install Driver and Utility.................................................................................................6
3.2 Install Adapter...................................................................................................................8
3.3 Configuration your wireless adapter....................................................................... 11
Chapter 4 Using the Wireless Client Configuration Utility................ 12
4.1 Network Status................................................................................................................13
4.2 Site Survey .......................................................................................................................14
4.3 Admin..................................................................................................................................15
4.4 Profile Manager................................................................................................................18
Chapter 5 Troubleshooting .............................................................. 22
APPENDIX A Specifications.............................................................. 24
Page 2

WirelessNetworkAdapter Usermanual
Chapter 1 Introduction
1.1 Welcome
The Wireless Network Adapter is a powerful 32-bit Cardbus/PCI/USB Adapter
that installs quickly and easily into PCs. The Adapter can be used in Ad-Hoc
mode to connect directly with other cards for peer-to-peer file sharing or in
Infrastructure mode to connect with a wireless access point or router for access
to the Internet in your office or home network.
The Wireless Cardbus/PCI/USB Adapter connects you with 802.11g networks at
up to an incredible 54Mbps! And for added versatility, it can also interoperate
with all the up to 11Mbps 802.11b products found in homes, businesses, and
public wireless hotspots around the country. And in either mode, your wireless
communications are protected by industrial-strength WPA, so your data stays
secure.
1.2 About This Guide
This User Manual contains information on how to install and configure your
Wireless Adapter to get your network started accessing the Internet. It will
guide you through the correct configuration steps to get your device up and
running.
Note and Caution in this manual are highlighted with graphics as below to
indicate important information.
Contains related information corresponds to a topic.
Necessary steps, actions or messages should not be ignored.
1.3 Copyright statement
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise without the prior writing of the
publisher.
Page 3

WirelessNetworkAdapter Usermanual
1.4 Contents of Package
 Wireless network Cardbus/PCI/USB adapter
 Manual, Drivers and Utility on CD
 Quick Installation Guide
If any of the above items are missing, please contact your reseller.
1.5 Before you begin
You must have at least the following:
 A laptop computer/desktop PC with an available 32-bit Cardbus/PCI/USB
slot
 At least a 300MHz processor and 32MB of memory
 Windows 98SE, ME, 2000, XP, Vista
 A CD-ROM Drive
 Cardbus/PCI/USB controller properly installed and working in the laptop
computer
 A 802.11g or 802.11b Access Point (for infrastructure Mode) or another
802.11g or 802.11b wireless adapter (for Ad-Hoc; Peer-to-Peer networking
mode.)
Chapter 2 Designing Your Wireless Network
The wireless Cardbus/PCI/USB Adapter supports up to 54 Mbps connections.
This card is fully compliant with the specifications defined in IEEE802.11g
standard. It is designed to complement PCI Local Bus computers and supports
Windows 98SE/Me/2000/XP/Vista.
2.1 Cardbus adapter
Figure 2-1
Page 4

WirelessNetworkAdapter Usermanual
The two status LED indicators of the Cardbus wireless adapter are described in
the following.
 PWR ON (Green): Indicates the Adapter is ready
 Lnk/Act ON (Green): Indicates a valid connection
 Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
2.2 PCI adapter
Figure 2-2
The status LED indicators of the PCI wireless adapter are described in the
following.
 Lnk/Act ON (Green): Indicates a valid connection
 Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
2.3 USB adapter
The status LED indicators of the USB wireless adapter are described in the
following.
 Lnk/Act ON (Green): Indicates a valid connection
 Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
Figure 2-3
Page 5

WirelessNetworkAdapter Usermanual
Chapter 3 Install Wireless Adapter
3.1 Install Driver and Utility
 Insert the Driver and Utility CD-ROM into the CD-ROM driver.
 The Wizard should run automatically, and Figure 2-1 should appear. If it
dose not, click the Start button and choose Run. In the field that appears,
enter D:\autorun.exe (if ‘’D’’ is the letter of your CD-ROM drive).
Figure 2-1
 Click Install Driver & Utility on the Wireless Client Configuration Utility
screen.
Page 6

WirelessNetworkAdapter Usermanual
Figure 2-2
 Follow the Install Shield Wizard steps, and click Finish when done.
Figure 2-3
 Now turn off your PC or notebook
Page 7

WirelessNetworkAdapter Usermanual
3.2 Install Adapter
3.2.1 Cardbus Adapter
 Power on your notebook, let the operating system boot up completely, and
log in as needed.
 Hold the adapter with the LOGO facing up and insert it into a Cardbus slot.
Figure 3-1
 If the Found New Hardware Wizard displays, choose Install the software
automatically (Recommended), and click Next button. The driver will
be installed automatically.
Page 8

WirelessNetworkAdapter Usermanual
Figure 3-2
3.2.2 PCI Adapter
 Open your PC case and locate an available PCI on the motherboard.
 Slide the PCI Adapter into the PCI slot. Make sure that all of its pins are
touching the slot’s contacts. You may have to apply a bit of pressure to slide
the adapter all the way in. after the adapter is firmly in place, secure its
fastening tab to your PC’s chassis with a mounting screw. Then close your
PC.
 Attach the external antenna to the adapter’s antenna port.
 Power on the PC.
Page 9

WirelessNetworkAdapter Usermanual
Figure 3-3
 If the Found New Hardware Wizard displays, choose install the software
automatically (Recommended), and click Next button. The driver will
be installed automatically.
3.2.3 USB Adapter
 Power on your PC, let the operating system boot up completely, and log in
as needed.
 Hold the adapter and insert it into a USB slot.
 If the Found New Hardware Wizard displays, choose install the software
automatically (Recommended), and click Next button. The driver will
be installed automatically.
Figure 3-4
You have now completed the driver and hardware installation for the Adapter.
Page 10

WirelessNetworkAdapter Usermanual
3.3 Configuration your wireless adapter
 The Wireless Client Configuration Utility screen will appear automatically.
Figure 4-1
 Click the Site Survey tab then click the Refresh button to search for
available wireless networks.
Page 11

WirelessNetworkAdapter Usermanual
Figure 4-2
 To connect to one of the networks on the list, select the wireless network,
and click Associate button.
Chapter 4 Using the Wireless Client
Configuration Utility
Use the Wireless Client Configuration Utility to check the link information,
search for available wireless networks, or create profiles that hold different
configuration settings. You can double-click the icon on your system desktop
start it. Another way to start the Configuration Utility is to click on
Start>Programs>Wireless Client Configuration Utility>WirelessCfg.
If you are using Windows XP, you can use either the Zero Configuration Utility or
the Wireless Client Configuration
Page 12

WirelessNetworkAdapter Usermanual
4.1 Network Status
The Network Status tab displays signal strength and link information, Internet
Protocol (TCP/IP).
Figure 4-1
Link Information
Status: The status of the wireless network connection.
 Network SSID: The unique name of the wireless network.
 Network Type: The mode of the wireless network currently in use.
 Network BSSID: The MAC address of the wireless network’s access
point.
 Security: The status of the encryption security feature.
 Link Speed: The data transfer rate of the current connection.
 Channel: The channel to which the wireless network devices are set.
Internet Protocol (TCP/IP)
 DHCP Option: The status of the DHCP client.
 IP Address: The IP Address of the Adapter.
 Subnet Mask: The Subnet Mask of the Adapter.
 Default Gateway: The Default Gateway address of the Adapter.
Page 13

WirelessNetworkAdapter Usermanual
4.2 Site Survey
The Site Survey tab, displays a list of infrastructure and ad-hoc networks
available for connection.
Figure 4-2
The section of the window displays the Available Networks. Highlight the
network to which you wish to connect. Click on the Associate button.
Page 14

WirelessNetworkAdapter Usermanual
Figure 4-3
Choose the Authorization modes and Encryption modes in the drop-down box.
If the wireless network uses a Passphrase, enter the Passphrase in the
Passphrase field. If the wireless network uses a WEP key, enter the WEP key in
the Key field.
Click the OK button to complete the network connection and return to the Site
Survey screen, or click the Cancel button the cancel the network connection
and return to the Site Survey screen.
4.3 Admin
The Admin tab screen lets you import or export profiles.
Page 15

WirelessNetworkAdapter Usermanual
Figure 4-4
 Export Profile
To save the profile(s) in a different location, click the Export Profile button. On
the screen that appear , direct Windows to the appropriate folder and click the
OK button.
Page 16

WirelessNetworkAdapter Usermanual
Figure 4-5
 Import profile
Click the Import Profile button to import a profile that has been saved in
another location. From the screen that appears, select the appropriate file, and
click the Open button.
Figure 4-6
Page 17

WirelessNetworkAdapter Usermanual
4.4 Profile Manager
Figure 4-7
On the Profile Manager tab, click the Create button to create a new profile.
Page 18

WirelessNetworkAdapter Usermanual
Figure 4-8
When the Network Info screen appears (Figure 6-8), enter a name for the new
profile. Enter the Network SSID. Choose the Infrastructure Mode in the Network
Type drop-down box if you want your wireless computers to communicate with
computers on your wired network via a wireless access point. Choose the
Ad-Hoc Mode in the Network Type drop-down box if you want multiple wireless
computers to communicate directly with each other. Click the Next button to
continue or the Back button to return to the previous screen.
 Ad-Hoc Mode
If you choose Ad-Hoc Mode, select the Wireless Mode from the drop-down
menu. Then, select the correct operating channel for your network form the
Prefer Channel drop-down menu. Click the Next button.
Page 19

WirelessNetworkAdapter Usermanual
Figure 4-9
 Infrastructure Mode
If you choose Infrastructure Mode, click the Next button.
Page 20