ZyXEL Communications NBG-334SH User manual

NBG-334SH
Super G High Power Wireless Router
Quick Start Guide
Version 3.60
01/2007
Copyright © 2007. All rights reserved.
Table of Contents
ENGLISH 3
DEUTSCH 19
ESPAÑOL 37
FRANÇAIS 55
ITALIANO 73
SVENSKA 89
繁體中文 105

ENGLISH
3
Overview
The NBG-334SH is an IEEE 802.11b/g wireless broadband router with Super G capability.
The NBG-334SH also features a four-port 10/100 Mbps switch.
You should have an Internet account already set up and have been given most of the
following information.
Table 1 Internet Account Information
See your User’s Guide for background information on all features.
The following lists what you need to do:
1Make Hardware Connections
2Access the Web Configurator
3Follow the Connection Wizard
Your device’s WAN IP Address (if given): ______________
DNS Server IP Address (if given): Primary _____________, Secondary ______________
Connection Type:
Ethernet Service Type:
_______________________
User Name: ____________
Login Server IP Address:
______________
Password: ____________
PPTP: User Name: ____________
Your WAN IP Address (if given)
____________
Connection ID (if required):
____________
Password: ____________
PPTP Server IP Address:
___________
or PPTP Domain Name:
___________
PPPoE (PPPoE) Service Name:
____________
User Name: ____________
Password: ____________
ENGLISH

ENGLISH
4
1 Hardware Connections
Do the following to make hardware connections for initial setup.
WAN Connection
Connect your modem to the WAN port using the cable that came with your
modem.
LAN Connection
Connect your computer to a LAN port using the included Ethernet cable.
POWER Connection
Use the included power adaptor to connect the POWER socket to an appropriate
power source.
The LEDs
Look at the LEDs (lights). When you connect the power, the PWR LED blinks and stays on
once the device is ready.
1
2
3

ENGLISH
5
The LAN, WAN and WLAN LEDs turn on if the corresponding connections are properly
made.
VIf the LEDs are different from this, check your connections. Turn the NBG-
334SH off, wait for a few seconds and turn it back on.
2 Accessing the Web Configurator
1Launch your web browser. Enter “192.168.1.1” as the web site address.
VIf the login screen does not display, check your browser’s security settings
or make sure your computer is set to receive an IP address dynamically
(see Set Up Your Computer’s IP Address).
If you cannot access the web configurator using Internet Explorer in
Windows XP or Windows Server 2003, make sure you allow pop-up
windows, JavaScripts and Java permissions or set the Internet security
level lower than High in Internet Explorer (in Internet Explorer, click Tools >
Internet Options > Security > Custom Level...). See the appendix in the
User’s Guide for more information.

ENGLISH
6
2The Password window displays. Enter the password (“1234” is the default) and click
Login.
3Change the password in the screen that follows and click Apply.
4Click Go to Wizard setup to set up your NBG-334SH for the first time.
3 Connection Wizard Setup
1After you log into the web configurator and click Go to Wizard setup,choose your
language from the drop-down list box. Click Next.
2Click Next to proceed with the Connection Wizard.

ENGLISH
7
Internet Access Setup
"Enter the Internet access information exactly as given to you by your ISP in
each wizard screen and then click Next to continue or click Back to return
to the previous screen. Current screen information will be lost if you click
Back.
STEP 1: System Information
This screen is optional. You can just click Next.
•System Name is for identifying the NBG-334SH. You can enter your computer's "Computer
Name".
• If you leave the Domain Name blank, the domain name obtained by DHCP from the ISP is
used.
STEP 2: Wireless LAN
Configure ONE of the following wireless security types on the NBG-334SH:
•Auto security: Have the NBG-334SH automatically generate a pre-shared key.
•None: Have no wireless LAN security configured. If you do not enable any wireless security
on your NBG-334SH, your network is accessible to any wireless networking device that is
within range.
•Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting
over the wireless network. The higher the WEP Encryption, the higher the security but the
slower the throughput.
•Extend (WPA-PSK or WPA2-PSK) security: Configure a Pre-Shared Key. Choose this
option only if your wireless clients support WPA-PSK or WPA2-PSK respectively.

ENGLISH
8
"The wireless clients and NBG-334SH must use the same SSID, channel ID
and WPA(2)-PSK (if WPA(2)-PSK is enabled) or WEP encryption key (if
WEP is enabled) for wireless communication.
Auto or No Wireless Security
A Enter a unique name to identify the NBG-334SH in the wireless LAN.
B Select a wireless security level. Choose Auto or None.
C Select a wireless channel. The NBG-334SH and wireless client must use the same
channel.
D If you select Auto and click Next, a screen pops up displaying the generated pre-shared
key. Click OK to continue. You can also view the generated pre-shared key in the Wireless
LAN > General screen.
Basic (WEP) Security
A Enter a unique name to identify the NBG-334SH in the wireless LAN.
B Select Basic(WEP) security.
C Select the wireless channel. The NBG-334SH and wireless client must use the same
channel.
D Select 64-bit or 128-bit from the WEP Encryption drop-down list.
E Select ASCII or Hex WEP key input method.
F You can create a WEP key by either:
Entering a Passphrase (up to 32 printable characters) and clicking Generate to have the
NBG-334SH automatically generates four WEP keys.
Or
Manually entering a key in each Key (1~4) field.
A
B
C
D

ENGLISH
9
G Select one of the Key radio buttons to use as the default WEP key.
Extend (WPA-PSK or WPA2-PSK) Security
A Enter a unique name to identify the NBG-334SH in the wireless LAN.
B Select WPA-PSK or WPA2-PSK security.
C Select the wireless channel. The NBG-334SH and wireless client must use the same
channel.
D Type a pre-shared key to have a more secure wireless connection than WEP encryption
provides. Type from 8 to 63 case-sensitive ASCII characters. You can set up the most
A
B
C
E
F
D
G

ENGLISH
10
secure wireless connection by configuring WPA(2) in the advanced wireless screen. You
need to configure a RADIUS server to do this.
STEP 3: WAN
The wizard attempts to detect which WAN connection type you are using.
If the wizard cannot detect a connection type, you must select one of the options from the drop-
down list box. Check with your ISP to make sure you are using the correct type:
1Ethernet
2PPPoE
3PPTP
A
B
C
D