ZooZ ZSE42 800LR User manual

WATER LEAK XS SENSOR
ZSE42 800LR
www.getzooz.com
ŸQuick and reliable water leak
alerts sent to your Z-Wave hub
ŸNEW 800 series chip for faster
communication and more
battery life than ever
ŸExtra small to fit anywhere
ŸZ-Wave Long Range for ultra
reliable no-mesh communication
ŸThe latest S2 security and
SmartStart for secure set-up
ŸSupports OTA firmware updates
ŸSE42 800LRModel Number: Z
ŸPower: 1 x CR2450 battery
ŸOperating Temperature: 32° –
104° F
ŸRange: Up to 130 feet line of sight
(up to 1300  with Long Range)
ŸInstallation and Use: Indoor or
outdoor under eve (can’t be
exposed to direct rainfall or sun, a
little splash is OK)
ŸDimensions: 2.4” x 1.4” x 0.4”
FEATURES
SPECIFICATIONS
1. POWER THE SENSOR
Use the included round tool to
gently twist the battery cover to the
le and and access the battery.
Pull the tab from under the
battery to activate the sensor.
Close the cover with the same
round tool by twisting it gently to
the right.
The LED indicator on the front of
the sensor (top right corner) will
start blinking for around 10
seconds once the sensor is
powered.
The LED indicator doesn’t blink
or light up at all?
ŸMake sure the battery is
inserted correctly per the
positive / negative pole marks.
ŸTry a fresh lithium non-
rechargeable battery.
ŸClick the Z-Wave button 3
times as quickly as possible to
force inclusion/exclusion
mode in case you missed
when it first flashed.
S2
USER MANUAL
INSTALLATION
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the
app (or web interface). Not sure
how? [e-mail]
If you’re using an S2 hub, it will ask
you to enter the DSK PIN or scan
the QR code printed on the inside
of the back cover of the sensor to
complete SmartStart inclusion.
While the hub is looking for new
devices, click the Z-Wave button
3 times as quickly as possible.
The LED indicator will start
flashing to confirm inclusion
mode and turn off once inclusion
is completed.
Z-WAVE CONTROL
2. ACTIVATE the sensor
Hubitat
Get more tutorials and helpful tips at
ww.support.getzooz.com
Home Assistant
NEED SOME HELP?
[e-mail]
Choose your hub and scan the QR
code with your phone’s camera.
Then click on the link to access the
step-by-step pairing instructions.
TIP!
It’s best to add your sensor from
the area where it will be installed
so the hub can find the best route
to reach it right away.
The sensor won’t add to your
system? Try this:
1. Initiate EXCLUSION in your hub
and click the Z-Wave button 3
times as quickly as possible.
2. Click the Z-Wave button quicker
when adding it.
3. Bring the sensor closer to your
hub, it may be out of range.
4. Double-check if the device is
powered.
5. Get troubleshooting tips specific
to your hub at
www.support.getzooz.com
1. Bring the sensor within direct
range of your Z-Wave hub.
2. Put the Z-Wave hub into
exclusion mode (not sure how to
do that? [e-mail]).
3. Click the Z-Wave button 3 times
as quickly as possible.
4. Your hub will confirm exclusion
and the sensor will disappear
from your controller's device list.
When your network’s primary
controller is missing or otherwise
inoperable, you may need to reset
the device to factory settings
manually. In order to complete the
process, make sure the sensor is
powered, then click the Z-Wave
button twice and hold it the third
time for 10 seconds. The LED
indicator will blink continuously.
Immediately aer, click the Z-
Wave button twice more to
finalize the reset. The LED
indicator will flash 3 times to
confirm a successful reset.
NOTE: All previously recorded activity and
custom settings will be erased from the
device’s memory.
The sensor’s wake-up interval is set
to 12 hours by default to save
battery life. Use the Wake Up
Command Class to adjust the
interval. Click the Z-Wave button 4
times quickly to wake the sensor
up manually. The LED indicator will
flash once to confirm the device is
awake. During wake-up, the sensor
turns the Z-Wave radio on for one
minute to receive communication
from the hub. Long wake-up
interval will not affect how oen the
sensor reports to your hub so we
recommend leaving the default
setting to conserve battery.
The XS Sensor supports Group 1 for
Lifeline communication and Group
2 with up to 5 devices for basic
on/off control. This device will send
a Basic Set command to Group 2
whenever it detects water. The
value of the basic set command
sent to Group 2 can be adjusted in
the advanced settings to customize
the sensor’s behavior.
Please note that not all Z-Wave
systems give users access to direct
association settings so if you’re
note sure where to find it, please
get in touch with our support and
we’ll be happy to help.
TROUBLESHOOTING
EXCLUSION (REMOVE DEVICE)
FACTORY RESET
WAKE-UP MODE
ASSOCIATION
PAGE 1 PAGE 2
SmartThings
detection contacts
Add language about LR
Z-WAVE
BUTTON
3 x CLICK
TO PAIR
SCAN
QR CODE
FOR SMARTSTART
INCLUSION
Z-Box Hub

ADVANCED SETTINGS
Parameter 1: Turn the LED
indicator on (blinking) or off when
a water leak is detected.
Values: 0 – LED indicator won’t
blink when the sensor detects a
water leak; 1 – LED indicator will
blink when the sensor detects a
water leak (default).
Size: 1 byte dec
Parameter 2: Decide how long the
sensor should report water leak
detection aer a leak is no longer
detected on the sensor side.
Values: 0 - 3600 (seconds)
Default: 0 (reports “dry” to the hub
immediately aer a leak is no
longer detected)
Size: 1 byte dec
Parameter 4: Decide when the
sensor should report low battery
to the hub.
Values: 10-50 (% battery life).
Default: 20
Size: 1 byte dec
Click the Z-Wave button 4 times
quickly to wake the sensor up
aer updating the settings.
We listed the most helpful settings
above. For a complete list of
parameters, please go to
www.support.getzooz.com
or scan the QR code
for a direct link to
all of the settings.
Not sure how to access advanced
settings on your hub? We’ll help!
[e-mail]
1. We recommend including your
sensor to the Z-Wave network
from the location you want to
install it.
2. Choose a spot in the area you
would like to monitor for water
leaks which will not be easily
accessible to pets or children to
avoid it being misplaced.
3. Simply place the sensor on a flat
surface with the 4 probes
touching the ground for best
results. The sensor will detect a
leak when water reaches any of
the 2 probe pairs shown in the
below drawing.
4. Test the sensor by simulating a
leak - it should start blinking and
send a report to the hub when
water is detected.
1. This sensor is rated which IP66
means it is dust-tight and
protected from heavy rainfall. We
recommend placing the sensor
under eve to prevent long
exposure to direct sunlight when
using it outdoors.
2. Add the sensor to Z-Wave from
the area where it will be installed
for best connectivity results.
3. Simply place the sensor on flat
surface you would like to monitor
for leaks so that all 4 probes
under the sensor are touching
ground. The sensor will report a
leak to the hub anytime water is
present between any of the
probe pairs pictured in the
drawing.
SENSOR PLACEMENT
INDOOR PLACEMENT
ZWAVEPLUS_INFO_V2
ASSOCIATION_V3
MULTI_CHANNEL_ASSOCIATION_V4
ASSOCIATION_GRP_INFO_V3
TRANSPORT_SERVICE_V2
VERSION_V2
MANUFACTURER_SPECIFIC
DEVICE_RESET_LOCALLY
POWERLEVEL
BATTERY
SECURITY_2
NOTIFICATION_V8
INDICATOR_V3
ENSOR_BINARY_V2
CONFIGURATION_V4
WAKE_UP_V2
SUPERVISION
FIRMWARE_UPDATE_MD_V5
This product can be included and
operated in any Z-Wave network
with other Z-Wave certified devices
from other manufacturers and/or
other applications. All non-battery
operated nodes within the network
will act as repeaters regardless of
vendor to increase reliability of the
network. This product features the
latest Security 2 (S2) framework to
remove smart home network
hacking risks. This device is equip-
ped with a unique authentification
code for trusted wireless
communication.
ŸThis product should be installed
indoors or outdoors under eve
upon completion of any building
renovations.
ŸPrior to installation, the device
should be stored in a dry, dust-
and-mold-proof place.
ŸDo not install the device in a place
with direct sun exposure, high
temperature, or humidity.
ŸKeep away from chemicals, water,
and dust.
ŸEnsure the device is never close to
any heat source or open flame to
prevent fire.
ŸNo part of the device may be
replaced or repaired by the user
except for the batteries.
This product is covered under a 12-
month limited warranty and 5-year
extended warranty once registered.
To read the full warranty policy,
register your product, or file a
warranty claim, please go to
ww.getzooz.com/warranty
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND
AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR
DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE
INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER
IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S
LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY
CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF THE PRODUCTS,
WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY,
BREACH OF WARRANTY, BREACH OF AGREEMENT, OR
EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT
ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF
THE PURCHASE PRICE FOR THAT POR-TION OF PRODUCTS
WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL
CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL
BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN
THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE
FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN
USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY
EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used according to
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in any given installation.
If this equipment causes harmful interference to radio or
television reception, the user may try to correct the
interference by taking one or more of the following
measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from
receiver
- Consult the dealer or an experienced radio/TV technician
for additional assistance
All brand names displayed are trademarks of their
respective holders.
© Zooz 2023
S2
WARNING
WARRANTY
PAGE 4
Water detection between 2 points.
NO water detection between 2 points.
OUTDOOR PLACEMENT
PAGE 3
COMMAND CLASSES
Scan to register
your product for
extended warranty
and direct access to
firmware files.