ZyXEL Communications P-2302HWL-P1 Instruction Manual

ZyXEL Confidential
360AJB0C1.rtf 1/36
ZyXEL
Firmware Release Note
P-2302HWL-P1
Standard Version
Release 3.60(AJB.0)C1
Date: September 9, 2006
Author: Chun Hsing Chien

ZyXEL Confidential
360AJB0C1.rtf 2/36
ZyXEL P-2302HWL-P1 Standard Version
Release 3.60(AJB.0)C1
Release Note
Date:September 9, 2006
Supported Platforms:
ZyXEL P-2302HWL-P1
Versions:
ZyNOS Version: V3.60(AJB.0) | 09/08/2006 17:21:22
Bootbase Version: V1.03 | 04/10/2006 11:52:50
Notes:
1. Bootbase version V1.03.
2. Support Trunking. (DTMF Mode=SIP_INFO and Compression Type codec=G.729)
3. Support No Not Disturb.
4. Support Bandwidth Management.
5. Support 802.11BG mode.
6. Support Multiboot 2.3
7. Enable quick route by default.
Known Issues:
1. Packet interval for both G.711 and G.729 is irregular.
2. Trigger port can't work if enable firewall.
3. On Consultative Transfer, when DUT-A transfer to DUT-C, it generates noise.
4. Don’t support Web Help at this moment.
5. Sometimes Blind Transfer got failure.
6. DUT can't send/receive FAX through VoIP call with Cisco T.38 gateway.
7. Intel Wireless 3945ABG (V10.1.1.3) can’t associate with DUT successfully when
DUT change 802.11 mode from 802.11g to 802.11b.
8. The Bandwidth Management's Fairness-Based don't work on LAN and WAN and
WLAN interface.
9. Audio of windows Live messenger don't establish session.
Features:
Modification in V 3.60(AJB.0) | 09/08/2006
1. Change default setting to fix REN issue.
 First Ringing Timeout to 200 msec.
 Caller ID Ring Timeout to 500 msec.
Modification in V 3.60(AJB.0) | 08/09/2006
2. Change to FCS version.

ZyXEL Confidential
360AJB0C1.rtf 3/36
Modification in V 3.60(AJB.0)b8 | 08/04/2006
[Bug Fix]
3. [SPR: 060713764] Sometimes DUT can not receive alerting tone when hop off with
Auto Attendant.
4. [SPR: 060713765] Sometimes DUT can not receive alerting tone when hop on with
Auto Attendant and DUT will reboot abnormally.
5. [SPR: 060728931] UPnP device name is incorrect.
Modification in V 3.60(AJB.0)b7 | 07/26/2006
[Bug Fix]
1. [SPR: 060711581] Wizard spoof WAN MAC address problem.
2. [SPR: 060712677] Failure rate is too high when test Continuous VoIP call with G.711
Codec by using SIP1 account with data traffic.
3. [SPR: 060718151] Can't enable "Maximize bandwidth usage" of Bandwidth MGMT
on WAN interface.
4. [SPR: 060718153] Don't Modify and disable service at Wizard .
5. [SPR: 060718155] Using BM Wizard to create subclass and delete, the default class
quantity will not increase.
6. [SPR: 0607181601] Sometimes occur to lose DTMF key in Taiwan's phone.
Modification in V 3.60(AJB.0)b6 | 07/07/2006
[Bug Fix]
1. [SPR: 060413901] DUT hang up frequently during FW testing.
2. [SPR: 060503168] IGMP-V2 don't work correctly
3. [SPR: 060313996] Voice quality is very poor with G.729 and G.711 Codec when
sending heavy traffic on LAN port.
4. [SPR: 060413890] Packets can not send and receive after Long VoIP conversation.
5. [SPR: 060413858] SmartBit throughput test got failure.
6. [SPR: 060314078] When DUT power on, PSTN phone will be dropped.
7. [SPR: 060502043] Trigger port can't work rule2 ~ rule12.
8. Remove Help Icon temporarily since there P2302HWL does not support Web Help at
this moment.
Modification in V 3.60(AJB.0)b5 | 04/27/2006
[Bug Fix]
9. [SPR: 060310918] Remove Preamble configuration in GUI.
10. [SPR: 060313994] Load default configuration from e/WC, Wireless security="Static
WEP" and passphrase=1, then you will see the channel change to ch1.
11. [SPR: 060313996] The "passphrase" and "generate button" are not grayed when
security mode is WEP Encryption to 256bit.
12. [SPR: 060411652] The picture of Internet Detection don't display in Wizard.
13. [SPR: 060411647] Wireless Security item "802.1x" should be removed in GUI.
14. [SPR: 060412804] After doing Blind Transfer, DUT-A generate dial tone with noise
in background.
15. [SPR: 060412739] Exception will happen while we change the wireless setting from
WPA-PSK to WPA.
16. [SPR: 060412674] The LED of "Internet" doesn't meet the PS definition.

ZyXEL Confidential
360AJB0C1.rtf 4/36
17. [SPR: 060413892] Don't make call after unplug DUT WAN cable during ringing on
VoIP call
18. [SPR: 060413856] In debug mode: ATBR failed to restore to default setting. It needs
to re-upload the RAS code.
19. [SPR: 060413899] Disable CallerID, DUT can not terminate a VoIP call.
20. [SPR: 060413903] DUT work as bridge during initial boot up process.
21. [SPR: 060413904] DUT maintain only one STUN setting in SIP1, change any setting
on SIP1's STUN setting will affect SIP2's stun setting.
22. [SPR: 060310898] On PPPoE connection mode to configure First DNS server from
ISP to none and Second DNS server from none to ISP, all traffic can't go out.
23. Turn on watch dog timer by default.
24. DUT can not work properly when entering a flash key during a PSTN call.
Modification in V 3.60(AJB.0)b4 | 04/10/2006
[Bug Fix]
25. [SPR: 060310913] OTIST function can not work properly.
26. [SPR: 060309829] IGMP-v1 does not work.
27. [SPR: 060309830] IGMP-v2 does not work.
28. [SPR: 060328365]WAN don't get IP address from DHCP server when enable Spoof
WAN MAC address
29. Remove 802.11a function in GUI.
30. Extend ROM file to 112 Kbytes. (Please update bootbase.bin and restore to default
setting)
31. [SPR:060314080]DTMF lost on PSTN call.
Modification in V 3.60(AJB.0)b3 | 03/30/2006
[Bug Fix]
32. [SPR: 060310913] OTIST function can not work properly.
33. [SPR: 060309829] IGMP-v1 does not work.
34. [SPR: 060309830] IGMP-v2 does not work.
35. [SPR: 060328365]WAN don't get IP address from DHCP server when enable Spoof
WAN MAC address
Modification in V 3.60(AJB.0)b2 | 03/26/2006
[Bug Fix]
36. [SPR: 060308696] Can not get the WAN MAC Address
37. [SPR: 060308702] Step1: Edit Web/Go Wizard setup/Apply/Connection Wizard
Step2: WAN MAC address/Choose "Spoof this computer's MAC
address"/IP address =192.168.1.33/Next/Apply. Message : Can not get the WAN MAC
Address
38. [SPR: 060309826] Bandwidth Management can't work.
39. [SPR: 060309827] SNMP can't work on GUI.
40. [SPR: 060310910]The default "setup key" of OTIST is "01234567" , not null
41. [SPR: 060310912]From the wizard, configure wireless security mode =auto and
enable OTIST function and setup key="01234567", after all process finished , the
OTIST count down page only show 1 sec. In general, it counts down from 180 sec.
42. [SPR: 060310913]From the wizard, configure wireless security mode =auto ,enable

ZyXEL Confidential
360AJB0C1.rtf 5/36
OTIST function and setup key="01234567",after OTIST count down page ,all
process finished, configure wireless setting from Network/wireless , it will show the
message" Auto Security in process ,but I think the OTIST function doesn't work well
43. [SPR: 060310916]Can't keep the 802.11a mode after device reboot.
44. [SPR: 060310917]Channel change cause to wireless mode change.
45. [SPR: 060310919]Ethernet PC can't ping to DUT.
46. [SPR: 060313985]"Reset" button can't work in GUI.
47. [SPR: 060313990]Ethernet PC can't ping to DUT.
48. [SPR: 060313997]Load default first, from e/WC, Network/Wireless, configure
wireless security=WPA ,802.1X or WPA2 ,one wireless station connect to
DUT,when configure any setting ,device exception.
49. [SPR: 060313003]802.11a mode can't work well.
50. [SPR: 060314056]802.11a and 802.11g all can't pass PQA criteria .
51. [SPR: 060314074]Voice quality is very poor with G.711 codec on Phone 1.
52. [SPR: 060314075]DTMF lost with SIP INFO mode on codec is G.729 and G.711.
53. [SPR: 060314077]DUT can't display CLID from PSTN CO simulator.
54. [SPR: 060314079]DUT can't receive FAX through G.729 codec.
55. [SPR: 060314080]DTMF lost on PSTN call.
56. [SPR: 060314081]DUT receive two kinds of busy tone when dial own PSTN number
and disable Trunking.
57. [SPR: 060314083]DUT don't generate secondary dial tone when DUT-A press
FLASH after DUT-A and DUT-B are in conversation.
58. [SPR: 060314084] “hop on” with Auto Attendant can not work correctly.
59. [SPR: 060314085] “hop off” with Auto Attendant can not work correctly.
60. [SPR: 060309829] IGMP-v1 does not work.
61. [SPR: 060309830] IGMP-v2 does not work.
Modification in V 3.60(AJB.0)b1 | 03/03/2006
First release for P2302HWL-P1 Standard Version

ZyXEL Confidential
360AJB0C1.rtf 6/36
Annex A CI Command List
Command Class List Table
System Related Command Exit Command Device Related Command
Ethernet Related Command POE Related Command PPTP Related Command
Configuration Related Command IP Related Command ppp
dsp voice
SystemRelatedCommand Home
Command Description
sys
adjtime retrive date and time from Internet
callhist
display display call history
remove <index> remove entry from call history
countrycode [countrycode] set country code
date [year month date] set/display date
domainname display domain name
edit <filename> edit a text file
extraphnum maintain extra phone numbers for outcalls
add <set 1-3> <1st phone num> [2nd phone
num] add extra phone numbers
display display extra phone numbers
node <num> set all extend phone number to remote node
<num>
remove <set 1-3> remove extra phone numbers
reset reset flag and mask
feature display feature bit
hostname [hostname] display system hostname
logs

ZyXEL Confidential
360AJB0C1.rtf 7/36
category
access [0:none/1:log/2:alert/3:both] record the access control logs
attack [0:none/1:log/2:alert/3:both] record and alert the firewall attack logs
display display the category setting
error [0:none/1:log/2:alert/3:both] record and alert the system error logs
ipsec [0:none/1:log/2:alert/3:both] record the access control logs
ike [0:none/1:log/2:alert/3:both] record the access control logs
javablocked [0:none/1:log] record the java etc. blocked logs
mten [0:none/1:log] record the system maintenance logs
upnp [0:none/1:log] record upnp logs
urlblocked [0:none/1:log/2:alert/3:both] record and alert the web blocked logs
urlforward [0:none/1:log] record web forward logs
clear clear log
display [access|attack|error|ipsec|ike|javablocked|
mten|urlblocked|urlfor
ward]
display all logs or specify category logs
errlog
clear display log error
disp clear log error
online turn on/off error log online display
load load the log setting buffer
mail
alertAddr [mail address] send alerts to this mail address
display display mail setting
logAddr [mail address] send logs to this mail address
schedule display display mail schedule
schedule hour [0-23] hour time to send the logs

ZyXEL Confidential
360AJB0C1.rtf 8/36
schedule minute [0-59] minute time to send the logs
schedule policy
[0:full/1:hourly/2:daily/3:weekly/4:none] mail schedule policy
schedule week
[0:sun/1:mon/2:tue/3:wed/4:thu/5:fri/6:sa
t]
weekly time to send the logs
server [domainName/IP] mail server to send the logs
subject [mail subject] mail subject
save save the log setting buffer
syslog
active [0:no/1:yes] active to enable unix syslog
display display syslog setting
facility [Local ID(1-7)] log the messages to different files
server [domainName/IP] syslog server to send the logs
log
clear clear log error
disp display log error
online [on|off] turn on/off error log online display
resolve Resolve mail server and syslog server address
mbuf
link link list system mbuf link
pool <id> [type] list system mbuf pool
status display system mbuf status
disp <address> display mbuf status
cnt
disp display system mbuf count
clear clear system mbuf count
debug [on|off]

ZyXEL Confidential
360AJB0C1.rtf 9/36
pwderrtm [minute] Set or display the password error blocking
timeout value.
rn
load <entry no.> load remote node information
disp <entry no.>(0:working buffer) display remote node information
nat <none|sua|full_feature> config remote node nat
nailup <no|yes> config remote node nailup
mtu <value> set remote node mtu
save [entry no.] save remote node information
smt not support in this product
stdio [minute] change terminal timeout value
time [hour [min [sec]]] display/set system time
trcdisp monitor packets
trclog
trcpacket
syslog
server [destIP] set syslog server IP address
facility <FacilityNo> set syslog facility
type [type] set/display syslog type flag
mode [on|off] set syslog mode
version display RAS code and driver version
view <filename> view a text file
wdog
switch [on|off] set on/off wdog
cnt [value] display watchdog counts value: 0-34463
romreset restore default romfile
server

ZyXEL Confidential
360AJB0C1.rtf 10/36
access <telnet|ftp|web|icmp|snmp|dns> <value> set server access type
load load server information
disp display server information
port <telnet|ftp|web|snmp> <port> set server port
save save server information
secureip <telnet|ftp|web|icmp|snmp|dns> <ip> set server secure ip addr
fwnotify
load load fwnotify entry from spt
save save fwnotify entry to spt
url <url> set fwnotify url
days <days> set fwnotify days
active <flag> turn on/off fwnotify flag
disp display firmware notify information
check check firmware notify event
debug <flag> turn on/off firmware notify debug flag
cmgr
trace
disp <ch-name> show the connection trace of this channel
clear <ch-name> clear the connection trace of this channel
cnt <ch-name> show channel connection related counter
socket display system socket information
filter
netbios
roadrunner
debug <level> enable/disable roadrunner service
0: diable <default>
1: enable