ZyXEL Communications ES-315 User manual

Copyright © 2007. All rights reserved
ES-315
Intelligent Layer 2 Managed Switch
Quick Start Guide
Version 3.70
7/2007
Edition 1
DEFAULT LOGIN
IP Address http://192.168.1.1
Username admin
Password 1234

ES-315 Quick Start Guide
1
1 Overview
Your ES-315 is an intelligent layer-2 Ethernet switch. Use it to
connect up to four Ethernet devices to your network. The
following example shows your ES-315 (A) connecting several
devices (1~ 4) and allowing them to communicate with one
another and access the Internet through the Internet Service
Provider’s network switch (B).
This Quick Start Guide shows you how to do the following:
Make Hardware Connections on page 2.
Log Into the Web Configurator on page 6.
Set the Password on page 8.
Set Up Your Network on page 11.
Wall-mount the ES-315 on page 15.

2
ES-315 Quick Start Guide
2 Make Hardware Connections
1WAN: using an Ethernet cable, connect the WAN port to
your Internet source.
2LAN: using another Ethernet cable, connect your
computer to one of the LAN ports (1, 2, 3or 4) for initial
configuration.
3POWER: using the included power adaptor, connect the
POWER socket to an appropriate power source.
"Use only the power adaptor that came with the
ES-315.
Look at the LEDs (lights) on the front of the ES-315.

ES-315 Quick Start Guide
3
•ThePWR/SYS LED turns green if the power is on.
•TheLAN 1, 2, 3 or 4and WAN LEDs turn on when the corre-
sponding ports are properly connected, and blink when there
is traffic.
VIf one of the LEDs does not behave as
expected, check the connection. Make sure the
device to which the corresponding port is
connected is turned on and working normally. If
this does not help, turn the ES-315 off and on
again.
2.1 Set Up Your Computer’s IP Address
This section shows you how to set up your computer to
access the ES-315.
You must set your computer to use a static IP address in the
192.168.1.2 - 192.168.1.254 range with a subnet mask of
255.255.255.0. This ensures that your computer can
communicate with your ES-315.
The following instructions are for the Windows 2000,
Windows NT and Windows XP operating systems.
1In Windows XP, click Start > Control Panel.
In Windows 2000/NT, click Start > Settings > Control
Panel.

4
ES-315 Quick Start Guide
2In Windows XP, click Network Connections.
In Windows 2000/NT, click Network and Dial-up
Connections.
3Right-click Local Area Connection and then click
Properties.
4Select Internet Protocol (TCP/IP) (under the General tab
in Windows XP) and click Properties.
5The Internet Protocol TCP/IP Properties screen opens
(the General tab in Windows XP).

ES-315 Quick Start Guide
5
"Note down your computer’s current IP settings
before you change them. You may need them
later.
6Select Use the following IP address and fill in the IP
address (choose one in the range 192.168.1.2 -
192.168.1.254), Subnet mask (255.255.255.0), and
Default gateway (192.168.1.1) fields.
7Click OK to close the Internet Protocol (TCP/IP)
Properties window.
8Click Close (OK in Windows 2000/NT) to close the Local
Area Connection Properties window.

6
ES-315 Quick Start Guide
Close the Network Connections window.
3 Log Into the Web Configurator
Take the following steps to access the ES-315 for initial
configuration.
"Use Internet Explorer 6.0 and later versions or
Netscape Navigator 7.0 and later versions with
JavaScript enabled and pop-up blocking
disabled.
Open an Internet browser (such as Internet Explorer or
Netscape Navigator). Enter the ES-315’s IP address in the
address bar.
"The ES-315’s default IP address is 192.168.1.1.

ES-315 Quick Start Guide
7
A window similar to the following appears.
Enter the default username (admin) and the default password
(1234). Click OK.
VIf you do not see this screen, make sure that
your Internet browser allows pop-up windows (in
Internet Explorer, select Tools > Pop-up
Blocker and then select Turn Off Pop-up
Blocker). Reload the web page.
If this does not help, make sure the IP
addresses and subnet masks of the ES-315 and
the computer are in the same IP address range
(see section 2.1).

8
ES-315 Quick Start Guide
The Status screen displays.
4 Set the Password
For security reasons, you should change the password when
you first log in.
Take the following steps to do this.

ES-315 Quick Start Guide
9
1Click Management in the navigation
panel on the left of the screen. In the
menu that displays, click Access
Control. Then, click Logins.
2The following screen displays.
3Enter the login information you want to use, as follows.