ZOSI 8AP-2893W User manual

Wireless Security Camera System
Quick Start Guide
For more informaon of your new system, please refer to www.zositech.com
V6.I.01.Z

EN
ES
FR
DE
IT
NL
01
12
23
34
46
57
Contents

1
1Gallery & Specs
1.2 Wireless IP Camera
1.1 NVR
HDMI Port
VGA Port
Audio Output
Network Port
AntennaAntenna
USB Mouse
USB Backup
Power Supply
NetworkPort
PowerPort
Antenna
Microphone
Speaker
SpotlightX4
IR-LEDX4
Lens

2
2System Connecon
2.1 Connect NVR to the Internet
(1) Connect NVR to router using a network cable.
(2) Connect monitor to NVR via HDMI or VGA port.
(3) Connect the included USB mouse to the top USB port of NVR.
(4) Connect NVR to 12V power supply.
(5) Aer the system starts, pair and connect IPC and camera to the system (maximum support 8
channels).
(6) The monitor will show the real-me monitoring picture of the camera.

3
A: Camera Installaon Diagram
B: How to test the network status of NVR?
(1) Right click Mouse > Go to Main Menu > Seng > Network
(2) Tick 'Obtain IP address automacally'
Click 'Test', if 'OK' is displayed, ck ‘DHCP’ and apply, the device will automacally assign the
corresponding network segment and IP address. Aer clicking Test, if the page is displayed
successfully, it is successfully connected to network.
NOTE: Please make sure that the DHCP of the connected router is enabled at the same me.
❶ Following the mounng hole template to drill holes in the wall and insert the wall plugs.
❷ Align the camera Base with the mounng hole template, using the screws to fix the base.
❸ Manually rotate the angle of the camera to adjust the appropriate monitoring angle.
NOTE: Place the camera wire in the notch of the camera base.

4
C: WiFi Setup
Right-click the main interface - Main Menu - Setup - Network - Wireless Network, default seng and
apply.
2.2 Download ZOSI Smart App
Zosi Smart App (IOS/Android) App video operaon link

5
3AVSS PC Client
3.1 Install AVSS on PC
Get the AVSS soware from www.
zositech.com or from your agent.
Double-click the icon AVSS to open,
select the language and click Login.
Note: You can log in with the default
username and password, or register a
new account.
The user name is the account an
password registered on the App in 2.3.
3.2 Device Management
Click the Add Device buon in the device list to add/edit/configure/search for the device.

6
3.3 Live View 3.4 Video Playback
Select channel to watch live streaming. Select ‘Playback’, select device, channel, date,
me, click the play buon to start replaying
recorded video.
4Add Device
4.1 Add IPC to wireless camera system
(1) Connect IPC and NVR in the same wireless network.
(2) Right-click the mouse on the live channel page and get the main menu.
(3) Click IPC Channel Config to enter the configuraon page.
(4) Click the search buon to search for IP cameras.

7
(5) Tick the IPC channel, click WiFi add.
(6) The IPC device is successfully added and it can be displayed in live view channel and operated.

8
5Hard Drive/ Micro SD Card
Some camera kits may not contain hard drives, depending on the camera kit you
purchase. This kit support most 3.5” HDD.
NOTE: Please skip this step if your recorder has a pre-installed hard drive.
① Power off the NVR, unscrew and remove the top cover of recorder.
② Connect the power cable and data cable of the hard drive to the corresponding
ports in the recorder.
③ Put the hard disk into the recorder. All wires should cross up over the hard drive.
④ Hold the hard disk and the NVR, gently turn it over and line up the holes on the
hard disk with the holes on the NVR. Use a Phillips screwdriver, screw the included
screws into the holes.Assemble the cover.
You need to format the hard drive before recording. Right click mouse> Main
Menu> Hard Disk Management> select Hard Disk> Format> Apply.
1. Remove the top cover
3. Fix Hard drive 4. Assemble the cover
2. Hard disk wiring