ZoneVu ZVK-007 User manual

SECURITY with VISION
ZVK-007 Keyboard
USERS MANUAL

MEYERTECH LIMITED ISSUE 09
Page 2 http://www.meyertech.co.uk MAN-007
CONTENTS
1. Installation 5
1.1 EQUIPMENT 5
1.2 CONNECTING THE ZVK-007 TO THE ZoneVu NETWORK 5
1.3 KEYBOARD ADDRESS 5
1.4 SERIAL COMMUNICATIONS 5
2. GETTING STARTED 6
2.1 POWER-UP MESSAGES 6
2.2 LOGGING ON 6
2.3 MODE SELECTION 7
3. CLASIK MODE 7
3.1 CLASIK MODE FACILITIES 7
3.2 SELECTING A CAMERA 8
3.3 SELECTING A MONITOR 8
3.4 CAMERA CONTROL 8
3.5 RELEASING CAMERA CONTROL 9
3.6 SALVO SEQUENCE 9
3.7 PLACING A MONITOR INTO SEQUENCE MODE 9
3.8 GLOBAL FACILITY 10
3.9 PRESET FACILITY 10
3.10 PATROL FACILITY 10
3.11 LATCHED CAMERA FUNCTIONS 11
3.11.1 FUNCTION TIMEOUT OVERIDE 11
3.12 ZONAL SWITCHING 11
3.12.1 SELECTING ZONES 12
4. Site Mode 12
4.1 SITE MODE FACILITIES 12
4.2 SELECTING A SITE 12

MEYERTECH LIMITED ISSUE 09
4.3 SELECTING A TRUNK 13
4.4 SELECTING A CAMERA 13
4.5 SELECTING A MONITOR 14
5. PCI MODE 14
5.1 PCI MODE FACILITIES 14
6. SUPERVISOR LEVEL 14
6.1 SUPERVISOR LEVEL FEATURES 14
6.2 SELECTING AN OPTION 15
6.3 PASSWORDS 15
6.3.1 CHANGING A PASSWORD 15
6.4 MODE ACCESS 16
6.5 KEYBOARD SET-UP 16
6.5.1 KEYBOARD CAMERA ACCESS 17
6.5.2 KEYBOARD MONITOR ACCESS 17
6.5.3 KEYBOARD ENGINEERING FACILITIES 18
6.5.4 ZONE SETUP 18
6.6 FEATURE ACCESS 19
6.7 ZVR CONFIGURATION 20
6.8 CAMERA CONFIGURATION 21
6.9 ZVM-CONFIGURATION 22
7. VCR MODE 23
7.1 SELECTING A VCR 23
8. MUX MODE 24
8.1 SELECTING A MULTIPLEXER 24
9. TROUBLE SHOOTING GUIDE 25
10. DECLARATION OF CONFORMITY 26
11. Product Warranty 27
12. DOCUMENT HISTORY 28
Page 3http://www.meyertech.co.ukMAN-007

MEYERTECH LIMITED ISSUE 09
Whilst every effort has been made to confirm the information in this document is correct,
MEYERTECH LIMITED cannot accept any liability for any errors, omissions and or incorrect
information contained within this document.
No part of this document may be reproduced or distributed in any form or by any means
without prior written consent from MEYERTECH LIMITED
MEYERTECH LIMITED are committed to continuous product development and therefore reserve
the right to change specifications without notice.
©1997-2004 ALL RIGHTS RESERVED.
Page 4 http://www.meyertech.co.uk MAN-007

MEYERTECH LIMITED ISSUE 09
1. INSTALLATION
1.1 EQUIPMENT
The ZVK-007 should be carefully unpacked and the contents checked against the list below.
ZVK-007 KEYBOARD (19 Inch By 4U Panel Mounted)
MAINS CUBE PSU.
ZoneVu NETWORK NODE BOX
1.2 CONNECTING THE ZVK-007 TO THE ZONEVU NETWORK
STEP 1 Wire the Mains Cube PSU to the Network Node box observing the
polarity. Set the PSU to give +12V output.
STEP 2 Wire the Network Node box to the ZoneVu Network observing the
polarity of the connections and ensuring that the screen of the Network
cable is connected to the PSU 0V connection.
STEP 3 Plug the Mains Cube into a convenient power socket.
STEP 4 Plug the ZVK-007 into the FCC connector on the Network Node box.
1.3 KEYBOARD ADDRESS
Each keyboard connected to the ZoneVu network requires a unique Module Access Code (MAC) to
function correctly. Set the MAC by following the procedure in Section 6.5.3.
NOTE ! The MIC (Module Identification Code) is not used by the ZVK-007 and can be ignored.
1.4 SERIAL COMMUNICATIONS
The ZVK-007 can operates on a RS422 Topology with the following parameters -
BAUD RATE - 9600 / 19200 / 38400 STOP BITS - 1
DATA BITS - 8 FRAME - 10 BIT
PARITY - NONE FLOW - NONE
Page 5http://www.meyertech.co.ukMAN-007

MEYERTECH LIMITED ISSUE 09
Page 6 http://www.meyertech.co.uk MAN-007
2. GETTING STARTED
2.1 POWER-UP MESSAGES
Whenever the keyboard is powered-up the following messages are displayed by the LCD. Examples
shown.
KEYBOARD MODEL AND COPYRIGHT
SOFTWARE VERSION - 4.21.0.0
RELEASE DATE - 13-05-04
MODULE ACCESS CODE - MAC 01
BAUD RATE - 9600 baud
PRIORITY -1
MODE - Matrix Mode
2.2 LOGGING ON
The ZVK-007 has four levels of access, three User levels and one Supervisor level and is fully LOG
ON / LOG OFF Password Protected.
USER LEVELS can be programmed to allow access to different modes e.g. - CLASIK and PCI.
Keyboard Configuration Management is carried out from the SUPERVISOR LEVEL. User Level
Access, Password allocation and Keyboard Set-up has to be carried out from this Level. Video Matrix
Configuration and Camera Receiver Configuration can also be carried out from this Level.
To protect the keyboard from unauthorized use the operator can LOG the keyboard off the System.
When the keyboard is in this state the display will show -
LOGGEDOFFPLEASEENTERPASSWORD
INFO The password can be alphanumeric and up to TEN Characters.
STEP 1 Type in the PASSWORD for the User Level you require access to.
INFO Use the SHIFT key to shift between the Alpha and Numeric Keys. A capital ‘A’ will
appear on the display whenever the numeric keypad is shifted to select alpha keys.
STEP 2 Press the ENT Key
INFO The Display will then either show ACCESS DENIED if the Password was incorrect or USER
LEVELifAccess to the User Level when the Password is correct.

MEYERTECH LIMITED ISSUE 09
2.3 MODE SELECTION
Once Logged On the display will show SELECTMODE
LOGOFF
STEP 1 Press the MODE key to cycle through the Modes available for this USER LEVEL.
INFO In sequence the display will show for example LOGOFF
CLASIKMODE
VCRMODE
STEP 2 Press ENT to select the Mode required.
3. CLASIK MODE
3.1 CLASIK MODE FACILITIES
MONITOR SELECTION - 1 - 64
CAMERA SELECTION - 0 - 512
GLOBAL - HOME - AUX1 - WIPE - IRIS AUTO - LAMP
PRESETS - HOME - 1 - 16
PATROL - ORDERED - RANDOM
CAMERA CONTROL - PAN & TILT - ZOOM, FOCUS, IRIS
- IRIS AUTO / MANUAL - AUX1, AUX2, LAMP
- PWI, WASH, WIPE
SALVO SEQUENCING - 1- 64 MONITORS 16 SEQUENCE PATTERNS STEP-BACK -STEP-
FORWARD PAUSE
When the Keyboard is in CLASIK MODE the display will show CLASIKMONITOR-n
MODECAMERA-n
Page 7http://www.meyertech.co.ukMAN-007

MEYERTECH LIMITED ISSUE 09
Page 8 http://www.meyertech.co.uk MAN-007
3.2 SELECTING A CAMERA
STEP 1 Using the Numeric Keypad enter the digits of the Camera Number to be selected.
INFO Each Digit entered will be displayed adjacent to CAMERA.
STEP2 Press the ENT Key.
INFO The display will then either retain the camera entered indicating a valid entry or show
CAMERA-ERROR or CAMERA-DENIED
To select another Camera repeat process from Step 1.
3.3 SELECTING A MONITOR
STEP 1 Press the MON key so the display shows MONITOR
STEP 2 Enter a monitor number using the Alpha Numeric Keypad.
INFO Each digit entered will be displayed adjacent to MONITOR.
STEP 3 Press the ENT Key
INFO The display will then either retain the Monitor entered indicating a valid entry or show
MONITOR-ERROR
or
MONITOR-DENIED
3.4 CAMERA CONTROL
The Camera shown on the display will always be the Camera under Control. If you require to control
a different Camera refer to section 3-2 Selecting a Camera.
Control of the Camera shown on the display is automatically achieved (assuming no other keyboard
with a higher or equal priority is already controlling the camera) when either the Pan & Tilt JOYSTICK
or Zoom & Focus JOYSTICK are moved or when either of the following keys are pressed -WASH -
AUX2 - PWI - PTZ.
To indicate control has been achieved the display will show PTZ
Otherwise the display will show CONTROL DENIED indicating the camera is currently under the control of
another keyboard.

MEYERTECH LIMITED ISSUE 09
3.5 RELEASING CAMERA CONTROL
The PTZ key when pressed will release control of the Camera, (so other keyboards can access it)
without having to select another Camera.
The second function of the PTZ key is to take control of a Camera without having to use the
JOYSTICKS etc.
Control of the Camera is also automatically released when either a new monitor or camera selection
mode, GLOBAL, PRESET or PATROL are selected.
3.6 SALVO SEQUENCE
Any Video Matrix monitor can be placed into SALVO Sequence Mode to display a sequence pattern
of cameras. Camera pictures are Salvo switched to maintain framing between patterns. When one or
more monitors have been assigned to run sequence patterns the STEP FORWARD - STEP BACK
and PAUSE keys can be used to control the SALVO switching.
STEP-BACK Each time the STEP BACK key is pressed all patterns are stepped back one
frame to display the previous camera picture.
STEP-FORWARD Each time the STEP FORWARD key is pressed all patterns are stepped
forward one frame to display the next camera picture in the pattern.
PAUSE Whilst the PAUSE key is held down all patterns will be displaying the current
camera pictures i.e. the salvo dwell time is temporarily suspended.
3.7 PLACING A MONITOR INTO SEQUENCE MODE
STEP 1 Press the SALVO key so the display shows CAMERA-P
STEP 2 Enter a PATTERN number using the Numeric Keypad in the
range 1 - 16
INFO Each digit entered will be displayed adjacent to CAMERA -P3
STEP 3 Press the ENT Key
INFO The display will then either retain the Pattern entered, indicating a valid entry, or show
CAMERA-Error and revert back to the current camera selected.
Page 9http://www.meyertech.co.ukMAN-007

MEYERTECH LIMITED ISSUE 09
Page 10 http://www.meyertech.co.uk MAN-007
3.8 GLOBAL FACILITY
The GLOBAL facility allows a number of camera functions to be activated on all cameras in the
system with a single keystroke. The global facility can be used with the following camera control
facilities.
WIPE - All camera wipers will be switched on or off
LAMP - All camera lamps will be switched on or off
AUX1 - All camera auxiliary 1 outputs will be switched on or off
IRIS - All cameras will revert to Auto-Iris
HOME - All cameras will return to their Home position
STEP 1 Press the GLOBAL key so the display shows GLOBAL
STEP 2 Press one of the above listed function keys
INFO Cameras currently under control from another keyboard will not have the function
activated.
3.9 PRESET FACILITY
The PRESET facility allows camera presets to be recalled in the range 1 - 16. HOME is a special
preset facility which has its own dedicated key.
STEP 1 Press the PRESET key so the display shows PRESET
STEP 2 Enter a PRESET number using the Numeric Keypad in the range 1 - 16
INFO Each digit entered will be displayed adjacent to PRESET -1
STEP 3 Press the ENT Key
3.10 PATROL FACILITY
The PATROL facility allows a camera patrol to be recalled in the range 1 - 2. The camera will
automatically patrol a number of presets on either a Random or Ordered basis.
PATROL 1 - RANDOM Patrol recalls presets randomly and dwells at each preset position for
random period of time up to 15 minutes.
PATROL 2 - ORDERED Patrol recalls presets in a ordered manner dwelling at each preset for a
pre-defined period of time.
STEP 1 Press the PATROL key so the display shows PATROL
STEP 2 Using the Numeric Keypad Press 1to select a Random patrol 2to select an Ordered
patrol.
INFO A camera will continue to Patrol until it receives any valid control command.