Zte MF60 User manual

Mobile WiFi Mobile WiFi
User Guide
ZTE MF60

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
LEGAL INFORMATION
Copyright © 2013 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microlm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make modi-
cations on print errors or update specications without prior notice.
Version No. : R1.0
Edition Time : 2013-1-6
Manual No. :
NOTE:
Do not use the device in an enclosed environment or where heat dissipation is
poor. Prolonged work in such space may cause excessive heat and raise ambient
temperature, which may lead to automatic shutdown of the device for your safety.
In the case of such event, cool the device in a well-ventilated place before turning
on for normal use.
1

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
Getting to Know Your Device
Appearance
The following gure shows the appearance of the device, it is only for your refer-
ence. The actual device may be different.
Right Side Front Left Side Bottom
Interface and Buttons
1.Power Hold the Power button to switch on/off the device.
2.Memory card slot
(microSD card) It is where you insert the memory card (microSD card).
2

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
3.WPS
This button is used to start/end Wi-Fi Protected Setup au-
thentication process and enable/disable the Wi-Fi function.
Hold it for 3 seconds to activate the WPS function.
When the WPS function is available, press it to deacti-
vate the WPS function.
Press it to enable/disable Wi-Fi function.
4. OLED Screen It indicates the signal type, signal strength, battery, Wi-Fi,
etc.
5. External An-
tenna Connector
It is used to connect an external antenna to enhance the
signal strength.
6.Charger/USB
port
Charge your device.
Connect the client to your device via USB cable.
NOTES:
microSD logo is a trademark of SD Card Association.
Hold the WPS and Power buttons simultaneously until the OLED screen
turns off, and then release the buttons. The device will restart automatically
and restore to the factory default settings.
3

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
Indicators
When the device is powered on, the following icons will appear on the OLED
screen, with the corresponding indicates listed in the table below:
Icon Indication
Network signal strength.
2G
3G
Network type. 2G or 3G icon will appear on the OLED
screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
New message received.
Wi-Fi Status and number of the connected users.
Battery power indication.
Connect/Disconnect The device connects / disconnects the Internet.
4

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
Connection Scenario
The following picture is the application example. All of the client devices can surf
on the Internet at the same time.
NOTES:
You can only use USB cable or Wi-Fi to connect this device.
 If you want to use Wi-Fi, make sure the client supports the Wi-Fi function.
 It is recommended that the operating system of your PC is Windows XP SP3
(32 bit), Windows Vista, Windows 7, Windows 8, or MAC (10.5 or later) client
to connect to your device.
5

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
Installing Your Device
1. Use the thumb catch at the bottom of the device to open the battery cover.
2. Insert the SIM card into the SIM card holder.
6

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
3. Insert the battery as shown with the contacts located against the metal
springs, and press the battery down into the case.
4. Line the battery cover up correctly and press gently to close the case.
7

Mobile WiFi Mobile WiFiMobile WiFi Mobile WiFi
5. Insert the microSD card.
1) Pull the microSD cover out of the card slot.
NOTE: Do not pull the cover rudely, as it is connected with the device.
2) Insert the microSD card into the microSD slot. The following picture shows
the correct inserting direction. You will hear a click when the microSD card
locks in place.
3) Close the microSD card cover.
8