ZyXEL Communications P-660HW-61 Instruction Manual

ZyXEL Confidential
340PE10C0.doc 1/42
ZyXEL
Firmware Release Note
Prestige 660HW-61
Standard version
Release 3.40(PE.10)C0
Date: Oct 28 ,2005
Author: Ross

ZyXEL Confidential
340PE10C0.doc 2/42
ZyXEL Prestige 660HW-61 Standard Version
Release 3.40(PE.10)C0
Release Note
Date: Oct 28, 2005
Supported Platforms:
ZyXEL Prestige 660HW-61
Versions:
ZyNOS Version : V3.40(PE.10) | 10/28/2005 16:00:00
Bootbase Version : V1.06 | 04/01/2004 11:22:33
Notes:
The Prestige 660HW-61, is 4th generation of ZyXEL ADSL product family. It is a high
performance ADSL/ADSL2/ADSL2+ router for small/medium office to have Internet
access and LAN-to-LAN application over the existing copper line. P660HW-61 takes
advantage of much higher data rate than ADSL, speed up to 12Mbps (ADSL2) or 26Mbps
(ADSL2+), greater reach, faster start-up, advanced diagnostics and better power
management. This high performance ADSL router is a high integrated advanced Firewall,
Bandwidth Management and IEEE 802.11g wireless features to meet the demand of
high-end market.
P660HW-61 provides an embedded mini-PCI module for 802.11g Wireless LAN
connectivity, four single auto-sensing, auto-detection 10/100BASE-T Ethernet ports for
connection to the user’s local network, and a single RJ-11/RJ-45 port for connection to
ADSL/ADSL2/ADSL2+ line.
ADSL data pump version: TI AR7 04.02.01.00
Features:
Modifications in V 3.40(PE.10)C0 | 10/28/2005
1. Change to FCS version
2. Change default rom file
Enable wireless 4X mode; Enable Wireless qos.
Modifications in V 3.40(PE.10)b1 | 10/09/2005
1. [Feature Enhancement]
Employ Cone NAT, N2P support.
2. [Feature Enhancement]
From APDK5.2 change to APDK6.0,support WMM and WPA2.
3. [Feature Enhancement]
Enhancement for zero configuration. Add a new page zCfgTryAgain.html. This

ZyXEL Confidential
340PE10C0.doc 3/42
page will be showed when DSL line has not up. Close web redirect once PPPOE user name
and password are right
4. [Feature Enhancement]
disable Webredirect, Ways to disable Zero configuration, web redirection and VC
auto-hunt completely. Zero configurations should have right wording(it should show
“PPP” in stead of former “PPPoE”) in the URL about PPPoE/PPPoA.
5. [Feature Enhancement]
Throughput enhancement for TI platform
6. [Feature Enhancement]
Support MSN Messenger 6.2 & 7.0 passthrough without UPNP enabled.
7. [BUGFIXED]
SPRID:050916691
Symptom:Whiteboard(WAN to LAN) can’t work well when UPNP is enable.
Condition:Whiteboard(WAN to LAN) can’t work well in all of the following conditions.
1.OS is based on WinXP;
2.enable UPNP and ”Allow users to make configuration changes through UPnP ” in
GUI-UPNP;
3.make sure that wan should be first to ask for whiteboard;
4.MSN6.2-MSN6.2;MSN7.0-MSN6.2;MSN6.2-MSN7.0;MSN7.0-MSN7.0.
8. [BUGFIXED]
SPRID:050916685
Symptom: if we set dhcp start ip address to a wrong range, we still can save these setting
Condition: set dhcp ip address to conflict with router lan ip address, and we can save
these setting in menu 3.2
9. [BUGFIXED]
SPRID:050916686
Symptom: Chariot testing fail if simultaneously select multiple Chariot script.
Condition: Topology: EndPoint1--660R--DSLAM--BRAS--Endpoint2
Selecting all 10 internet standard scripts(\netiq\chariot\script\internet\) run at
the same time for a long continuous time, error with the number
0245 in Chariot
will occur and it will stop the test.
10. [BUGFIXED]
SPRID:050916687
Symptom: While WAN encapsulation is set to ENET ENCAP and dynamic IP address is
used, if WAN IP
is changed, NAT session will not be reset, it will cause internet access fail.
Condition: (1)Set DUT WAN encapsultion to ENET ENCAP and dynamic IP address,
after get IP address from DHCP server on WAN side, internet access can be
successful.
(2)Edit the static DHCP pool of DHCP server on WAN side to allocate another IP
address to DUT, and pull out ADSL line for a moment and insert it to ensure IP
re-allocation.

ZyXEL Confidential
340PE10C0.doc 4/42
(3)After get new IP, internet access will be fail.
11. [BUGFIXED]
SPRID:050916688
Symptom: The "Connection testing" page will not change to " Connection testing Fail"
page If there are no corrcet PVC in hunting table
Condition: If there are no corrcet PVC in hunting table then getHuntState()
function never return AUTO_HUNT_FAIL.
12. [BUGFIXED]
SPRID:050916690
Symptom: If wireless LAN card is removed from P660HW-6x board, rom-t file get from
device will be disorder
Condition: Remove wireless LAN card from device, then get rom-t, title and content will
not
match for some items.
13. [BUGFIXED]
SPRID:050916692
Symptom:In GUI, The WAN Backup functions need at least one none-zero Check WAN
IP
Condition:ICMP mode this is right,but in DSL Link mode this is wrong.
14. [BUGFIXED]
SPRID:050916696
Symptom: lan can’t ping wan when change encapsulation
Condition: 1.lan ping wan 192.168.8.2 continusly.
2.In SMT Menu4,change encapsulation to PPPoE,lan can ping wan.
3.change encapsulation to ENETCAP or RFC1483,lan PC can’t ping wan.
15. [BUGFIXED]
SPRID:050916708
Symptom: Traffic redirect work have problem.
Condition: Step1 Use ENEP ENCAP, in DUT and device in menu 3.2 turn off RIP
Step2 In DUT menu2.1 set backup gateway is 192.168.1.5 and in device 3.2 LAN ip set
192.168.1.5
Step3 from LAN pc ping wan pc 192.168.8.11 -t (same subnet as wan ip) it is ok ,then
pull off DUT wan
line, the traffic go out from device, but when plug into the DUT wan line, then the
traffic can
not go out, pc reboot is ok but use ENET ENCAP ping outside ip such as
202.96.209.5 is ok, and
use PPPOE ping inside ip such as 192.168.8.1 is also ok)
16. [BUGFIXED]
SPRID:050916710
Symptom: If one WLAN client connect to device using WPA-PSK, then change the
mode
from WPA-PSK to WPA. Device will exception.
Condition: If one WLAN client connect to device using WPA-PSK, then change the
mode
from WPA-PSK to WPA. Device will exception.

ZyXEL Confidential
340PE10C0.doc 5/42
17. [BUGFIXED]
SPRID:050916711
Symptom: If turn on the WLAN WPA-PSK mode, then the second PPPoE connection
will not work.
Condition: 1. Set a PPPOE connection in remote node 2.
2. The PPPOE will up.
3. Turn on WLAN WPA-PSK then the PPPOE connection will down.
18. [BUGFIXED]
SPRID:050916712
Symptom: If using MultiBoot V2 and update all files (bootbase, rom and ras)
,it should be no problem to support different size bootbase/rom , but occurs fail.
Condition: upload all files,if bootbase/rom file size is different from old f/w ,it always
occurs fail,
RAS file can't write to flash.
19. [BUGFIXED]
SPRID:050916713
Symptom: When DUT use static IP and set DNS server address in
GUI->wizard, DUT won’t resolve domain name successfully until reboot
Condition:Step1 Go to GUI, configure DUT use static IP and set DNS server, then go
to Maintenance->Diagnostic, try to resolve domain name, but failed
Step2 Reboot DUT, it works fine
Step3 This many cause TMSS/AV/CAC/DDNS functions doesn’t work for
these
functions need DUT resolve domain name
20. [BUGFIXED]
SPRID:050916714
Symptom：PPPoA idle time issue
Condition1: 1. PPPoA and LAN PC ping WAN PC continuously
2. Reboot device ,it can not connection to the remote node
Conditon2: 1. PPPoA and choose nail-up yes
2. in SMT-4 or SMT-11 change between two right accounts ,device can not connect
to remote node
21. Change datapump to 4.2.1.0
22. [BUGFIXED]
SPRID: 051008870
Symptom : PPPoE LED can’t lighting when use PPPoA Encapsulation sync up.
Condition: Use PPPoA Encapsulation to sync up.
Modifications in V 3.40(PE.9)C0 | 5/13/2005
1 change to FCS
Modifications in V 3.40(PE.9)b3 | 5/13/2005
1[BUG FIXED]
Wireless IOP issue.
Modifications in V 3.40(PE.9)b2| 4/28/2005
1[Feature Enhancement]

ZyXEL Confidential
340PE10C0.doc 6/42
When you use reset button to start OTIST, it also can general WPA-PSK key
2[BUGFIXED]
Symptom: After disable SIP ALG, MBM can’t work for VOIP traffic.
Condition: (1)disable SIP ALG via C/I command,
(2) Set a rule in MBM for SIP application
(3)use a ATA to dial to another SIP client via SIP proxy, the traffic can’t managed
by MBM.
3[BUGFIXED]
SPRID:050419922
Symptom: then redirect to the page of Test Frame ceaselessly
Condition:
When popup the page of change username and password in zero configurations, input the
inaccurate username and password,
Modifications in V 3.40(PE.9)b1| 4/11/2005
1Support ADSL 2+ by TI modem code 3.2.6
2 [Feature Update]
add mutiboot firmware upgrade feature
3 [Feature Enhancement]
Add SIP ALG enable /disable in eWC(by default disable)
4 [Feature Enhancement]
In GUI ,add a checkbox to control wireless g+ (by default enable)
5[Feature Enhancement]
Diffserv in MBM.
6 [Feature Enhancement]
MBM mapping to ATM queque
4.5.6.7-> ATM high queue
0.1.2.3->ATM low queue
7[Feature Enhacnement]
Add a drop list for user to choose “802.11g only””802.11b only” ”mixed ”
8 [Feature Enhacement]
Pop-up a warning message” your pass word username is wrong please check”, if user enter
the wrong id and password when doing zeroconfig
9 change default MAC to 001349000001
10. [BUG FIXED]
TE report device will reboot about 3%-7% when change wireless config.
11[BUGFIXED]
Symptom: it should show test html and popup a success html or change username or
password html. But it show nothing else login GUI.
Condition: when zero configure is enable .
12. [BUG FIXED]
Symptom: device will crash
Condition: we ftp to device and then change to http in IE browser
13 [BUG FIXED]

ZyXEL Confidential
340PE10C0.doc 7/42
Symptom: it will show some error message, when device boot up
Condition: when F/W load to a device without wireless card.
14[BUG FIXED]
Symptom: wireless can not connect to device with WEB 256-bits
Condition: N/A
15. [BUG FIXED]
Symptom: they find the first hop and the second hop is the same one
Condition: the PC behind device tracert router
16．[BUG FIXED]
SPRID:050107337
Symptom: in eWC NAT can not work correctly if I change the Server Mapping Set.
Condition:
Step1: in eWC =>Advanced Setup=>NAT,choose Full Feature and Edit the Rule 1;
Step2: choose the Type as Server mode,and set the Globle IP as the Wan ip of the DUT;
Step3: Server Mapping Set choose 2,and Edit Details,and add the Port 2121 forward to the
LAN PC "10.0.0.2";
Step3: using an PC in the Wan to access the ftp(port 2121) server on the LAN PC.This
must be successful;
Step4: then choose the Server Mapping Set 3, and Edit Details to add the Port 23 forward to
the LAN PC. then Apply.
ftp from the WAN to the LAN also can successful, but telnet from WAN to LAN can not
work.
Then reboot the DUT, the Server Mapping Set 3 can work, but the details shows the error
information.
17．[Bug Fixed]
SPRID: 041028829
Symptom:You can not modify firewall rule, Nat - address mapping rule does not show
in the approciate / exact colum
Condition:if using other web browsers like Mozilla 1.7.5.
18．[BUG FIXED]
Symptom: the device will crash
Condition: when vchunt is active and delete menu 4
19．[Feature update]
Recovery 802.11 mode changing command.This command can't be saved into romfile
same as 5.0.7.
20．BUG FIXED]
Symptom: Customer reported if a link request is given in IE can hang/reboot the
ZyXEL-device.
Condition:http://192.168.1.1/Forms/rpAuth_1?ZyXEL%20ZyWALL%20Series <script>t
op.location.pathname=%20""</script>
21.[BUG FIXED]
Symptom: using wordpad edit the rom-t file, the PPPoE password will be
changed unexpected.

ZyXEL Confidential
340PE10C0.doc 8/42
Condition: (1)In SMT menu4, set encapsulation to PPPoE mode and make sure the
DUT can dial up.
(2) Get rom-t and use wordpad to edit it, change the sysname to ”hehe”
and save.
(3) upload the edited file to the DUT, and the DUT can’t dial up PPPoE
password is changed to correct one.(use notepad and UltraEdit have no problem)
22 [BUG FIXED]
SPRID:041230566
Symptom: The “Back” button in LAN Setup can’t work correct.
Condition: Step1. In GUI/Advanced Setup/LAN/LAN Setup, change some settings.
Step2. Click “Back” button, the DUT can save it successfully.
23[BUG FIXED]
Symptom: secondary DNS server doesn’t work
Condition: connect DUT to LAN port of ZyWALL via IES, the wan port of ZyWALL
is connected to internet; DUT gets IP address and DNS server from ZyWALL’s DHCP
server; when primary DNS server is unreachable, secondary DNS server doesn’t work
either.
24[BUG FIXED]
Symptom: When we get rom-t from LAN side by FTP , and modified it, then put
rom-t ,the device won’t accept the new rom-t. (Just only use ultraedit modify rom-t,
the DUT can accept it, but while use other utilities--DOS
Edit/Word/Notepad/WordPad modify the rom-t, the DUT can not accept it.)
Condition: N/A
25[BUG FIXED]
Symptom: TFTP Firmware upload failure
Condition: In menu 24.11, leave the telnet server port default, upload firmware using
tftp from lan side pc, it always fails; but if telnet server port is changed to 23, the
function works well
26[BUG FIXED]
SPRID: 041224286
Symptom: SMT&eWC standard show is different
Condition: In menu 24.2.1, show Standard :Multi-Mode, but in eWC
Maintenance->System Status,Standard :ADSL_G.dmt
27[BUGFIXED]
Symptom: it failed to login eWC when input 31 characters
Condition: When set 31 characters password on eWC,DUT will accept it
28[BUGFIXED]
SPRID:050329394，050307379
Symptom: When 2 PCs visit eWC of DUT, the priority have some problem
Condition: Step1 The first PC visit the eWC of DUT, and keep login status
Step2 Then the second PC temp to access the eWC of DUT, and show the page of
password entry Step3 Clicking login make the first PC logout automatically, although
the second PC also can not login eWC
29[BUGFIXED]

ZyXEL Confidential
340PE10C0.doc 9/42
Symptom: After disable SIP ALG, MBM can’t work for VOIP traffic.
Condition: (1)disable SIP ALG via C/I command,
(2) Set a rule in MBM for SIP application
(3)use a ATA to dial to another SIP client via SIP proxy, the traffic can’t managed
by MBM.
30[BUGFIXED]
SPRID: 050310549
symptom: we can not set device ip 0.0.0.0 in SMT ,but we can set it in eWC
condition: N/A
31 ADSL CI command format changes
32 [Feature Change]
We can not delete menu 4.
33[BUGFIXED]
Symptom:Wireless hang-up eMule throught WLAN
Condition: N/A
34[BUG FIXED]
Symptom: Special URL will cause system crash.
Condition: Form LAN site, enter
http://192.168.1.1/Forms/rpAuth_1?ZyXEL%20ZyWALL%20Seriesscript>top.locat
ion.pathname=%20""</script> on browser, the device
will crash.
35 [BUG FIXED] (Bridge Performance)
Symptom: Bridge performance is poor.
Solution: Remove unnecessary memory movement in bpdu_handling() function.
36 [FEATURE ENHANCEMENT] (MULTICAST)
Symptom: While injecting multicast traffic from WAN to LAN in bridge
mode, CPU loading is heavier than injecting unicast traffic.
37 [FEATURE CHANGE]
Change CI command” wlan chgmode” make it can show 802.11 mode. And save
to romfile.
38[BUG FIXED]
SPRID:050301058，050310508
Symptom: In smt21.1 IP filter, IP=*.*.*.*, mask=255.255.255.0, it can save...
the correct mask is 255.255.255.255. or IP=*.*.*.0, mask=255.255.255.0
Condition: N/A
39[BUG FIXED]
SPRID: 050329394，050316845
Symptom: In GUI wireless LAN page, if click passphrase button, make checkbox of
Enable Wireless g+ inactive automatically.
Condition: Step1: In GUI wireless LAN page, input passphrase key and
click ”Generate” button.
Step2: The Checkbox of Enable Wireless g+ change from active to inactive automatically
Modifications in V 3.40(PE.8)C0| 12/23/2004

ZyXEL Confidential
340PE10C0.doc 10/42
1 change to FCS
Modifications in V 3.40(PE.8)b2| 12/17/2004
1. [BUG FIXED]
Symptom: When the PC is being connected to DUT through wireless, reboot system,
the DUT will crash.
Condition: Step1: PC(install SP2) is being connected to DUT through wireless.
Step2: At this time, reboot system
Step3: DUT will crash.
2. [BUG FIXED]
Symptom: The “Back” button in Wireless-MAC filter can’t work correct.
Condition: 1.in GUI, Advanced Setup-Wireless LAN-MAC Filter, change some
setting 2.click Back button, the DUT can save it successfully.
3. [BUG FIXED]
Symptom:
our WLAN device should disallow the client with MAC ”00:00:00:00:00:00” when
user define only allowed MAC (ex. only ”01:02:03:04:05:06” can access) via MAC filter
Condition:
Take one B220 for example, its MAC is ”00:A0:C5:43:FD:C5”.
1. Add one allowed MAC filter to ”01:02:03:04:05:06” on device via SMT menu 3.5.
2. The B220 cannot access to the device because it only allow
MAC ”01:02:03:04:05:06” to access.
3. Modify B220’s MAC to ”00:00:00:00:00:00”.
4. Then you find B220 can access device.
The WLAN client is possible to change its MAC address to ”00:00:00:00:00:00”.
Customer hope our devices should not allow the MAC like 00:00:00:00:00:00 by
default.
4. [BUG FIXED]
Symptom: anyip can’t inactive in eWC immediately
Condition: step1 in eWC active anyip it can work
step2 when inactive anyip it can still work but in SMT don’t have problem
5. [Feature Enhancement]
support wlan auto security key lenghth 0-8.
Change name to OTIST
Add help page.
6. [BUG FIXED]
Symptom: IP source address become zero in WAN side.
Condition: IP source address is translated to zero by NAT, if
destination IP address is multicast group.
7 [BUG FIXED]
Symptom: The natSetSessionPerHostForIface() causes excetion
Condition: due to the NULL pointer access. The st_p will become NULL in some
case.
8 [BUG FIXED]
Symptom: vc hunt can not alloc mbuf again when vc hunt table is more than 8